Sealey MCL500 Single Post Motorcycle Lift Instruction Manual

: June 1, 2024
: SEALEY

Table of Contents

Sealey MCL500 Single Post Motorcycle Lift
Product Usage Instructions
Frequently Asked Questions
SAFETY
INTRODUCTION
SPECIFICATION
ASSEMBLY
OPERATION
MAINTENANCE
TROUBLESHOOTING
ENVIRONMENT PROTECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sealey MCL500 Single Post Motorcycle Lift

Specifications:

Product: Single Post Motorcycle Lift
Model No: MCL500
Maximum Weight Capacity: 450kg

Product Usage Instructions

1. Safety Precautions:

Before using the Single Post Motorcycle Lift, ensure to follow these safety guidelines:

Always secure the motorcycle to the lifting platform with appropriate straps before raising.
Maintain the lift in good condition and replace damaged parts with genuine parts only.
Locate the lift in a suitable work area with a level and strong floor surface.
Keep the lift clean for optimal performance and safety.
Do not exceed the maximum weight capacity of 450kg.

2. Operational Instructions:

Follow these steps for safe operation of the lift:

Check for overhead obstructions before lifting.
Engage the locking pin when the platform is raised to the desired height.
Adjust the lowering speed based on the weight of the load and the release valve setting.
Before lowering, ensure there are no obstructions underneath and keep all persons clear.

3. Prohibited Actions:

Avoid the following actions when using the lift:

Do not use the lift for tasks it is not designed for.
Do not exceed the rated capacity of the lift.
Avoid operating the lift if damaged or under the influence of alcohol or drugs.
Do not make modifications to the lift or tamper with safety features.

4. Storage Instructions:

When storing the lift:

Ensure all parts are clean and free of grease or oil.
Store the lift in the lowest position in a safe area.

Frequently Asked Questions

Q: What should I do if I exceed the maximum weight capacity of the lift?
- A: It is crucial not to exceed the rated capacity of 450kg as it may lead to damage or personal injury. Always check and comply with the weight limits before using the lift.
Q: Can I use brake fluid to top up the hydraulic unit?
- A: No, it is advised not to use brake fluid for topping up the hydraulic unit. Always follow manufacturer recommendations for maintenance and lubrication.
Q: How should I store the lift when not in use?
- A: Make sure all parts are clean and free of grease or oil before storing. Store the lift in the lowest position in a safe area away from unauthorized access.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE

SAFETY

WARNING! Ensure that the motorcycle is adequately secured to the lifting platform with appropriate straps before raising the load.

Maintain the lift in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up hydraulic unit.
Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike.
DO NOT operate the lift on tarmacadam, as the surface may be unstable.
Keep the lift clean for best and safest performance.
The maximum motorcycle weight is 450kg. DO NOT exceed this rated capacity.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes.
Before lifting check that there are no overhead obstructions.
When platform has been raised to the working height ensure the locking pin is engaged to prevent accidental lowering.
Keep children and unauthorised persons away from the work area.
The lowering speed will vary according to the weight of the load and the setting of the release valve.
DO NOT use the lift for a task it is not designed to perform.
DO NOT operate the lift if damaged.
DO NOT exceed the rated capacity of the lift.
DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT allow untrained persons to operate the lift.
DO NOT make any modifications to the lift and DO NOT adjust or tamper with the safety valve.
DO NOT sit or stand on the lift or hold onto it when it is being raised or lowered.
DO NOT attempt to raise the lift using manual strength.
DO NOT allow anyone to stand near the interior frame of the lift whilst raising or lowering.
DO NOT use the ram alone to maintain a raised motorcycle. ALWAYS insert the locking pin.
Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

INTRODUCTION

The space-saving design maximises garage working area. With a low minimum height of 65mm (without frame supports), it will lift and support the bike through to a maximum height of 740mm (840mm with frame supports). Lockable in two positions for supporting the motorcycle over extended periods. Unlike most other motorcycle lifts, it is possible to remove both wheels, front forks, steering assembly, rear swing arm and suspension units as well as the engine. This lift also benefits from being portable and can be used anywhere with a hard level floor, making this suitable for mobile motorcycle mechanics. Ideal for use with the Sealey range of wheel chocks to assist supporting the motorcycle, whilst adjusting the frame supports and securing to the lift.

SPECIFICATION

Model No:…………………………………………………………………………….MCL500
Capacity:………………………………………………………………………………….450kg
Min./Max. Lift Height (without Frame Supports): ………………………65/740mm
Min./Max. Lift Height (with Frame Supports): …………………………165/840mm
Frame Height: …………………………………………………………………………920mm
Maximum Frame Width: ……………………………………………………………980mm

ASSEMBLY

Check parts against parts diagram before assembly
Locate the legs (fig.1.2) into the body assembly (fig.1.1) and see cure using M12 bolts, nuts and washers.
Secure the cradle assembly (fig.1.3) to the upper (fig 1.4) and lower parallel arms (fig.1.5) using pins and M12 nuts and washers.
Secure the head of the hydraulic unit (fig.1.6) to the body assembly (fig.1.1) using an M12 bolt, nut and washers.
The foot of the hydraulic unit is secured using 2 x M8 internal hex bolts with nuts and washers.
Locate the pumping handle (fig.1.7/2.1) into the pump socket (fig.2.2).
BLEEDING THE HYDRAULIC UNIT
The hydraulic unit will require bleeding before use owing to the oil being disturbed during transport. Open the release valve (fig.2.3) slightly and pump about 20 strokes with the pump handle (2.1). Close the valve and top-up the reservoir with a good quality jack oil HJO500HLS, HJO5LS (NOT brake fluid). To do this, remove the reservoir cap (fig.2.4) and fill to just below the level of the entry. Replace the cap.
The action of the jack should now be firm, all air having been expelled from the system. If not, repeat step 4.6.1.
When not in use, the locking pin should be kept safe by placing it in the top of the body assembly as in fig.1.9.

OPERATION

WARNING! Ensure that you read, understand and apply the safety instructions before use.
WARNING! DO NOT attempt to overload the lift.

Position the lift in a suitable area, checking that the surface on which the lift will stand is solid and flat (preferably concrete).To move the lift, pull back until the wheels are in contact with the ground.
The lift may be used either with or without the frame supports (fig.1.8) in place. If desired, drop the threaded stems through the slots in the cradle frame and secure the stands in the correct position with an M16 nut. A second nut may be fitted to the stem above the frame to alter the relative height of the stands. 8 DO NOT attempt to lift a motorcycle without securing to the cradle with suitable ratchet straps.
Position the cradle beneath the motorcycle and adjust the position of the frame supports beneath suitable parts of the frame, taking care not to damage any exhaust components, pipes or cables. (see fig.3).
TOLIFT: Close the release valve fully and use the pump handle to raise the cradle into light contact with the motorcycle frame. Tighten the nuts on the frame support stems to lock.
Secure the load with ratchet straps.
Pump up to a convenient height; DO NOT leave the load supported by the hydraulic unit alone; insert the locking pin into the hole below the lower arm and lower the arm gently onto the pin (fig.4) by opening the release valve (fig.2.3) gradually.
TOLOWER: Before lowering, ensure that the area below the cradle is clear and that everyone stands well clear of the mechanism. Close the release valve and pump the cradle clear of the locking pin. Remove the locking pin.
Open the release valve gradually to allow the cradle to descend gently
When the motorcycle is bearing its own weight, close the release valve and remove the strapping; when removed, open the release valve again to allow the cradle to settle at its minimum height.
Withdraw the lift from beneath the motorcycle.
Store in a safe, dry, child-proof location when not in use. $Sealey-MCL500-Single-Post-Motorcycle-Lift-fig $5$$

MAINTENANCE

When the lift is not in use, it must be returned to its lowest position to minimise ram and piston corrosion.
Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts.
Before each use check all parts. If any part of the lift is damaged or suspected, remove lift from service and take necessary action to repair. 8 DO NOT use the lift if it is believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
Check the ram and piston periodically for signs of corrosion. Clean exposed areas with a clean oiled cloth.
Topping up the oil. Top up the oil as in section 4.6.1. above. Use only a good quality jack oil HJO500HLS, HJO5LS. 8 DO NOT use any other fluid such as: brake fluid, automatic transmission fluid or engine oil.

TROUBLESHOOTING

SYMPTOM	POSSIBLE CAUSES	SOLUTION
Jack will not lift load.	Release valve not tightly closed.	Close release

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR