ROBERT JULIAT 653SX 4C Colour LED Profile Spot User Guide

200 W LED
Manual
4-COLOUR LED PROFILE SPOT
V2
DN41222400-A (EN)
VALIDATION : 21/09/23
– FIRMWARE: V2.xx
Robert Juliat S.A.S. 32, rue de
Beaumont, F 60530 Fresnoy-en-Thelle
– phone : +33 (0)3 44 26 51 89
– info@robertjuliat.fr
www.robertjuliat.com

653SX 4C Colour LED Profile Spot

REF

| Standard|

North American

---|---|---
28 – 54°| 653SX 4C| 653CSX 4C
16 – 35°| 654SX 4C| 654CSX 4C
11 – 26°| 651SX 4C| 651CSX 4C

User’s instructions

GENERAL INSTRUCTIONS

1. Not for residential use.

2. These fixtures must only be serviced by a qualified technician.

3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU Directives must be adhered to at all times.

4. This fixture is in compliance with section 17 – Lighting appliance for theatre stages, television, cinema and photograph studios. Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.

5. This fixture is rated as IP20, and is for indoor use only.
   FIXTURE

6. Ensure fixture is correctly mounted on an appropriate support.

7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since these might reduce performance.

8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable length.

9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or rolled up as necessary, to minimise travel distance should the fixture be dislodged.

10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.

11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of safety cable or bond.

12. Do not open lighting fixture when the source is on.

13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.

14. Do not tamper with design of fixture nor any of its safety features.

15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.

16. Use only with correct power supply.
    VENTILATION

17. Keep well away from flammable material.

18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.

19.  To avoid overheating, do not obstruct air vents.

20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as necessary.
    CLEANING

21. Do not touch the LED source with your fingers.

22. To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics. Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage. Dry with a soft lint-free cloth.

23. Regularly remove dust with a soft lint-free cloth.

24. If the fixture has filters, they must be cleaned frequently.
    POWER SUPPLY

25. Disconnect from the mains before servicing.

26. Mains connection only. Do not connect to “electronic output” such as dimmer.

27. Ensure power supply circuit breakers, always remain accessible.

PLEASE NOTE
This product has been built to conform to European standards relating to professional lighting equipment.
Any modification made to our products will void the manufacturers’ warranty.
Risk group 2
CAUTION: Possibly hazardous optical radiation emitted from this product.
Do not stare at operating lamp.
Maybe harmful to the eye.Group risk 2. Luminaires should be positioned so that prolonged staring into luminaire at a distance closer than 18,7m (651SX 4C), 8m (653SX 4C) & 13,5m (654SX 4C) is not expected.

Presentation

2.1 Functions Description

1. Identification plates
2. Data connector (IN and OUT)
3. Power connector (IN and OUT)
4. Local display and controls
5. Handle
6. Safety cable attachment point
7. Hanging yoke
8. Tilt index
9. Tilt locking handle
10. Shutters| 11. Shutter locking system
12. Lens tube rotation locking button
13. Lens tube access
14. Focus adjustment
15. Front slot for accessories and gel frame holder
16. Front slot locking system
17. Zoom adjustment
18. Gobo holder
19. Iris
---|---

2.2 Identification labels
2.2.1 Label on LED compartment
Description Units :
– Weight = kilogram (kg).
– Intensity = Ampere (A).
– Voltage = Volt (V).
– Frequency = Hertz (Hz).
– Temperature = degree Celsius (°C).

1. MOD. : Model
2. VERS. : Version
3. U : Nominal voltage input (V)
4. I : Nominal intensity (A)
5. P : Maximum power input (W)
6. IP : International Protection Rating
7. t°a : Maximum ambient temperature (°C)
8. t°c : Maximum external temperature of the unit (°C)
9. Net weight (kg)
10. Minimum distance between a flammable material and the lighting unit (m)| 11. LED type
12. Serial number
13. Replace broken glass
14. Class 1 product label
15. Read manual first label
16. European conformity label
17. WEEE directive label
18. CEI-TR-62778 – Do not stare at light source
19. EN62471 – Risk group
20. UKCA (UK Conformity Assessed) label
---|---

2.2.2 Label on lighting unit
Description Units :
– Weight = kilogram (kg).
– Intensity = Ampere (A).
– Voltage = Volt (V).
– Frequency = Hertz (Hz).
– Temperature = degree Celsius (°C).

1. Model beam angles
2. Net weight (kg) without LED compartment
3. Serial number
4. Class 1 product label
5. Read manual first label
6. European conformity label
7. WEEE directive label
8. Operating positions
9. UKCA (UK Conformity Assessed) label

2.3 Accessories included![ROBERT JULIAT 653SX 4C Colour LED Profile Spot

• Accessories included](https://manuals.plus/wp-content/uploads/2024/04 /ROBERT-JULIAT-653SX-4C-Colour-LED-Profile-Spot-Accessories-included.png)

| Reference| Description
---|---|---
1| PF500M2| 180 x 180 mm (7.1 x 7.1 in) metal filter holder
2| SGUX| Universal A-size gobo holder (metal, glass, frosted glass)
3| D8| Shutter (x4)
4| DN41222600| Quick Start manual
1| CAL03| 3 meter power cable ( 3G1,5 HO7RNF) with Neutrik PowerCon© True1 TOP and CEE 7/7 (2P+T NF/SCHUKO) connectors (standard version)
2| CAL04| 1,50m power cable UL/CSA with Neutrik PowerCon© True1 TOP connector (North American version)

2.4 Accessories

| Reference| Description
---|---|---

1

| CAV 600A| Double slot front cassette for 180 x 180 mm accessories
CAV 600AE| Double slot front cassette for 185 x 185 mm accessories
2| PCP1716A| 16A blue 2P+E 6h IEC60309 power connector
3| PF600M2| 185 x 185 mm (7.28 x 7.28 in) metal filter holder
4| G500| 180 x 180 mm safety grid
5| IWSX755| Drop-in iris (monoplane) with holder
6| VD 120| 120 x 120 mm inner frosted glass
7| FCD600| Angled yoke
8| D8| Shutter
9| 876| Hook clamp 40 x 10 mm with 28 mm M10 screw for Ø35 to Ø50 mm pipes
10| 880| Hook clamp 40 x 10 mm with 28 mm M10 screw for Ø50 to Ø63 mm pipes
11| CS2| Safety cable Ø3 mm (length = 600 mm)
12| APH 68LED| Double-condenser set for Led profile
13| T/650SXCW| SULLY 115 W LED compartment – Cool White – 3 meter power cable with CEE 7/7 (2P+T NF/ SCHUKO) connector
14| T/650SXWW| SULLY 115 W LED compartment – Warm White – 3 meter power cable with CEE 7/7 (2P+T NF/ SCHUKO) connector
15| TH600| 180 x 180 mm “Top hat” (without safety cable)
16| FO100-10| Ø97 mm optical filter for coloured LED source – type 10
17| DMXcat| Bluetooth DMX/RDM Multifunction test tool – City Theatrical DMXcat®

Set-up

3.1 Mechanics
3.1.1 Operating positions 3.1.2 Minimum distance between a flammable material and the lighting unit 3.1.3 Instructions for use 3.1.4 Hanging
Ensure fixture is correctly mounted on an appropriate support Net weight:
653SX 4C = 12.8 kg (28.2 lbs)
654SX 4C = 14.1 kg (31,1 lbs)
651SX 4C = 14.5 kg (32 lbs)
3.1.5 Safety cable

• When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety bond or cable) of suitable length.
• The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of safety cable or bond.
• Safety cables or bonds must be securely attached to the back of the fixture and be as short as possible, or rolled up as necessary, to minimise travel distance should the fixture be dislodged.

3.2 Electrical information
3.2.1 LED source
Never touch or scratch the LED surface.
TSee 6.1.4 LED cleaning procedure if cleaning is necessary.
3.2.2 Power supply

Power supply

Voltage| Frequency| Input power| Connectors
100 T 264 V| 50-60 Hz| 0.88 A / 175 W @ 230V cos y = 0,87
1.68 A / 178 W @ 110V cos y = 0,98
1.82 A / 178 W @ 100V cos y = 0,99
180 W max, Max: 2.1 A| Neutrik powerCON TRUE1 TOP
Input : ref. NAC3FPX-TOP
** •   Class 1 product. This luminaire must be earthed.
•   Must be connected directly to AC power. Do not connect to dimmer power.
** •   Automatic mains voltage detection.

Daisy chain (with delivered power cable Power cable

Power cable| Connector| Mains plug| Cable type| Cable length| Wiring
---|---|---|---|---|---
1| Standard version| Neutrik® powerCON TRUE1 TOP NAC3FX-W-TOP|

CEE7/7

| 3G1.5 H07RNF| 3 m
9.8 ft| Live: Brown
Neutral: BlueGround: Yellow/Green
2| North American version| __

–

| 14AWG SJ TYPE (UL/CSA)| 1.5 m
4.9 ft| Live: Black
Neutral: White
Ground: Green

3.3 DATA
3.3.1 DMX 512-A / RDM

DATA connectors

__

PIN #| DMX|

Description

---|---|---
1| Shielding| Foil & Braided Shield
2| DMX (-)| 1st conductor of 1st twisted pair
3| DMX (+)| 2nd conductor of 1st twisted pair
4| Not used| 1st conductor of 2nd twisted pair
5| Not used| 2nd conductor of 2nd twisted pair

Daisy chain:

3.4 Accessories
3.4.1 Front filter holder![ROBERT JULIAT 653SX 4C Colour LED Profile Spot

• Front filter holder](https://manuals.plus/wp-content/uploads/2024/04/ROBERT- JULIAT-653SX-4C-Colour-LED-Profile-Spot-Front-filter-holder.png) The filter holder includes perforations designed for stapling to keep the gel in position.
  3.4.2 Double-condenser set
  Only possible with LED version (not with halogen)
  3.4.3 Internal filter holder 3.4.4 Gobo holder / Iris 3.4.5 Shutters

Operations

4.1 Source type
4.1.1 Range

| Compatible functions
---|---
Colour Mix| Colour Temperature CCT| High Brightness| High Quality| Colour Filters| DimShift
Source type| See 4.3| See 4.4| See 4.5| See 4.5| See 4.6| See 4.9
Tungsten 3200 K – DimShift| | | | X| X| X
Tungsten 3000 K – DimShift| | | | X| X| X
Tungsten 3200 K| | | | X| X|
Tungsten 3000 K| | | | X| X|
Daylight 6500 K (D65)| | | | X| X|
Generic CCT – High Quality| | X| | X| X|
Generic CCT – High Brightness| | X| X| | X|
Generic CCT – High Quality – DimShift| | X| | X| X| X
Generic CCT – High Brightness – DimShift| | X| X| | X| X
Colour Mix – High Quality| X| | | X| |
Colour Mix – High Brightness| X| | X| | |

4.1.2 Control

Remotely with DMX512-A protocol
Mode 3 – 4 – 5 – 6 (see 5.2.4 DMX chart for function details) Locally with DMX mode 1 – 2 and
Stand Alone mode – see 5.6 Home value
4.2 Light intensity
4.2.1 Range 4.2.2 Control Remotely with DMX512-A protocol Mode 1 – 2 – 3 – 4 – 5 – 6 (see 5.2.4 DMX chart for function details) Locally via
STAND ALONE mode

Focus mode: when standby screen displayed, Push the UP arrow button for 3 secs → Light output = 100% for 1 minute
Push the UP arrow button to Exit → Light output = 0%
4.2.3 Parameters
4.2.3.1 Dimming resolution – DMX only
**** Set through RDM protocol, DMX control channel or local control.

4.2.3.2 Dimming curve
** Set through RDM protocol or local control 4.2.3.3 Dimming mode
** Set through RDM protocol or local control

(*) Default value
4.2.3.4 Response time
** See 4.8
4.2.3.5 DimShift
**See 4.9
4.3 Colour mix
4.3.1 Range 4.3.2 Control Remotely with DMX512-A protocol

CIE xy| Mode 3 | Source type = Colour Mix
---|---
Hue Saturation| Mode 4 | Source type = Colour Mix
RGB| Mode 5 | Source type = Colour Mix
RAW| Mode 6 | Source type = Colour Mix

Locally via
STAND ALONE mode – see 5.6 Home value

4.3.3 Parameters
4.3.3.1 Colour space selection
****Set through RDM protocol, DMX control channel or local control
– For RGB and Hue Saturation modes only

4.3.3.2 High Quality / High Brightness
**See 4.5
4.4 Colour Temperature CCT
4.4.1 Range 4.4.2 Control** Remotely with DMX512-A protocol
Mode 3 – 4 – 5 – 6 | Source type = Generic CCT (see 5.2.4 DMX chart for function details) Locally with DMX mode 1 – 2 and Stand Alone mode – see 5.6 Home value

4.4.3 Parameters
4.4.3.1 High Brightness / High Quality
** See 4.5
4.4.3.2 DimShift
**See 4.9
4.5 High Brightness / High Quality
4.5.1 Range

Example : Generic CCT @ 5600K![ROBERT JULIAT 653SX 4C Colour LED Profile Spot

• Colour mix 4](https://manuals.plus/wp-content/uploads/2024/04/ROBERT-JULIAT- 653SX-4C-Colour-LED-Profile-Spot-Colour-mix-4.png) 4.5.2 Control Remotely with DMX512-A protocol
  Mode 3 – 4 – 5 – 6 | Source type = Generic CCT / Colour Mix
  (see 5.2.4 DMX chart for function details) Locally with DMX mode 1 – 2 and
  Stand Alone mode – see 5.6 Home value
  4.6 Colour filters
  4.6.1 Range 4.6.2 Control
  (*) Results depend on Source type or Colour temperature – compatible with White presets, Generic CCT source types and DimShift function Remotely with DMX512-A protocol
  Mode 3 – 4 -5 – 6 | Source type = White presets /Generic CCT (see 5.2.4 DMX chart for function details) Locally with DMX mode 1 – 2 and
  Stand Alone mode – see 5.6 Home value

Colour filter selection:
1. Selection of the colour wheel

2. Selection of the gel reference **** See annex for reference details

4.6.3 Parameters
4.6.3.1 Saturation 4.6.3.2 Transmission **** Filter transmission is independant from main dimmer. Dimmer intensity can still be operated from 0 to 100% with or without the DimShift function

4.6.3.3 Gel Fade Time and Mode
Transition between 2 colour filters – Gel fade time:Transition between 2 colour filters – Gel Fade type: 4.7 Strobe
4.7.1 Range 4.7.2 Control ****Remotely with DMX512-A protocol.
Mode 2 – 3 – 4 – 5 – 6 (see 5.2.4 DMX chart for function details)

4.8 Response time
4.8.1 Range 4.8.2 Control Remotely with DMX512-A protocol Mode 2 – 3 – 4 – 5 – 6
(see 5.2.4 DMX chart for function details) Locally with DMX mode 1 and
Stand Alone mode – see 5.6 Home value
4.9 DimShift
4.9.1 Range
DimShift function:
When dimming the light, the colours follow the Planck curve (tungsten redshift emulation)   4.9.2 Control Remotely with DMX512-A protocol
Mode 3 – 4 – 5 – 6 | Source type = White presets / Generic CCT
(see 5.2.4 DMX chart for function details) Locally with DMX mode 1 – 2 and
Stand Alone mode – see 5.6 Home value
4.10 Beam size adjustment
4.10.1 Range

4.10.2 Control 4.11 Orientation
4.11.1 Range 4.11.2 Control 4.12 Colour and diffuser filters (gels)
Fixed colour:

Location|
---|---
1. Front filter holder| 2. Internal filter holder
Type| Standard coloured gel filter| Frosted or dichroic glass
Dimensions|

| **
Installation| See 3.4.1| See 3.4.3**

4.13 Beam shaping
4.13.1 Range

4.13.2 Control **See 3.4 Accessories for gobo, iris and additional shutters installation
4.14 Beam rotation
4.14.1 Range** 4.14.2 Control

4.15 Gobos

Controls and parameters

5.1 Local display and controls
5.1.1 Display

Function

__

| Exit the current menu option and/or go back

__

| Enter the current menu option and/or valid

__

| Scroll through menus and/or Increase data value

__

| Scroll through menus and/or Decrease data value

__

| Menu down and/or Increase data value

__

| Menu up and/or Decrease data value

5.1.2 Home screen 5.1.3 Menu 5.1.4 Parameters
5.1.4.1 Backlight
**Selection in SETUP / DISPLAY / BACKLIGHT menu 5.2 DMX512 – A remote control
5.2.1 Protocol
E1.11 – 2008, USITT DMX512-A
5.2.2 Configuration**

1 – Set DMX address
2 – Set personality mode (see 5.2.4. DMX chart)

1 – Set DMX mode: 2 – Set Personality mode: 3 – Set DMX address: 5.2.3 Parameters
5.2.3.1 DMX Hold
** Selection in SETUP / Data Setup / DMX HOLD menu 5.2.3.2 User ID
** Selection in SETUP / Data Setup / USER ID menu
Each unit can be identified by a User ID number – Once defined, the User ID is displayed on the Home screen.

Example: Installation with 6 units| | | | | |
---|---|---|---|---|---|---
Home screen information| ID1 @ 101| ID2 @ 123| ID3 @ 145| ID4 @ 167| ID5 @ 189| ID6 @ 211
User ID| 1| 2| 3| 4| 5| 6
DMX address| 101| 123| 145| 167| 189| 211

5.2.3.3 Transfer settings
**** Selection in SETUP / Data Setup / TRANSFER SETTINGS menu

1. Setup of the first unit
2. Transmission of all parameters to the other units connected by DMX

DMX address) + Setup

5.2.4 DMX chart

__

DMX Channel

| Mode 1| Mode 2| Mode 3| Mode 4| Mode 5| Mode 6
---|---|---|---|---|---|---
Dimmer8B| Profile16b| Full – XY| Full – HS| Full – RGB| Full – Raw
1| Dimmer| Dimmer| Dimmer| Dimmer| Dimmer| Dimmer
2| | Dimmer fine| Dimmer fine| Dimmer fine| Dimmer fine| Dimmer fine
3| | Strobe duration| Strobe duration| Strobe duration| Strobe duration| Strobe duration
4| | Strobe speed| Strobe speed| Strobe speed| Strobe speed| Strobe speed
5| | Response time| Response time| Response time| Response time| Response time
6| | Control mode| Control mode| Control mode| Control mode| Control mode
7| | | Source Type| Source Type| Source Type| Source Type
8| | | Gel: Type| Gel: Type| Gel: Type| Gel: Type
9| | | Gel: Reference| Gel: Reference| Gel: Reference| Gel: Reference
10| | | Gel: Saturation| Gel: Saturation| Gel: Saturation| Gel: Saturation
11| | | Gel: Transmission| Gel: Transmission| Gel: Transmission| Gel: Transmission
12| | | Gel: Fade Time| Gel: Fade Time| Gel: Fade Time| Gel: Fade Time
13| | | Gel: Fade Mode| Gel: Fade Mode| Gel: Fade Mode| Gel: Fade Mode
14| | | Tunable white: CCT| Tunable white: CCT| Tunable white: CCT| Tunable white: CCT
15| | | Tunable white: CCT fine| Tunable white: CCT fine| Tunable white: CCT fine| Tunable white: CCT fine
16| | | Tunable white: Delta UV| Tunable white: DeltaUV| Tunable white: Delta UV| Tunable white: Delta UV
17| | | Colour: X| Colour: Hue| Colour: Red| Colour: Red
18| | | Colour: X fine| Colour: Hue fine| Colour: Red fine| Colour: Red fine
19| | | Colour: Y| Colour: Saturation| Colour: Green| Colour: Green
20| | | Colour: Y fine| Colour: Saturation fine| Colour: Green fine| Colour: Green fine
21| | | | | Colour: Blue| Colour: Blue
22| | | | | Colour: Blue fine| Colour: Blue fine
23| | | | | | Colour: Lime
24| | | | | | Colour: Lime fine

5.2.5 DMX ranges
5.2.5.1 Strobe duration

5.2.5.2 Strobe speed

5.2.5.3 Response time

**5.2.5.4 Control mode***

5.2.5.5 Source Type
(*) Function activated after 5 seconds – need to go back to zero to activate second function.

5.2.5.6 Gel Type

CCT”
5| 9| Wheel 2| Numeric: 002 –> 111
10| 14| Wheel 3| Numeric: 113 –> 181
15| 19| Wheel 4| Numeric: 182 –> 328
20| 24| Wheel 5| Numeric: 332 –> 710
25| 29| Wheel 6| Numeric: 711 –> 799
30| 34| Wheel 7| Chroma: 048 –> 719
35| 39| Wheel 8| Chroma: 711 –> 504
40| 44| Wheel 9| Chroma: 730–> 007
45| 49| Wheel 10| Chroma: 765 –> 789
50| 54| Wheel 11| Chroma: 787 –> 344
55| 59| Wheel 12| Cosmetic & Corrections
60| 64| Wheel 13| Dalis selection
65| 254| | | Not used

5.2.5.7 Gel references
**See annex for reference details
5.2.5.8 Gel Saturation
**

5.2.5.9 Gel Transmission

5.2.5.10 Gel Fade Time

CCT”

5.2.5.11 Gel Fade Mode

whites” & “Generic CCT”
11| 20| Direct XY
21| 30| Open Frame + Limit Brightness
31| 40| Open Frame
41| 50| Through Black
51| 255| Reserved / Off (0 s)

5.2.5.12 CCT

5.2.5.13 DeltaUV

5.2.5.14 Colour CIE x

5.2.5.15 Colour CIE y

5.3 RDM remote control
5.3.1 Protocol
ANSI E1.20 – 2010 / ANSI E1.37 – 1
For more information on the RDM protocol: http://www.rdmprotocol.org/
5.3.2 PIDs list

5.3.3 Parameters
RDM: ON/OFF
****Selection in SETUP / Data Setup / RDM menu

5.4 Fan cooling modes
5.4.1 Range

5.4.2 Control

|
---|---
Remotely by DMX512-A
Mode 2 – 3 – 4 – 5 – 6 (see 5.2.4 DMX chart for function details)| Locally ****selection in SETUP / COOLING

5.5 LEDs Feedback
5.5.1 Trouble shooting
During unit initialisation (power up) – up to 5 seconds:

1
DMX OUT| 2
DMX IN| Description
---|---|---
| | Error
| | No DMX protocol detected
| | DMX protocol detected
| | DMX protocol detected + RDM protocol activated

5.5.2 Parameters
5.5.2.1 Auto-OFF
****Set through RDM protocol or local control

ON

Timer with warning

| Feedback LED OFF after 20 seconds ON , if warning information occurs ERROR LED always ON

5.6 Home values
5.6.1 Range
****Selection in SETUP / HOME VALUES menu
If the function is not controlled by DMX, HOME VALUE is automatically activated

**Functions *| DMX Dimmer mode (mode 1)| DM Profile mode (mode 2)| DMX Full mode (mode 3-4-5-6)| ****Stand Alone**
---|---|---|---|---
Dimmer| DMX value| DMX value| DMX value| Home value
Strobe duration| NA| DMX value| DMX value| NA
Strobe speed| NA| DMX value| DMX value| NA
Response time| Home value| DMX value| DMX value| NA
Control mode| NA| DMX value| DMX value| NA
Source Type| Home value| Home value| DMX value| Home value
Gel: Type| Home value| Home value| DMX value| Home value
Gel: Reference| Home value| Home value| DMX value| Home value
Gel: Saturation| Home value| Home value| DMX value| Home value
Gel: Transmission| Home value| Home value| DMX value| Home value
Gel: Fade time| NA| NA| DMX value| NA
Gel: Fade mode| NA| NA| DMX value| NA
Tunable white: CCT| Home value| Home value| DMX value| Home value
Tunable white: Delta UV| Home value| Home value| DMX value| Home value
Colour: Red| Home value| Home value| DMX value| Home value
Colour: Green| Home value| Home value| DMX value| Home value
Colour: Blue| Home value| Home value| DMX value| Home value
Colour: x| Home value| Home value| DMX value| Home value
Colour: y| Home value| Home value| DMX value| Home value
Colour : Hue| Home value| Home value| DMX value| Home value
Colour: Saturation| Home value| Home value| DMX value| Home value

(*) Functions are displayed depending on DMX mode and Source Type selected (example : Red, Green, Blue are available if Source Type = Colour Mix)

Service

6.1 Preventive maintenance
6.1.1 Frequency
General maintenance should be performed at least once a year or more frequently if the equipment is operated in adverse conditions (smoke, heat, humidity, touring, etc.).
6.1.2 General cleaning
Remove dust from the unit.
Front glasses can be cleaned with solutions containing alcohol.
6.1.3 General visual check

•  No trace of heat.
• No loose contacts.
• No missing parts.
• Tighten mechanical assemblies (screws, bolts and nuts, etc.).

6.1.4 LED source

• Do not touch the surface of the LED source (no contact with your hands or any tools) – See section 6.1.7 for the removal and installation procedure of the LED module.
• Do not put compressed air directly on the source.
• Contact a certified RJ distributor in case of residuals or other objects located on the surface of the LED source.

6.1.5 Optics
Only use solutions containing alcohol to clean optical parts (lenses).
– To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics. Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage.
– Dry with a soft lint-free cloth.  6.1.6 LED house cleaning
Inner parts & lens holder access:

• To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics. Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage.
• Dry with a soft lint-free cloth.
• The double condenser system (aspheric and biconvex lenses) can easily be removed, without tools, by removing the two M6 nuts. The complete holder can then be removed for cleaning, see section 3.4.2.

6.1.7 LED module cleaning procedure
How to remove the Sully LED module:

1. We recommend you place your luminaire on a flat clean surface.
   Disconnect from the mains before servicing.

2. Remove the two screws with a flat screwdriver.

3. Unlock the quarter turn screw with a flat screwdriver.

4. Slightly slide out the LED module and remove the earth attachment before removing it completely from it’s housing.

5. Carefully place the LED module on a flat clean surface. Sully LED module installation:

6. Extend the hinge to its maximum position to make it easily accessible.
   Insert the Sully 4C LED module into your luminaire, making sure it is positioned vertically to enable the LED module to enter the lamp house correctly.

7. Connect the ground connection (faston tab terminal) to the Sully 4C LED module.
   – Tighten the faston tab terminel.

8. Once the Sully 4C LED module is fully inserted, tighten the two screws nearest the shutter gate.
   Re-tighten the quarter turn screw located at the back of the lamp base to lock the LED module securely into your luminaire.

6.2 Analysis
In case of problem, contact RJ distributor with the following information:

• Model, version and serial number of the product.

• From the menu status:
  – Software version
  – LED board IDs
  – Device hours

• Description of the problem.

6.3 Electronic thermal management system
In case of overheating, light intensity will be reduced by the system.
Power reduction and temperature values are available by using a RDM protocol compatible device or in the “Status” menu of the fixture.
6.4 Firmware update
A USB/DMX dongle is required and be connected to your PC (no Mac compatibilty at the present time) from an USB port to the DMX input of Sully 4C.
USB-Dongle compatibility:
– All Enttec USB-DMX Dongle
– All USB-DMX Dongle based on FTDI chip
Software Platform compatibility:
– Windows 7/8/10

1. Extract the content of folder “Firmware Updater” (including subfolder) to your PC.
2. Connect USB-DMX dongle device via USB to your PC.
3. Connect one or more Fixtures via DMX Cable.
4. Run “RobertJuliat Firmware Updater.exe”
5. The USB-DMX device should be shown in the lower left corner as “Current interface: FTDI FIUP012021…” If not, click “Interfaces” – “Refresh Interfaces List”.
6. Click “Select File” and select the desired update file (*.dmx)
7. Click “Start”
8. All fixtures of the type specified in the update file will automatically enter in Bootloader mode and update their firmware

6.5 Factory defaults
6.5.1 Modes

6.5.2 Control

Set to factory defaults / reset through RDM protocol| Set to factory defaults / reset through local control
---|---
|

Annex 1 – Gel References Annex 2 – Home values
1. General:
“Home Values” represents a set of parameters manually entered into the device via the keypad in order to restore a predefine setup when a full control of the fixture by DMX is not present, available or allowed. Those home values are used in the following cases:
Loss of DMX signal data: From Menu – “Set Up” then “Data Setup” and Select “DMX Hold”
Standalone Mode : From Menu “Data Mode” then “Protocol” and Select “Standalone”
16 bit Personality Mode: From Menu “Data Mode” then “Personality” and Select “Profile 16 bit”
8 bit Personality Mode: From Menu “Data Mode” then “Personality” and Select “Dimmer 8 bit”
2. Set up the “Dimmer 8 bit” mode :
In “Dimmer 8 bit” mode , the default source is a 3200K halogen source with DimShift (reddening of the filament), halogen dimming curve and a response time corresponding to a 1000W lamp.

BASIC SETUP IN 4 STEPS

DATA MODE
Personality| Mode 1 : Dimmer 8 bit| | Select Personnality Mode:
Mode 1 – Dimmer 8 Bit : 1 Channel DMX
DATA MODE
DMX address| 001 – 512| | Select DMX Address
SET UP
Home values| Gel Type|

| Select the Color Wheel according to your chosen Gel reference
SET UP
Home values| Preset colour| | Select your Gel reference from the dropdown list

OTHER PARAMETERS AVAILABLE

SET UP
Home values
Dimmer Source type Colour mix Response time
Tungsten power Gel saturation Gel transmission
Tunable white CCT Tunable white delta UV Color Red
Color Green Color Blue| ****| All other parameters are available according to the source type selected and technical choices

Documents / Resources

| ROBERT JULIAT 653SX 4C Colour LED Profile Spot [pdf] User Guide
653SX 4C Colour LED Profile Spot, 653SX, 4C Colour LED Profile Spot, LED Profile Spot, Profile Spot, Spot
---|---

References

• RDM Protocol – Information about the RDM Protocol for lighting configuration and control
• ROBERT JULIAT - Robert Juliat is a leading specialist in the manufacture of high-quality PC, Fresnel and profile spots, followspots, and cyclorama and foot-lighting for theatres, opera houses, TV, architecture and more. Made in France since 1919.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>