ROBERT JULIAT 1166 300W LED Followspot Instruction Manual

: June 9, 2024
: ROBERT JULIAT

ROBERT JULIAT 1166 300W LED Followspot

ROBERT JULIAT 1166 300W LED Followspot-PRODUCT

Product Information: Robert Juliat 1166/C Followspot

Product Name: Robert Juliat 1166/C Followspot
Model Number: REF 1166/1166C
Version : V2
Product Type: Standard North American Followspot
Manufacturer: Robert Juliat S.A.S.
Address: 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle
Phone: +33 (0)3 44 26 51 89
Fax: +33 (0)3 44 26 90 79
Email: info@robertjuliat.fr
Website: www.robertjuliat.com
Validation Date: 26/01/22
Compliance Standards: NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE
IP Rating: IP20 (Indoor use only)
Power Consumption: 300W LED

Product Usage Instructions:

This product is not for residential use.
This product should only be serviced by a qualified technician.
Adhere to relevant health and safety requirements of the appropriate EU Directives at all times.
This fixture is in compliance with section 17 – Lighting appliance for theatre stages, television, cinema, and photograph studios.
This fixture is rated as IP20 and is for indoor use only.
Ensure the fixture is correctly mounted on an appropriate support.
Protection screens and lenses must be replaced if damaged, as these might reduce performance.
When hung or flown, the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable length.
Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible or rolled up as necessary to minimize travel distance should the fixture be dislodged.
Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of safety cable or bond.
Do not open the lighting fixture when the source is on.
Allow the fixture to cool before servicing, as LED sources become hot during use.
Do not tamper with the design of the fixture nor any of its safety features.
Tighten electrical mains cable connections regularly and replace with one of identical specifications if damaged.
Use only with the correct power supply.
Keep well away from flammable material and do not cover the fixture or permit it to get wet.
To avoid overheating, do not obstruct air vents and ensure any cooling fans are in correct working order. If fans are not working, turn off the fixture immediately and service as necessary.
To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics. Do not touch the LED source with your fingers.

GENERAL INSTRUCTIONS

Not for residential use.
These fixtures must only be serviced by a qualified technician.
In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU Directives must be adhered to at all times.
This fixture is in compliance with section 17 – Lighting appliance for theatre stages, television, cinema and photograph studios. Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.
This fixture is rated as IP20, and is for indoor use only.

FIXTURE

Ensure fixture is correctly mounted on an appropriate support.
Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since these might reduce performance.
When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable length.
Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or rolled up as necessary, to minimise travel distance should the fixture be dislodged.
Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of safety cable or bond.
Do not open lighting fixture when the source is on.
WARNING: LED source become hot during use. Allow fixture to cool before servicing.
Do not tamper with design of fixture nor any of its safety features.
Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
Use only with correct power supply.

VENTILATION

Keep well away from flammable material.
Not for outdoor use. Do not cover. Do not permit fixture to get wet.
To avoid overheating, do not obstruct air vents.
Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as necessary.

CLEANING

Do not touch the LED source with your fingers.
To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics. Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage. Dry with a soft lint-free cloth.
Regularly remove dust with a soft lint-free cloth.
If the fixture has filters, they must be cleaned frequently.

POWER SUPPLY

Disconnect from the mains before servicing.
Main connection only. Do not connect to “electronic output” such as a dimmer.
Ensure power supply circuit breakers, always remain accessible.

PLEASE NOTE
This product has been built to conform to European standards relating to professional lighting equipment. Any modification made to our products will void the manufacturer’s warranty.

Risk group 2

CAUTION: Possibly hazardous optical radiation is emitted from this product. Do not stare at the operating lamp. May be harmful to the eye.

Group risk 2. Luminaires should be positioned so that prolonged staring into luminaire at a distance closer than 11,4m is not expected.

Photobiological safety according to EN62471

Presentation

Functions

Identification plate
Data connectors (IN and OUT)
Power connectors (IN and OUT)
Thermal breaker
Power switch
Control board
Wireless DMX antenna (option)
Handle
Safety cable attachment point
Yoke
Tilt index
Tilt locking handle
Gate: slots for gobo holder and/or iris
Dimmer rotary knob
Colour changer
Focus adjustment
Lens tube access
Zoom adjustment
Display screen

Identification label

Description

MOD.: Model
VERS. : Version
U: Nominal voltage input (V)
I: Nominal intensity (A)
P: Maximum power input (W)
IP: International Protection Rating
t°a : Maximum ambient temperature (°C)
t°c: Maximum external temperature of the unit (°C)
Net weight (kg)
The minimum distance between a flammable material and the lighting unit (m)
Color temperature version :
CW = Cool White
WW = Warm White
NDW = Neutral Daylight White
Serial number
Replace broken glass
Class 1 product label
Read manual first label
European conformity label
WEEE directive label
EN62471 – Risk group
CEI-TR-62778 – Do not stare at light source

Units :

Weight = kilogram (kg).
Intensity = Ampere (A).
Voltage = Volt (V).
Frequency = Hertz (Hz).
Temperature = degree Celsius (°C).

ROBERT JULIAT 1166 300W LED Followspot-FIG-40

Accessories included

Optional accessories

Set-up

Mechanics

Operating positions

Minimum distance between a flammable material and the lighting unit ROBERT
JULIAT 1166 300W LED Followspot-FIG-36

Instructions for use

Lifting

Net weight: 20 Kg (44,1 lbs).

Stand set-up

Compatible stands: GT800 & GT1000
Please refer to the relevant user manual for further details.

Electrical information

LED source

Never touch or scratch the LED surface.
Cf. EN-19, 6.1.4 LED cleaning procedure if cleaning is necessary.

Power supply

Power cable

Power on

DATA

DATA connectors

Integrated terminal plug:
If no XLR connector is detected on DMX OUT connector, a 120Ω terminal plug is automatically activated. Additional terminal plug on the last unit is not necessary.

Wireless DMX option

Accessories

Iris

Gobo holder

Colour changer unit – push-pull

Operations

Light intensity

Range

Control

ROBERT JULIAT 1166 300W LED Followspot-
FIG-22

HTP mode (Highest Takes Precedence):
Light output is the highest value of DMX512 command or local control

Focus mode: when standby screen displayed,

Push Exit → Light output = 100% for 1 minute
2x times Exit → Light output = 0%
Local control → via rotary knob

Parameters

Resolution (MODE):

Curve (LIGHT CURVE): Linear / Square

Smoothing (SMOOTHING) :

Master mode (MASTER CONTROL):
In order to supervise the operator from the console, a 3rd DMX channel is used: Master control. This channel limits the maximum value of the dimmer shutter. By using this function, it’s possible to obtain synchronized fades with several spots or to give intensity limits (minimum and maximum) to the operator . Master is only active when DMX is detected. ROBERT JULIAT 1166
300W LED Followspot-FIG-18

Mode required when simultaneous remote and local control are necessary (example: follow spot)

Beam size adjustment

Range

Control

Strobe

Range

Control

Pan / Tilt

Range

Control

Iris

Range

Irising

Control

Gobo

Range

Color

Fixed color: place dark colors towards the rear end.

Range

DMX Controls

Control board

Display and Controls

Menus and parameters

Please scan this QR-Code for the software menu or go to :
www.robertjuliat.com/productSearch.html to find the latest version. ROBERT JULIAT 1166 300W LED Followspot-
FIG-6

DMX chart

Reset

Reset to default settings:
Menu: Fixture Reset → press Select → Yes & press Select to validate

Feedback information

DMX and system LED feedback (see display & controls 7 , Cf. EN-15):
- ⇒ Green= DMX512 frame detected
- ⇒ Red = Problem on DMX512 frame and/or system default – details available in the fixture status
If DMX512 data lost, the following message is displayed:
- “Push select to reset DMX values”
The last received DMX values are stored but it is possible to inactivate the current values by pressing the Select key (as well as the Master function) in order to get a total control of the fixture locally. When a DMX signal is detected, the DMX control is active again.
- ¥ signal indicates a wireless DMX:

Service

Preventive maintenance

Frequency
General maintenance should be performed at least once a year or more frequently if the equipment is operated in adverse conditions (smoke, heat, humidity, touring, etc.).

General cleaning

Remove dust from the unit (air vents, printed circuit boards, etc.).

During cleaning:

LED is protected by a safety glass to avoid any contact. DO NOT spray directly onto the glass.
Fan blades must be locked.

General visual check

No trace of heat.
No loose contacts.
No missing parts.
Tighten mechanical assemblies (screws, bolts and nuts, ground connections, etc.).

LED source

Do not touch the surface of the LED source (no contact with your hands or any tools).
Do not put compressed air directly on the source.
Contact a certified RJ distributor in case of residuals or other objects located on the surface of the LED source.

Optics
The cleaning of optical parts (lenses) shall be carried out with solutions containing alcohol.

Analysis
If there is still a problem after the troubleshooting procedures (Cf. section 7), contact RJ distributor with the following information:

Model, version and serial number of the product.
Software version (available in menu Fixture Status → Version)
Description of the problem.

LED reaction according to LED temperature

LED intensity dims to zero output (overheating protection). DMX and system LED feedback (7) is red and temperature is available in Fixture Status menu.

Thermal protection

In case of thermal protection start :

Remove the LED compartment (Cf. 6.1.4 ).
Control possible overheating indications.
Reassemble the LED compartment.
Reset the thermal protection by pressing the button.

Adjusting the maximum light output level
The maximum intensity level of the LED source can be adjusted through the fixture setup in order to have a consistent fixture fleet. The dimming level is then recalculated depending on the limitation.