FIRElood LH30-2 NEW Wood Burning Kit Instruction Manual

FIRElood LH30-2 NEW Wood Burning Kit

IMPORTANT SAFEGUARDS

WARNING :

1. Warnings must be followed carefully to avoid body injury. improper use may result in electric shock, fire.personal injury, and other damage:
2. Keep unplugged when moving the machine.
3. Keep unplugged when installing accessories.
4. Place on a flat and stable platform and operate under ventilated conditions.
5. Wear special protective equipment when operating the machine.
6. Do not use this machine in a hazardous location.
7. Only use it when the machine is working correctly.
8. Do not disassemble and repair this machine.
9. Do not use an unsuitable AC outlet.
10. Do not touch the heating plate when the machine heating.
11. Do not use in humid environments or in contact with water. Also, do not infiltrate liquid in the machine to prevent fire or electric shock caused by a short circuit.
12. Do not use the power supply that does not meet the rated voltage. The power supply that does not meet the specified voltage may cause fire or electric shock.
13. Ensure that the machine is grounded so as not to cause harm to body.
14. Do not touch the rotating rod or bearing part with your fingers during use in case of injuries.
15. If the machine is not in use for a long time, please unplug the power cord from the socket.
16. Do not use the machine during thunderstorms or lighting to avoid damage to the machine.
17. Place the machine smoothly on the flame-retardant table and keep away from flammable and explosive items.
18. Please stop using it if the machine smokes, emits a peculiar smell, or becomes noisy and in other abnormal conditions.
19. This appliance can be used by children aged 8 years and above and persons with reduced physical.sensory or mental capabilities or lack of experience and knowl­edge if they have been given supervision or instruction concerning use of the appli­ance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
20. Type Y attachment: If the supply cord is damaged, it must be replaced by the manu­facturer, its service agent or similarly qualified persons in order to avoid a hazard.
21. In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this ap­pliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
22. In the process of temperature adjustment, there will be a slight delay in the digital display temperature, which is a normal phenomenon, please wait a moment.

SAVE THESE INSTRUCTIONS

Instruction Manual of LH30-2 Pyrography Machine

1. Pyrography machine switch: Turn on 84 the switch when using it, and turn it off when not in use to avoid danger.

2. Temperature regulator: is to adjust the temperature of wood burning pen, low temperature rendering to adjust the temperature in the light gray area, the red area is the high temperature area, the high temperature area is mainly the line painting effect.
   The adjustment of the temperature of the wood burning pen is slowly adjusted by the thermostat, first of all, the temperature is adjusted to about 600 degrees and then slowly adjusted to a lower place, the best temperature is about 300-500 degrees. Low tempera­ture rendering is best used in the range of 250-400 degrees. When rendering tempera­ture adjustment, watching wood burning pen can burn light colors on the material, the temperature at this time is the best rendering effect (different material density and hu­midity need different optimal temperatures, please be patient to debug). You can draw the color painting with different shades and layers over and over again. If the tempera­ture is too high, it is difficult to render the delicate picture effect. When tracing the line, the temperature can be appropriately increased, and smooth lines can be drawn accord­ing to your own situation. If you want to bake the line well, you should learn to slow down the pen at low temperature. The lower the temperature of the burning wood used, the slower the writing pen, the better the painting effect.

3. Thermometer : The temperature of the pyrography machine is adjusted by adjusting the Tem­perature value,and the temperature adjustment display range is 250-700 degrees.

4. pyrograph pen socket:T wo with dual port configuration,press the button to quickly change pens. The pyrograph pen plug should be closely matched with the socket,the plug should be in­serted into the bottom of the socket, which should be closely matched to avoid overheating and burning accessories.

5. Conversion switch: When using the A-point wood burning pen, press I and the A-point wood-burning pen will be powered on and immediately generate heat. When using the B-point wood burn­ing pen, press II, and the B-point wood burning pen will be powered on and immediately generate heat.

Note for pyrography machine

1. Tighten the screw of the pen tip when applying the pen tip, avoid poor contact between the pen tip and the terminal so that the pen tip is not hot.The overheating of the terminal will burn out the ac­cessories, If the terminal is too hot, that is the pen tip is not tightly fastened, and it should be fas­tened with a screwdriver in time.
2.  Select a heating wire under 1 mm as the pen tip. Do not choose other non-heating wire materials such as iron wire as the pen tip,which is very dangerous and easy to bum out all the accessories in the movement, and it is easy to cause electric shock and fire.movement, and it is very easy to get electric shock and fire.

Instructions for using the wood-burning wire tip

1. The function of the bent shape wire pen tip is introduce
   Tips for using a bent metal wire pen tip. The main function of a bent pen tip is to trace lines and render small areas of silk hair. When tracing lines, the blue indi- cator on the temperature control knob points towards around 250C-350C. Slowly move the pen and do not move too fast. Look at the smooth edges of the line color, and the entire line color should be uniform and just right. When rendering, adjust the temperature to around 220C-300 °C, and draw hair fine lines at a temperature of around 250 °C -350C.

2. Pointed flat shape of metal wire pen head function introduction Tips for using pointed metal wire pen tips: Pointed pen tips mainly focus on drawing fine lines and rendering fine parts. The temperature for drawing fine lines is 220-250 °C, and the temperature for rendering fine parts is 220-230 °C. When rendering, it is best to watch the color change slightly on the gourd and wooden board, and gradually deepen the color so that the color is delicate and rich. Dark color rendering is best at around 300 °C.

3. Flat shape wire pen tip function introduction
   The flat metal wire pen head is mainly used for flat rendering and side silk line drawing. The temperature for flat rendering is around 220C-290 °C for light colors, and 300C-400 °c for dark colors.
   Summary: The temperature of the pen head introduced earlier should not be too dogmatic and rigid. Depending on the density, humidity, and hardness of the material used for soldering, the temperature required for soldering may vary. You can learn from and adjust the experiment flexibly to find the most suitable temperature for yourself. Whether it’s writing, tracing, or rendering, if you want good results, you would rather use the pen slowly at low temperatures to deepen layer by layer, Never use a pen quickly at high temperatures. It is diffi­cult to see works with uneven lines, uneven rendering colors, uneven depth, rough and delicate images.

Correct installation of pen point of pyrography

The pen point of pyrograph is not hot, and the temperature is suddenly high, and suddenly low. There are sparks coming from the pen point and the penholder is hot to grasp. What are the reasons? It’s because the incorrect installation of the pen point.

1. Unscrew both screws on the pen and detach them from the hole where the pen head is installed, making it easier for the pen head to be inserted smoothly to the bottom. The effect is shown in the above picture.

2. The picture above correctly shows the effect by inserting the two pins of the pen tip into the bottom of the hole inside.
   

3. Finally, tighten the two screws with appropriate torque, be sure to tighten.

4. Screw does not hold pen tip two pins, error! The pen tip does not heat up properly.
   

there are some symptoms of the incorrect installation of pen point , which are the abnormal heat of pen point , unstable temperature of pen point, sparks generating from the pen point, the heating of copper column and the burning hot of pen holder.

Tips for using wood burning pen tips

Tips for using wood burning tools and knives

1. This is a rendering of the wood burning just now. Later, we will demonstrate the usage techniques with a carving knife.

2. Use a carving knife to scrape off un- wanted images or defects. When scrapins genty capotnd possble.
   

3. Techniques such as using a carving knife to scrape out highlights, fine lines, and increase the brightness of local color tones in the image

1. Use tweezers to clamp and adjust the angle of the pen head. The default temperature to the highest. When the pen head turns red and has good plas- ticity, use tweezers to clamp and bend the angle of the pen head.
2. When replacing the pen tip, it is very hot and can easily burn the skin. It is safer to replace it with tweezers.

Technical data

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>