Lamerge Living Room Sectional Couch with Storage Ottoman Instruction Manual

Lamerge Living Room Sectional Couch with Storage Ottoman

Product Information

Specifications:

• Product: Sectional Sofa
• Components: Chaise Lounge, Chaise Lounge Backrest, Sofa Seat Backrest, Sofa Seat, Sofa Seat Armrest, Ottoman, Sofa Legs, Sofa Bolt
• Quantity: Chaise Lounge (X1), Chaise Lounge Backrest (X1), Sofa Seat Backrest (X1), Sofa Seat (X1), Sofa Seat Backrest (X1), Sofa Seat Armrest (X1), Ottoman (X1), Sofa Legs (X12), Sofa Bolt (X8)

FAQ

• Q: Where can I find the assembly instructions for the Sectional Sofa?
  • A: The assembly instructions are typically included in the packaging of the product. You can also refer to the user manual or contact customer support for assistance.
• Q: Can I disassemble the Sectional Sofa for moving purposes?
  • A: Yes, you can disassemble the sofa following the reverse steps of the assembly instructions. Make sure to keep track of all parts and hardware for reassembly.

General Guidelines

• Please read the following instruction carefully and use the product accordingly.
• Please keep this manual and hand it over when you transfer the product.
• This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.

Warning

• During assembly, keep all small objects out of the reach of children, as they may be fatal if swallowed or inhaled.
• Never allow children to climb or play around the product to protect children from injury caused by the tilting of the product.
• To avoid the potential dangers of suffocation, please keep all parts and packaging away from children.

Components

ATTENTION

1. When you begin each step, please check carefully whether you have taken the correct parts, so as not to use the wrong parts and cause the wrong assembly.
2. We recommend that you do not rush to tighten the screws. It is best to tighten the screws to two-thirds first, after all the steps are installed and the position is well adjusted, then tighten each screw in turn.

Installation Instructions

Step 1

• Remove legs and hardware from the zip compartment underneath he part A Body.
• During the assembly, please first half-tighten all the screws into the holes.
• After all the screws are set, fully tighten them.

Step 2

Step 3

Step 4

Step 5

Step 6

Tips

1. The armrests, support legs and hardware package of the sofa are stored in a zippered compartment underneath the sofa.
2. Manual measurement has been used, there may be some reasonable error.
3. Due to factors such as display equipment and shooting environment, the color of the item may be slightly different from the picture, which is a normal phenomenon, please refer to the actual item.

Precautions

Notes

• The product is intended for indoor use only. The product must be assembled and used under the provisions of the manual. Personal injury and/or damage to the product may occur if products are used outside of their intended purposes and/or if products have been changed/modified from their original design.
• The seller does not assume any responsibility or liability concerning any injury/damage caused by incorrect assembly or improper use.
• Avoid long-term exposure to humid environments to prevent mildew.
• Keep the product away from fire sources and high temperatures.
• Do not expose the product to direct sunlight.
• Do not place any hot objects on the surface of the product.
• If there are any defective or missing parts after unpacking, please cease assembly immediately and contact us.
• Please assemble the item on a spacious surface and do not place the unwrapped product directly on the ground to avoid product damage
• Please do not stand or sit on the wooden boards.
• Please wear gloves during the assembly and/or disassembly process to avoid scratches from any sharp edges.
• Please match the corresponding part and fitting based on the part number in the manual.
• If the part does not match with the fitting, please check the piece as specified in this manual.
• During assembly, first loosely align all screws with the corresponding pre-drilled holes and then tighten the screws one by one.
• Periodically inspect screw tightness while the product is in use. If necessary, retighten to ensure structural integrity.
• If you accidentally spill water or another liquid on the surface, immediately wipe clean with a dry towel.
• Please keep the product away from sharp, pointed objects and corrosive substances to prevent product damage. Please place this item on the level solid ground during use.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>