LiftMaster 882LMW Multi Function Wall Station Instruction Manual

: June 1, 2024
: LiftMaster

Table of Contents

LiftMaster 882LMW Multi Function Wall Station
UNATTENDED OPERATION
INSTALLATION
PROGRAM
FEATURES
MAINTENANCE ALERT SYSTEM (MAS)
WARRANTY
FCC STATEMENT
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LiftMaster 882LMW Multi Function Wall Station

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:
Be sure the power is NOT connected BEFORE installing the door control.
Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
Install door control within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of the door.
NEVER permit children to operate or play with door control push buttons or remote control transmitters.
Activate the door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
ALWAYS keep the garage door in sight until completely closed.
NEVER permit anyone to cross the path of closing the garage door.
Unattended devices and features are to be used ONLY with sectional doors.

For use with Security+ 2.0° Garage Door Openers, Wi-Fi® enabled Security+ 2.0* Garage Door Openers (indicated by the Wi-Fi logo on the garage door opener cover) and MyQ® accessories.

UNATTENDED OPERATION

The Timer-to-Close (TTC) feature, the MyQ® Smartphone Control app, and MyQ® Garage Door and Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to close without being in the line of sight of the door is considered unattended close. The Timer-to-Close (TTC) feature, the MyQ® Smartphone Control, and any other MyQ® devices are to be used ONLY with sectional doors.

INSTALLATION

Unplug the garage door opener. Disconnect the battery (if applicable).

Connect the wires to the back of the door control.
Secure the door control to the wall.
Connect the wires to the garage door opener.

Plug in the garage door opener and reconnect the battery. The command LED on the door control will blink if installed correctly. To synchronize the garage door opener and the door control, press the push bar up to 3 times, until the garage door opener activates.

LiftMaster-882LMW-Multi-Function-Wall-Station-fig-1.

PROGRAM

REMOTE CONTROL

Press the LEARN button on the door control twice. The Command LED will blink.
Press and release the button on the remote control that you wish to operate your garage door.

The garage door opener lights will flash (or two clicks will be heard) and the Command LED will stop blinking when the code has been programmed.

KEYLESS ENTRY

Press the LEARN button on the door control twice. The Command LED will blink.
Enter a 4-digit personal identification number (PIN) on the keypad. Then press the ENTER button.

The garage door opener lights will flash (or two clicks will be heard) and the Command LED will stop blinking when the code has been programmed.

CONNECT YOUR GARAGE DOOR OPENER TO YOUR HOME WI-FI® NETWORK (for Wi-Fi garage door openers ONLY)

LiftMaster-882LMW-Multi-Function-Wall-Station-fig-5

Lift the push bar on the door control. Press and release the LEARN button. The garage door opener will beep once and the command LED on the door control will blink to indicate Wi-Fi learn mode. You have 20 minutes to complete the connection process.
On your mobile device, go to Settings > Wi-Fi and select the network with the “MyQ-” prefix.
Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com into the browser address bar. Follow the on screen prompts to connect the garage door opener to your Wi-Fi network. The MyQ serial number will display on screen. Write the serial number in the space below.
Download the MyQ app from the App Store® or Google Play™ store. Sign up for your MyQ account and add the MyQ serial number to your account.

If you are unsuccessful in adding your device, try an alternate web browser or visit WiFiHelp. LiftMaster.com.

FEATURES

LiftMaster-882LMW-Multi-Function-Wall-Station-fig-6

LOCK

Prevents activation of the garage door opener from remote controls while still allowing activation from the door control and keyless entry. Factory default is OFF.
Turn ON: Press and hold the LOCK button for 2 seconds. The command LED will blink as long as the lock feature is activated.
Turn OFF: Press and hold the LOCK button again for 2 seconds. The command LED will stop blinking and normal operation will resume.

LIGHT
Press the LIGHT button to turn the garage door opener lights on or off.
The LIGHT button will not control the lights when the door is in motion.
When the lights are turned on they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after a specified period of time (see below).
TO CHANGE THE AMOUNT OF TIME THE GARAGE DOOR OPENER LIGHTS WILL STAY ON
Press and hold the LOCK button until the garage door opener lights flash (about 10 seconds). The garage door opener lights will flash up to 4 times to indicate current setting:

Flash = Lights stay on 1 ½ minutes
Flashes = Lights stay on 2 ½ minutes
Flashes = Lights stay on 3 ½ minutes
Flashes = Lights stay on 4 ½ minutes (factory default)

Repeat the steps above until your desired time frame is reached.
LIGHT FEATURE FOR THE SAFETY REVERSING SENSORS The garage door opener lights will turn on when the safety reversing sensor beam is interrupted. Factory default is ON.
Turn ON: Start with the garage door opener lights on. Press and hold the LIGHT button to turn off the light, continue to hold until the light turns on (about 10 seconds).
Turn OFF: Start with the garage door opener lights off. Press and hold the LIGHT button to turn on the light, continue to hold until the light turns off (about 10 seconds).

MAINTENANCE ALERT SYSTEM (MAS)

When the garage door opener needs to be serviced (approximately 4500 garage door opener cycles) the command and service LEDs will alternately blink back and forth. Factory default is OFF.
Turn ON/OFF: Press and hold the LEARN button. Then press the LIGHT button. The service LED will blink the status; ON is 2 blinks and OFF is 3 blinks.

WARRANTY

ONE-YEAR LIMITED WARRANTY
LiftMaster warrants to the first consumer purchaser of this product that it is free from defects in materials and/or workmanship for 1 year from the date of purchase.

FCC STATEMENT

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustments or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER-SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.