Ronix 5304 255mm Single Bevel Sliding Miter Saw Instruction Manual
- June 1, 2024
- Ronix
Table of Contents
255mm SINGLE BEVEL SLIDING MITER SAW
5304
TECHNICAL SPECIFICATION
| Model | 5304 |
|---|---|
| Power | 1800W |
| Voltage | 220-240V |
| Frequency | 50-60Hz |
| No load speed | 5200RPM |
| Disk diameter | 255mm |
| Max Cutting Capacity at 0°/90° | 320×89mm |
| Max Cutting Capacity at 45°/90° | 210×89mm |
| Max Cutting Capacity at 0°/45° | 320×42mm |
| Max Cutting Capacity at 45°/45° | 210×42mm |
| Weight | 14.4Kg |
| Includes | Wrench, Carbon brush, Dust Bag, Vise Screw, Angle Handle, Extention |
Board.
PART LIST
- Handle
- On/Off Switch
- Movable Gurad
- Laser Switch
- Fence
- Movable Base
- Adjustment Handle
- Base Locking Holder
- Gradinet Base
- Fixed Base
- Holder
- Sliding Base
- Movable Fence
- Release Locking Handle
- Sliding Lever
- Fixed Guard
Safety is a combination of common sense, staying alert and knowing how your compound miter saw works.
WARNING!
TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY, DO NOT PLUG IN THE SAW
UNTIL THE FOLLOWING STEPS HAVE BEEN READ AND UNDERSTOOD.
1- Read and become familiar with this entire instruction manual. learn the
tool’s applications, limitations, and possible hazards.
2- Avoid dangerous conditions. Do not use power tools in wet or damp areas or
expose them to rain. Keep work areas well lit.
3- Do not use power tools in the presence of flammable liquids or gases.
4- Always keep your work area clean, uncluttered and well-lit. Do not work on
floor surfaces that are slippery with sawdust or wax.
5- Keep by standers at a safe distance from the work area, especially when the
tool is operating. never allow children near the tool.
6- Do not force the tool to do a job for which it was not designed.
7- Dress for safety. Do not wear loose clothing, gloves, neckties or jewelry
(rings, watches) when operating the tool. they can get caught and draw you
into moving parts always wear non-slip footwear. And tie back long hair.
8- Wear face mask or dust. Sawing operation produces dust.
9- Always remove the power cord plug from the electrical outlet when making
adjustments, changing parts, cleaning or working on the tool.
10- Keep guards in place and in working order.
11- Avoid accidental start-UPS. Make sure the power switch is in the OFF
position before plugging in the power cord.
12- Remove adjusting tools. Always make sure all tools are removed from the
saw before turning it on.
13- Never leave a running tool unattended. Turn the power switch to OFF Do not
leave the tool until it has come to a complete stop.
14- Never stand on a tool. Serious injury could result if the tool tips or is
accidentally hit. Do not store anything above or near the tool.
15- Do not overreach. Keep proper footing and balance at all time. Wear oil-
resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other
debris.
16- Maintenance tools Properly. always keep tools clean and in good working
order. Follow instructions for lubricating and changing accessories.
17- Check for damaged parts. Check for alignment of moving parts, jamming,
breakage, improper mounting, or any other conditions that may affect the
tool’s operation. any part that is damaged should be properly repaired or
replaced before use.
18- Make the workshop childproof. Use padlocks, master switches and always
remove starter keys.
19- Do not operate the tool if you are under the influence of drugs, alcohol
or medication that could affect your ability to use the tool properly.
Documents / Resources
|
Ronix 5304 255mm Single Bevel Sliding Miter
Saw
[pdf] Instruction Manual
5304, 5304 255mm Single Bevel Sliding Miter Saw, 255mm Single Bevel Sliding
Miter Saw, Single Bevel Sliding Miter Saw, Bevel Sliding Miter Saw, Sliding
Miter Saw, Miter Saw, Saw
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>