Lansinoh ‎53050 Double Electric Breast Pump User Manual

Lansinoh ‎53050 Double Electric Breast Pump

Intended Use of Breast Pump

• The Lansinoh® Signature Pro® Double Electric Breast Pump is intended to express and collect the breastmilk of a nursing woman for the purpose of feeding collected breastmilk to a baby. The Signature Pro® is intended for a single user.

Indications of Breast Pump

• Lansinoh® Signature Pro® Double Electric Breast Pumps are indicated to eliminate of clinical situations such as milk stasis in the breast, engorgement and mastitis caused by insufficient milk discharge, relieve sore and cracked nipples, and to bring out flat or inverted nipples. Also,
• Lansinoh® Signature Pro® Double Electric Breast Pumps enable mothers to provide breast milk for babies who cannot feed directly at the breast for a variety of reasons, such as latch-on problems, and premature or unwell babies.

Contraindications of Breast Pump

• There are no known contraindications.

Important Safeguards

The Lansinoh® Signature Pro® Double Electric Breast Pump is a personal care item and for hygienic reasons should never be shared between mothers or resold from one mother to another. Either of these actions will void the warranty. If you are a mother who is infected with Hepatitis B, Hepatitis C or Human Immunodeficiency Virus (HIV), pumping breastmilk using the Lansinoh® Signature Pro® Double Electric Breast Pump will not reduce or remove the risk of transmitting the virus to your baby through your breastmilk.

When using electrical products, especially when children are present, basic safety precautions should always be maintained, including the following:

Read All Instructions Before Using

Danger: To reduce the risk of electrocution:

• Always unplug this product immediately after using it.
• Do not use it while bathing.
• Do not place or store this product where it can fall or be pulled into a tub or sink.
• Do not place or drop the pump into water or other liquid.
• Do not reach for an electrical product that has fallen into the water.
• Unplug immediately.

Warning: To reduce the risk of burns, electrocution, fire, or injury to persons:

• This product should never be left unattended when plugged in.
• Close supervision is necessary when this product is used near children.
• Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
• Never operate this product if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water.
• Keep the cord away from heated surfaces.
• Never use it while sleeping or drowsy.
• Never drop or insert any object into any opening or tubing.
• Do not use this product if it is broken or any parts are missing.
• Do not allow small children or pets to play with the pump unit, AC adapter, etc.
• Do not use outdoors with the AC adapter or operate where aerosol spray products are being used or where oxygen is being administered.

Save These Instructions along with your receipt for future reference. Submit warranty card online at Lansinoh.com/warranty

Congratulations!

Your decision to provide your baby with breastmilk, even if you need to be apart, is one of the most precious gifts you can give your baby. The Lansinoh® Signature Pro® is a safe, efficient, and effective choice for moms who need to pump regularly.

PLEASE DO NOT RETURN THIS PUMP TO THE RETAILER.

Lansinoh’s dedicated Customer Service team is here to help. If you experience any issues with your Lansinoh® Signature Pro® breast pump please call 800-292-4794 or email customerservice@lansinoh.com, Monday – Friday 8am-8pm EST.

QUICK START GUIDE

Do NOT wash or sanitize tubing

Before first use, sterilize all parts that will come into contact with milk according to instructions on pg 8, section 3.1.

Please carefully read all instructions prior to use

Assembly

See detailed instructions on pgs 9-11. Proper assembly is essential to ensure proper function and suction.

Connect pump to power using AC Adapter or six AA Alkaline Batteries (not included)

Getting Started

Hold Breastmilk Expression Set to your breasts so that the nipple is aligned to extend straight toward the nipple tunnel of the breast flange, ensuring there are no gaps for air to enter. Make sure set is tilted slightly downward to allow milk to flow into bottles.

2-Phase Technology – Using Let-Down and Expression Phases

• Press the power button to start the pump in the let-down phase .
• The let-down phase will run automatically for two minutes.
• To begin the expression phase sooner, press the Let-down/Expression Toggle button to move to the expression phase. Press the Let-down/Expression Toggle button again at any point to switch back to the Let-down phase.

Customization for Comfort and Efficiency

Pumping Style Selection

Every baby feeds differently. The Signature Pro® offers three different pumping styles to choose from, allowing you to choose the option that is most like your baby’s feeding patterns. Change the pumping style using the Style Mode Toggle button to find the pumping style that works best for you.

NOTE: When you switch to the expression mode the pump will start in Style 2.

Adjusting Suction Levels

Increase or decrease the suction to the maximum level that you find comfortable.

• Increase suction by pressing the button.
• Decrease suction by pressing the button.

Lansinoh® is here to support you. If you have questions, please do not hesitate to contact us at 800-292-4794

PARTS DIAGRAMS

Basic Controls, Display and Features

1. Power, On/Off button
2. Suction Level Increase Control Button
3. Pumping Style Toggle Button
4. LCD Display
5. Let-Down/Expression Toggle Button
6. Suction Level Decrease Control Button
7. Let-Down/Expression Phase Indicator
8. Time Display
9. Pumping Style Indicator
10. AC Power Indicator
11. Battery Power Indicator
12. Suction Level Indicator
13. Tubing input
14. Battery compartment for 6 AA batteries (not included)
15. AC adapter input

AC Adapter

Lansinoh® Signature Pro® Breast Pump Parts

Item: Item Number

• A. Signature Pro® Tubing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #53458
  • A1 Silicone Tubes 300 mm (2)
  • A2 Silicone Tube 600 mm
  • A3 Signature Pro® Tubing Y Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53405
  • A4 Signature Pro® Tubing Strap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #50417
  • A5 Signature Pro® Pump Connnector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53453
• B. Breastmilk Expression Set Includes:
  • B1 ComfortFit® Breast Flange 25mm (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53408
  • B2 Signature Pro® Breast Flange Body (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53454
  • B3 Signature Pro® Diaphragm (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53402
  • B4 Signature Pro® Diaphragm Cap (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #53410
  • B5 White Valve (2 + 2 extra). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #53400
  • B6 5 oz (150 ml) Bottle (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #53451
• C. Storage Lids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53450
• D. Signature Pro® AC Adapter/power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#53409

Two extra white valves are included. Larger size flanges are sold separately. To order replacement parts or larger size flanges please visit www.lansinoh.com/store.

CLEANING INSTRUCTIONS

Unless otherwise instructed by your healthcare provider, follow these sanitizing and cleaning instructions.

• Do not boil or wash tubing or connector!
• When sanitizing parts, use enoughwater to keep parts afloat!

Before First Use of Breastmilk Expression Set

• Prior to using the set for the first time, disassemble and boil all parts of the Breastmilk Expression Set that come into contact with breastmilk for 5 minutes.
  • Ensure you use enough water to keep parts afloat while boiling.
  • Do not boil the tubing and tubing connector. The Lansinoh® Signature Pro® is a hygienic, closed system design, which ensures breastmilk will not enter the tubing or motor.
• Remove all parts from water immediately after boiling, using caution as parts will be hot.
• Completely air dry before assembly and use. Partially dried parts may affect operation of the pump. Please ensure parts are completely dry before use.

Cleaning of Breastmilk Expression Set

• Set aside the tubing and tubing connector.
• The breast flange and bottles may be cleaned in the upper rack of your dishwasher or hand washed with dish soap in hot water. For best results, we recommend using a baby bottle brush to clean the bottle and a baby nipple brush to clean the insides of the breast flange. DO NOT use
• solvents or abrasives. Rinse with hot, clean water.
• All other parts of the Breastmilk Expression Set should be hand washed to prevent loss and to extend their usefulness.
• To clean your breast pump base, wipe with a damp cloth, using only water or mild soap.

Before Each Use of Breastmilk Expression Set

• Always wash hands thoroughly with soap and water before handling the Breastmilk Expression Set, the pump body, or other attachments.
• Ensure that the tubing is free of any liquid or moisture. Do not operate the pump if liquid or moisture is visible in the tubing.
• Ensure diaphragms are completely dry before use.
• Before each use, visually inspect the individual components for cracks, chips, tears, discoloration or deterioration, as this may affect the functionality of the Breastmilk Expression Set. Please visit www.lansinoh.com/store or call 1-800-292-4794 for further guidance and replacement parts.

WARNING: It is highly recommended not to use any method other than the above mentioned cleaning methods.

WARNING: Use caution when cleaning the small white valve. It is important for proper suction. Do not use excessive force and do not clean with a baby bottle brush or a nipple brush. Gently wash by hand in hot, soapy water and rinse under hot running water.

To use steam or microwave sterilisers: Follow the manufacturers instructions. Ensure all openings are face down in the steriliser. Ensure you wash your hands before removing equipment from the steriliser.

ASSEMBLY

Assembling the Breastmilk Expression Set

1. Place purple silicone diaphragm, the feet down, on the top of flange body. Ensure diaphragm fits securely between rims of breast flange body.

2. Place clear diaphragm cap over breast flange body and twist to secure so that the tubing portal is facing the back of the pump.

3. Firmly push ComfortFit® Flange into breast flange body.

4. Holding the base of the white valve, gently secure the valve into the bottom of the breast flange body.
   NOTE: Use care when handling and cleaning the small white valve.

5. Screw collection bottle onto breast flange body.

6. Attach end of 300 mm tubing to back of diaphragm cap. Ensure that tubing is pushed all the way to the base of the attachment port and completely covers it.

7. Attach other end of 300 mm tubing to Tubing Y Connector.

8.  Repeat assembly process for second breast flange body.

Connecting the Breastmilk Expression Set

Once Breastmilk Expression Set is assembled, connect to pump base:

1. Secure one end of 600 mm tubing to Tubing Y Connector.
2. Secure other end of 600 mm tubing firmly to the pump connector.
3. Insert pump connector into opening on left side of pump.

Connecting for Single Pumping

1. Remove one of the 300 mm tubing from the Tubing Y Connector.
2. Secure plug into open outlet of Tubing Y Connector.

USING THE LANSINOH® SIGNATURE PRO® DOUBLE ELECTRIC BREAST PUMP

Power Options

The pump may be operated using the following power supply modes:

AC Adapter

1. Connect the AC adapter to the power receptacle located on the right side of the pump. Plug the AC adapter into an available electrical outlet.
2. Electrical safety can only be achieved when the breast pump is connected to the AC Power adapter supplied with the product. (See “Technical Data” section, page 18)

AA Alkaline Batteries (not included)

• Make sure the batteries are inserted correctly according to the polarity (+) and (-) as indicated.
• Close the compartment by gently pressing the cover until it snaps into place.
  • Remove batteries if pump is not in use for a long period of time.
  • Dispose of batteries according to regulations for environmental protection and recycling.
  • Replace batteries as a simultaneous set. Do not mix old and new batteries.
  • Do not mix alkaline and standard (carbon-zinc) batteries.
  • If batteries are in the pump, but AC adapter is in use, the pump will use the adapter to power the pump, not the batteries.

For the most economical use, we recommend using your pump with the AC adapter provided. Your AC adapter is a universal AC plug adapter type and can be used with 100 VAC to 240 VAC systems with 50Hz and 60Hz mains.

Getting Started

If possible, wait until your breastmilk supply and breastfeeding schedule are well established. This is normally at least 3-4 weeks after birth, unless told otherwise by your doctor or breastfeeding advisor.

1. Hold the Breastmilk Expression Set to your breasts so that the nipple is aligned to extend straight toward the nipple tunnel of the breast flange.
2. Make sure the breast completely fills the breast flange so that a vacuum is formed and no air escapes.
3. The Breastmilk Expression Set and nipple tunnel must tilt slightly downward to allow milk to flow naturally toward the bottle.

If you experience friction or discomfort on your nipples, you may need a different size flange. Larger size flanges are available. For more details, please call 800-292-4794 or visit lansinoh.com/store.

2-Phase Technology

Using Let-Down and Expression Phases

1. Press and hold the On/Off Button to turn the pump on. The Lansinoh® Signature Pro® Double Electric Pump will start in the Let-Down Phase.
2. After two minutes, the Let-Down Phase will automatically change to the Expression Phase in Cycle Mode 2.
3. If you prefer to bypass the pre-set two minute Let-Down Phase or your milk lets-down sooner than two minutes, press the Let-Down/Expression Toggle Button to move to the Expression Phase.
4. The Style Mode Indicator will appear in the display to signify that you are in the Expression Phase.

Customization for Comfort and Efficiency

Using Customizable Pumping Styles

Choose your style Each baby is unique – right down to the ways they feed. The Lansinoh® Signature Pro® offers three different pumping styles to choose from – so you can select the style that best simulates your baby’s feeding style.

1. With the pump in Expression mode, select the style that is most comfortable and efficient for you by pressing the Pumping Style Toggle Button .
2. Pressing the button again will select the next style.
3. The mode will be indicated on the LCD Display by the Style Mode Indicator. You may find that the best style for you changes over time. The customization features of the Signature Pro® allow you to adjust with you and your baby.

Tailor for comfort

Within each pumping style, there are eight levels of suction to choose from:

1. Adjust for higher suction by pressing the suction level increase control button.
2. Adjust for lower suction by pressing the suction level decrease control button.
3. The current suction level will be indicated by the number of dark bars on suction level indicator.

Note: If at any time the suction on your breast reaches uncomfortable levels, reduce the suction level by pressing the button on the left side of the LCD screen or disconnect the tubing from its receptacle on the electric pump.

Completing Your Pumping Session

1. When a pumping session is finished, turn the pump off with the on/off button.
2. After turning the pump off, the display will remain on for a few seconds.
3. Make sure there is no suction on the nipple(s) before removing the breast flanges from the breast. If necessary, break the suction by inserting a finger between the breast flangeand the breast. Once the suction is broken, the breast flange can be removed safely.

Please note: The LCD display light will automatically switch off if no control buttons are pressed for 20 seconds in order to save power. If the pump unit is left on and  unattended for more than 60 minutes, the control system will automatically poweroff. To turn unit back on, hold the power-on button for several seconds.

PUMPING TIPS

Pumping Tips

• The most important part of successful pumping is the ability to trigger the let-down reflex. This is when your milk begins to flow freely. Warm wet compresses applied to the breasts and gentle, circular massaging of the breasts prior to and/or during a pumping session can help encourage this natural reflex. Thinking of or looking at your baby, or a photo of your baby if you are apart, can also be helpful. Some moms can achieve more than one let-down during a pumping session. You may be able to achieve a second by returning to the Let-Down phase by pressing the Let-Down/Expression Toggle Button.

How Long To Pump

• Double pumping, compared to single pumping, will reduce the time you spend expressing your milk. Breastmilk is produced on a supply and demand basis. Expressing your breastmilk regularly will stimulate your body and help you maintain your milk supply. Just like with breastfeeding, it is not necessary to time your pumping sessions. As you get more experienced with pumping, you will get a better sense of the time it takes for your body to express your milk using a breast pump. If you have any breastfeeding or breastpump related questions, consult with an International Board Certified Lactation Consultant (IBCLC), breastfeeding counselor, or other healthcare provider such as your primary physician.

Pumping and Feeding Tips

• You may pump one breast while nursing the baby on the other. This allows you to maximize pumping effectiveness using the let-down reflex stimulated by your baby’s sucking.
• Always test the temperature of any liquid before feeding your baby.
• Do not let a child take a bottle to bed or self-feed for long periods.
• To prevent possible choking hazard, test strength of the nipple by pulling on the bulb portion. Discontinue use if any tear or crack appears.

TROUBLESHOOTING

Troubleshooting the Lansinoh® Signature Pro® Double Electric Breast Pump

Interruption of Electrical Service

If you experience an interruption in the normal operation of the electrical and/or mechanical functioning of the pump, simply do the following:

• Unplug the AC adapter cord from the electrical outlet.
• Wait a few seconds, and then plug the AC adapter cord back into the electrical outlet. If you still experience electrical failure, try using the pump with the six AA batteries making sure the AC adapter is removed.

Discomfort While Pumping

• If you feel any discomfort, you may need a different size flange. Visit lansinoh.com/store or call 800-292-4794.

Decreased Suction

If it feels like the suction has decreased, try the following:

• Remove the tubing from pump and place a finger over the tubing connector.
• If you feel suction, the pump is operating properly, but the Breastmilk Expression Set may not be correctly assembled or the white valve may be damaged.
• Make sure the Breastmilk Expression Set has been properly assembled. Check the assembly information in the section “Assembling the Breastmilk Expression Set,” pages 9-11.
• Inspect the white valve for a tear or pinhole. This component is critical to achieving proper suction. Replace the white valve with one of the spare valves provided with the product.
• If no suction is felt on your finger, try unplugging the adapter from the electrical outlet, wait a few seconds, and plug it back into the electrical outlet.
• When single pumping, check the tubing connector on the front of the pump to make sure it is closed for single pumping. If open, close the connector.
• If double pumping, ensure that the Breastmilk Expression Set is on both breasts before starting the pump.

Increased suction level for single pumping: If it feels like the suction is higher than usual when single pumping, check that the plug for the pipe is clean and that the airway in the plug is not blocked.

BREASTMILK STORAGE GUIDELINES

Breastmilk Storage and Thawing Guidelines for Healthy Term Babies

Check with your healthcare provider or an International Board Certified Lactation Consultant for specific storage instructions. When freezing, store in the back of the freezer and do not store milk in the door as temperature can fluctuate as the door is opened and closed.

(acceptable)
In a Refrigerator| <39°F (<4°C)| 72 hours (ideal) up to 8 days (acceptable)
Freezer| 0°F (-18°C)| 3 months (ideal) up to 6 months (acceptable)
Deep Freezer| -4°F (-20°C)| 6 months (ideal) up to 12 months (acceptable)

Source: La Leche League International 2014 Date all breastmilk and use the oldest breastmilk first.

Thawing Thaw frozen milk in the refrigerator or place the containers under cool running water, gradually warming the water until the milk is thawed. Thawed milk can be kept in a refrigerator for up to 24 hours.

NOTE: DO NOT refreeze milk once it is thawed.

Gently shake thawed milk before feeding to baby to mix the layers that have separated. Breastmilk is not homogenized and the “cream” will rise to the top of the bottle. Breastmilk can vary in color and consistency depending upon the time of the day that the milk was expressed, what you have eaten, and the age of the baby at the time of pumping.

NOTE: DO NOT MICROWAVE HUMAN MILK! Microwaving alters the composition of the milk. Microwaving also may create “hot spots” in the milk that could burn the infant.

NOTE: DO NOT thaw breastmilk in hot or boiling water.

THE LANSINOH® NATURALWAVE® NIPPLE

Clinically proven to reduce nipple confusion in breastfed babies

• Latching on Baby’s lips open outward and latch onto the areola
• Peristaltic “wave-like” tongue movement Baby’s tongue moves in “wave-like” motion to compress nipple and extract milk
• Swallowing Back of baby’s tongue rises, channeling the milk into the esophagus

The patented NaturalWave® Nipple enables baby to replicate natural sucking actions learned at the breast.Exclusive breastfeeding is recommended for at least 3-4 weeks if possible before introducing a bottle and nipple.

• Storage & Use: Prior to use, always inspect and pull the feeding nipple in all directions to check the product. Throw away at the first signs of damage or weakness. For safety and hygiene reasons, replace the nipple every 7 weeks. Before first use, boil all parts for 5 minutes to sanitize. Ensure all parts are completely covered in water and free floating.
• Cleaning: Before first use, place all components in boiling water for 5 minutes, allow to cool and thoroughly rinse all bottle components. Always wash all components of the product immediately after each use. The feeding nipple can be washed in hot soapy water and rinsed in clean water. Dishwasher safe on top rack only. Safe to clean in a microwave-safe, steam sterilizer bag and special sterilizing machine. Do not clean with solvents or harsh chemicals
• Assembly: Once thoroughly dry, insert feeding nipple through the top of the screw cap collar. Attach the screw cap collar securely onto the bottle neck. When carrying a full bottle, make sure it is closed with the collar in place, taking care to position the feeding nipple in the center of the collar to activate the “spill-proof” function of the product.
• Precautions: Do not leave bottle in direct sunlight, heat or disinfectant Bottle (sterilizing solution), as this may weaken the nipple. Do not clean with or allow feeding nipple to come into contact with solvents or harsh chemicals. Damage could result. Fill with the required amount of liquid and tighten the screw cap before using. Do NOT overfill. Heating in a microwave is NOT recommended as it may produce uneven heating and high localized temperatures. If you choose to heat liquid this way, DO NOT SEAL BOTTLES. Swirl well before use, and always check the temperature before feeding baby. Hot or unevenly heated liquid may burn baby’s mouth. Do not warm liquid by placing the bottle directly onto gas or electric rings, warming plates, in electric ovens, etc. Wash after every use. Some liquids and sterile solutions may make the silicone become opaque. This does not alter any of its properties.
• WARNING! DO NOT MICROWAVE HUMAN MILK! Microwaving alters the composition of the milk and may also create “hotspots” in the milk that could burn the infant. Allowing your child to use this product for prolonged periods separate from regular mealtimes or to go to sleep while drinking liquids, other than water, from this bottle may cause or contribute to early childhood tooth decay. Always use this product with adult supervision. Keep all components not in use out of the reach of children. Do not leave baby alone with drinking equipment due to the risk of choking. Never use feeding nipple as a pacifier or soother. Always check liquid temperatures before feeding. Packaging materials are not part of the product. For your child’s safety, please remove and discard all packaging materials prior to use but read and retain the instructions for future reference.
  Warning: Packaging materials are not part of the product. For your child’s safety, please remove and discard all packaging materials prior to use but read and retain the instructions for future reference.

TECHNICAL DATA

The expected service life of the pump is 500 hours.

Power Supply

• Battery operation: 6 AA size alkaline batteries, all connected in series
• Battery operating time: Minimum 30 minutes. Maximum 2 hours. Results are dependent on battery freshness and pump settings.
• AC Adapter operation: 100-240VAC wall plug type AC adapter, galvanically isolated with 9Vdc output voltage
• Pump power dissipation: 10.0 Watts maximum
• Voltage regulation: Linear voltage regulator with low dropout voltage and short circuit protection

Control System

• Control unit: Microcontroller with integral program memory
• Program memory: 32K flash ROM, 2K RAM memory
• HMI: LCD display with LED backlight, soft keypad
• Single / double control: Single or double breast pumping possible
• Selectable pumping rhythm mode: 3 pumping rhythm modes are selectable and controlled from keypad
• Adjustable suction level: 8 suction levels are selectable and controlled from keypad
• Suction vacuum level (Expression/Double pumping): Minimum 90mmHg, Maximum 280mmHg

Power Requirements

• AC Adapter (included)
• AC Adapter – North American

Plug Configuration

• 100-240VAC wall plug type
• AC adapter, galvanically isolated adapter with 9Vdc output voltage. Batteries (not included)
• 6 AA batteries, 1.5V alkaline

To maintain your power adapter follow these instructions:

DO NOT use power adapter if damaged.

Warning: Children have STRANGLED in cords. Keep the cords out of the reach of children.

WARRANTY

Limited Consumer Product Warranty (United States)

• This product is warranted to the original consumer purchaser (the “purchaser”) to be free from defects in material and workmanship which are not commercially acceptable for the period of one year from the date of purchase on the pump mechanism and the period  of 90 days on all other product components. Warranty coverage terminates if you sell or otherwise transfer this product to another person. This warranty gives you specific legal rights and you may also have other rights, which vary, by location.
• LANSINOH® MAKES NO EXPRESS WARRANTY OF ANY KIND REGARDING THE PRODUCT OTHER THAN THOSE WARRANTIES EXPLICITLY SET FORTH HEREIN. ANY IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY  IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT PERMITTED BY LAW, SHALL BE LIMITED IN DURATION TO A PERIOD OF 90 DAYS FROM THE DATE OF PURCHASE BY THE ORIGINAL PURCHASER.
• In the event the product is found by Lansinoh® to not meet the above limited warranty, as purchaser’s sole and exclusive remedy Lansinoh® will repair or, at the option of Lansinoh®, replace this product without charge for such replacement or parts or labor.
• NOTE: The purchaser shall bear all expense for returning this product to Lansinoh®. This warranty does not apply to any product that has been subjected to misuse, abuse, or alteration.
• Only Lansinoh® brand replacement parts are recommended for use with Lansinoh® breastfeeding products. Improper or incorrectly performed maintenance or repair, or use of non-Lansinoh® brand replacement parts may invalidate this warranty.
• TO THE EXTENT PERMITTED BY LAW, LANSINOH® SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, REPLACEMENT COSTS RESULTING FROM THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.
• If you wish to make a claim under this warranty, you must return the product to Lansinoh Laboratories Inc., prepaid, together with your dated bill of sale or other dated proof of purchase and a brief statement of the problem, along with a Replacement Authorization (RA) number. You may obtain the appropriate Replacement Authorization number and shipping address by calling the phone number or sending an email to the email address provided below.
• Items returned without an associated Replacement Authorization Number will be returned to sender.
• To obtain the address to Return Goods or a Replacement Authorization Number: 800-292-4794 or customerservice@lansinoh.com

Submit warranty card online at Lansinoh.com/warranty

DECLARATION FOR ELECTROMAGNETIC COMPATIBILITY (EMC)

For Information Use Only

Medical electrical equipment. This table is referenced from Table 9 of IEC 60601-1-2 General requirements for basic safety and essential performance. Collateral Standard: Electromagnetic disturbances – Requirements and tests

Guidance and Manufacturer’s Declaratlon – Electromagnetlc Emissions

This breast pump is intended for use in the electromagnetic environment specified below. The customer or the user of the breast pump should assure that it is used in such an environment.
Emission Tests| Compliance| Electromagnetic Environment – Guidance

RF emissions CISPRll

|

Group 1

| The breast pump uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.

RF emissions CISPRll

|

Class B

| The breast pump is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic emissions IEC 61000 -3-2| Class A|
Voltage fluctuations/flicker emissions IEC 61000 -3-3|

Not Applicable

|
Warning – This breast pump should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, this breast pump should be observed to verify normal operation in the configuration in which it will be used.
Guidance and Manufacturer’s Declaratlon – Electromagnetic Immunity

This breast pump is intended for use in the electromagnetic environment specified below.

The customer or the user of the breast pump should assure that it used in such an environment

THE LANSINOH® SIGNATURE PRO® ELECTRIC BREAST PUMP has no essential performance but was tested for immunity to electromagnetic disturbances and passed using the following criteria:

1.  No visible change in the operation of the breast pump.

2.  The breast pump changes settings but returns automatically to previous settings.

3.  The breast pump changes settings but can return to previous settings by intervention of the user.

Immunity Test| IEC 60601 Test Level| Compliance Level| Electromagnetlc Environment – Guidance
Electrostatic discharge (ESD)

IEC 61000 -4-2

| ± 8 kV contact ± 2 kV, ± 4kV, ± 8 kV, ±

15kV air

| ± 8 kV contact

± 2 kV, ± 4kV, ± 8 kV ±

15kV air

| Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Electrical fast transient / burst IEC 61000 -4-4| ± 2 kV 100 kHz repetition frequency| ± 2 kV 100 kHz repetition frequency| Mains power quality should be that of a typical commercial or hospital environment.
Surge IEC 61000 -4-5| ± 0,5 kV, ± 1 kV Line- to-line| ± 0,5 kV, ± 1 kV Line- to-line| Mains power quality should be that of a typical commercial or hospital environment.
Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11| 0% UT; 0.5 cycle At

0°, 45°, 90°, 135°,

180°, 225°, 270°

and 315°

| 0% UT; 0.5 cycle At

0°, 45°, 90°, 135°, 180°,

225°, 270° and 315°

| Mains power quality should be that of a typical commercial or hospital environment. If the user of the breast pump requires continued operation during power mains interruptions, it is recommended that the breast pump be powered from an uninterruptible power supply or a battery.
Power frequency

(50/60 Hz) magnetic field IEC 61000 -4-8

| 30A/m| 30 A/m| It may be necessary to position the breast pump further from sources of power frequency magnetic fields or to install magnetic shielding. The power frequency magnetic field should be measured in the intended installation location to assure that it is sufficiently low.
Conducted RF IEC 61000 -4-6

Radiated RF IEC 61000-4-3

| 3V 0,15 MHz – 80

MHz 6 Vin ISM and amateur radio bands between 0,15 MHz and 80MHz 80 % AM at 1 KHz

lOV/m 80 MHz -2,7 GHz 80% AM at

1 KHz

| 6V

lOV/m

| Portable and mobile RF communications equipment should be used no closer to any part of the breast pump, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.

Recommend separation distance d = 1.2 ÖP

d= 1.2 ÖP     80 MHz -800 MHz

d= 2.3ÖP     800 MHz- 2.7 GHz

 |  |  | Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m).
 |  |  | Field strengths from fixed RF transmitters ,as determined by an electromagnetic site survey, should be less than the compliance level in each frequency range. Interference may occur in the vicinity of equipment marked with the following symbol.
Note 1 At 80 MHz and 800 MHz, the higher frequency range applies.
Note 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast, cannot be predicted theoretically with accuracy. To assess the Electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the breast pump is used

exceeds the applicable RF compliance level above, the breast pump should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the breast pump. Over the frequency range 150 KHz to 80 MHz, field strengths should be less than 10 V/m.

Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the Breast Pump

This electric breast pump is intended for use in electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the electric breast pump can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the electric breast pump as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of transmitter W| Separation distance according to frequency of transmitter m
150kHz to 80MHz d= 1,2 Ö P| 80MHz to 800MHz d= 1,2 Ö P| 800MHz to 2,7 GHz d= 2,3 Ö P
0,01| 0,06| 0,04| 0,07
0,1| 0,18| 0,11| 0,22
1| 0,58| 0,35| 0,22
10| 1,84| 1,11| 2,21
100| 5,83| 3,50| 7,00
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1 at 80 MHz and 800 MHz the separation distance for the higher frequency range applies
Note 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.
WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the breast pump including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.

Using other cables and accessories that not provided from Lansinoh® may negatively affect EMC performance.

• FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Wireless Statement Wireless communications equipment such as wireless home network devices, mobile phones, cordless telephones and their base stations, walkie-talkies can affect this equipment and should be kept at least a distance of 3.5m away from the equipment.
• Stacking This device should not be used adjacent to or stacked with other equipment. And if adjacent or stacked use is necessary, this device should be observed to verify normal operation in the configuration in which it will be used.

Disposal

• The symbol which can be found on the product or on the package surface indicates that the product mustn’t be disposed with other household wastes.
• Waste equipment disposal by handing it over predetermined collection point for recycling is solely users’ responsibility. Seperate collection of the waste equipment and recycling them properly will preserve the natural resources, have a positive affect on the environment and will protect human health. For further information about the recycling collection points, please contact your local authority or place you purchased the product.
• Serious events experienced from using this product should be reported immediately to Lansinoh Laboratories and to the local competent Authority.
• This product is a personal care product and therefore cannot be returned once opened. If you experience any problems with this product, please telephone our free customer service line at 800-292-4794 or email customerservice@lansinoh.com.

This product is a personal care product and therefore cannot be returned once opened. If you experience any problems with this product, please telephone our toll free customer service line at 800-292-4794. Our representative will be happy to assist you.

Distributed by : Lansinoh Laboratories, Inc, Alexandria, VA 22314 USA, 800-292-4794 | Lansinoh.com

Lansinoh® is a registered trademark of Lansinoh Laboratories, Inc. / Lansinoh® es una marca registrada de Lansinoh Laboratories, Inc.

Manufacturer: Lansinoh® Laboratories Saglik Gerecleri Tasarim San. Tic. Ltd. Sti. Zafer SB Mah. Gunduz Sk. No:13 E.S.B Gaziemir/ Izmir/ Turkiye

FREQUENTLY ASKED QUESTIONS

What are the dimensions of the Lansinoh ‎53050 Double Electric Breast Pump?

The Lansinoh ‎53050 Double Electric Breast Pump measures 6 x 5 x 4 inches.

What is the material composition of the Lansinoh ‎53050 Double Electric Breast Pump?

The Lansinoh ‎53050 Double Electric Breast Pump is primarily made of plastic.

Does the Lansinoh ‎53050 Double Electric Breast Pump contain any harmful materials?

No, the Lansinoh ‎53050 Double Electric Breast Pump is free from BPA (Bisphenol A), a harmful chemical commonly found in plastics.

What type of pump does the Lansinoh ‎53050 Double Electric Breast Pump feature?

The Lansinoh ‎53050 Double Electric Breast Pump features an electric pump.

Can the Lansinoh ‎53050 Double Electric Breast Pump be operated using batteries?

Yes, the Lansinoh ‎53050 Double Electric Breast Pump can be powered by 6 AA batteries, providing optional portability.

How much does the Lansinoh ‎53050 Double Electric Breast Pump weigh?

The Lansinoh ‎53050 Double Electric Breast Pump weighs approximately 2 pounds.

What is the price of the Lansinoh ‎53050 Double Electric Breast Pump?

The price of the Lansinoh ‎53050 Double Electric Breast Pump is $84.99.

What warranty coverage is provided for the Lansinoh ‎53050 Double Electric Breast Pump?

The Lansinoh ‎53050 Double Electric Breast Pump comes with a one-year warranty on the pump mechanism (pump body and pump motor) and a 90-day warranty on all other product components.

Is the Lansinoh ‎53050 Double Electric Breast Pump suitable for daily use?

Yes, the Lansinoh ‎53050 Double Electric Breast Pump is designed for frequent and regular use, making it suitable for daily pumping sessions for nursing mothers.

Why is my Lansinoh ‎53050 Double Electric Breast Pump not turning on?

If your Lansinoh ‎53050 Double Electric Breast Pump is not turning on, first ensure that it is properly connected to a power source. Check the battery compartment if using batteries, and replace them if necessary. If using an electrical outlet, ensure it is functioning properly. If the issue persists, contact Lansinoh customer support.

How can I troubleshoot low suction power with my Lansinoh ‎53050 Double Electric Breast Pump?

Low suction power may be due to improper assembly or a clogged valve or tubing. Check all components for proper alignment and cleanliness. Ensure that the breast shields fit securely and that there are no leaks in the tubing.

What should I do if my Lansinoh ‎53050 Double Electric Breast Pump is producing uneven suction?

Uneven suction may occur due to improperly fitted breast shields or damaged valves. Ensure that the breast shields are centered and sealed correctly around the nipple. Replace any damaged valves or membranes.

How do I address excessive noise coming from my Lansinoh ‎53050 Double Electric Breast Pump?

Excessive noise could indicate a problem with the motor or a loose connection. Check all connections and ensure that the pump is placed on a stable surface.

What should I do if my Lansinoh ‎53050 Double Electric Breast Pump is leaking milk?

Leaking may occur if there are cracks or tears in the tubing, or if the valves and membranes are not properly assembled. Check all components for damage and ensure proper assembly. Replace any damaged parts.

How can I troubleshoot discomfort or pain while using my Lansinoh ‎53050 Double Electric Breast Pump?

Discomfort or pain may indicate that the breast shields are the wrong size or improperly positioned. Ensure that the breast shields fit comfortably and that the nipple is centered within the shield. Adjust the suction level if necessary.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK:Lansinoh ‎53050 Double Electric Breast Pump User Manual

REFERENCE:Lansinoh ‎53050 Double Electric Breast Pump User Manual- Device.Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>