Erlit ER3508P Shower cabin C3 80×80 frosted glass User Manual

ER3508P Shower cabin C3 80×80 frosted glass
User Manual ER3508/3509/3510/3512TP/TPF-RUS
ER3508/3509/3510/3512P/PF-RUS
ER4508/4509/4510/4512TP-RUS
ER4508/4509/4510/4512P-RUS

PRODUCER: ALEX BAITLER® GMBH Adolf-Kolping-Straße 16, 80336 München, Germany
COMPANY ACCEPTING CLAIMS FROM CUSTOMERS: ALEX BAITLER RUS LLC
141591, Moscow region, Solnechnogorskiy district, Sokolovo village, Industrialnaya street, building № 4, tel: 8-800-302-0209. Made in Russia

ER3508P Shower cabin C3 80×80 frosted glass

DEAR CUSTOMERS!
Thank you for choosing the products of ERLIT. trademark. This manual is designed for introduction to the product, as well as to the conditions for the proper installation,  operation, and maintenance of the product. Please read this manual carefully before installing and operating the product.
Thank you for the purchase!

GENERAL INFORMATION
The product is intended for domestic use indoors. The manufacturer reserves the right not to notify the final user of differences in the design of an outdated model and a new improved version of the product.
TECHNICAL CHARACTERISTICS

• The voltage applied was 220V ± 10%. Internal voltage 12V;

• The thickness of the safe tempered glass is 4mm (EU directive EN 14428);

• Water pressure applied 0.2-0,4 МPа, water consumption 8-12 l/min. The temperature of hot water supply should be no
  more than 70°С;

• Installation of coarse filters 100 μm for water is required;

• Connecting dimensions of hot and cold pipeline 1/2” (15 mm), tap hole diameter 1 ½” (40 mm);

• The sewer inlet level should be no less than 70 mm lower than the shower tray drain level;

• The maximum load on the tray is 370 kg.

IT IS PROHIBITED TO DO THE FOLLOWING

• Use the product for purposes other than intended;
• Use the product outdoors;
• Expose the product to direct sunlight;
• Be inside under alcohol or drug influence;
• Subject the product to mechanical damage of any kind;
• Apply excessive force to the components during installation and operation processes
• Use the product unattended for people with disabilities;
• Use abrasive and/or chemically aggressive cleaners.

TRANSPORTATION AND STORAGE

• The products must be transported in a covered vehicle.
• At the time of installation, the product must be of a room temperature
• The product has to be stored in the original packaging aſt er the purchase in order to be accepted for an aſt er sales service.

RECOMMENDATIONS TO BUYERS

• To check the completeness and the entirety of the product at the moment of receiving;
• Before the assembly all repair and decorative works should be completed;
• Cleaning of the shower cabin should be performed with a soſt piece of cloth using liquid washing agents without abrasive and/ or chemically aggressive components;
• Do not put glasses on fl oor without protective cardboard, avoid impacts and putting glasses on the corner;
• To seek an authorized service center or other specialists having appropriate qualifi cation for installation and maintenance of the product..

COMMUNICATIONS PREPARATION LAYOUT

RECOMMENDED CABIN INSTALLATION TOOLS

Box №1 (front glass)

Box with fittings (located in box №2)

|
---|---

Box with fi ttings (located in box №2)

|
---|---

THE SCHEME IS SYMMETRICAL CABINS ER 35/45 SERIES
Schematic diagram of the basin assembly size: 80×80; 90×90; 100×100

THE SCHEME IS SYMMETRICAL CABINS ER 35/45 SERIES

ATTENTION! The steps listed below show the basic installation of the product. The order of the steps may differ depending on the utility systems and the size of the premises. Step 1 to perform when you buy tray disassembled form.

Place the shower cabin tray into the installation place; using a level tube place it in a strictly horizontal manner and make sure that all legs are reliably fastened to the tray foundation.  Insert a discharge hose into the discharge hole and treat it with silicone glue.
Assembly of shower cabin body size: 80х80; 90х90; 100х100

Assembly of shower cabin body size: 120х80

Back glass mounting of the next cabin: ER3508/09/10; ER4508/09/10

Back glass mounting of the next cabin: ER3512 / ER4512

WATER SYSTEM DIAGRAM

Connect metal pipes in the wall with cold and hot water pipes, then fasten them. Make sure that there are no leaks.
Insert a discharge hose into the discharge hole and treat it with silicone glue. And now, aſter finishing installation wait for 3 hours, aſt er which connects the electric power and water. Place the cabin in the place of final installation in your bathroom.

MANUAL FOR REMOTE CONTROL USAGE

ELECTRICAL SCHEMATIC

Thank you for choosing ERLIT products!
These warranty obligations complement the rights and obligations of consumers, as defi ned by law, without limiting them in any way. For all questions related to the installation,  operation, and maintenance of the product, please contact the authorized service centers or a toll-free telephone service support line. The useful life of the purchased product is 10 years.
The manufacturer’s warranty for the product and its components is 1 year. The manufacturer’s warranty on the tray is 5 years. When mounting the product employees of authorized service centers warranty on the cabin 2 years, on a pallet 7 years. The manufacturer’s warranty and Service guarantee are valid from the date of sale.
When a customer contacts a trading organization or an authorized service center, the consumer must present a cash or sales receipt, or other evidence of concluding a contract and paying for the goods. To carry out warranty service, the buyer must provide free access to the product.
Appearance and completeness of the product must be checked by the buyer at the time of receipt of the disassembled product. Further claims for appearance and completeness are not accepted.
WARRANTY DOES NOT COVER:

• Products used in public places;
• Defects caused by improper installation and/or violation of the operating rules;
• Faults caused by the poor quality of tap water and pipe corrosion;
• Faults caused by voltage fluctuations in the electrical network;
• Damage caused by natural disasters;
• Damage caused by the use of care products not intended for this product.
  Your suggestions for improving the quality of service you can send to: service@sanplan.ru
  TOLL-FREE TELEPHONE HOTLINE FOR SERVICE SUPPORT 8-800-707-0899

WARRANTY COUPON

Model———————-
Seller———————-
Date of sale « ——————– » 20 ——————–
I have read and understood warranty obligations
I have checked the completeness of delivery as to the shower cabin
The product does not have visible mechanical defects
Buyer ——————-

www.erlit.ru

References

• ERLIT - Душевые кабины ERLIT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>