ASOPARTS 2 EBike Rack with Ramp Installation Guide

ASOPARTS 2 EBike Rack with Ramp

Product Information

Specifications:

• Hitch size: 2”
• Maximum load capacity: 2 e-bike up to 200 lbs capacity
• Tire width: up to 3.35” (8.5cm)
• Wheelbase: up to 53.15” (135cm)

Installation:

1. Assemble the tongue to the rack
   Align holes on the tongue to those on the rack. Install bolts, washers, and nuts, and tighten them with wrenches. Install the clevis pin & R clip on the tongue.

2. Install the tongue into your hitch receiver
   Insert the tongue into the hitch receiver. The hole on the tongue must align with that on the hitch receiver. Install the hitch bolt & nut.

3. Center the trays
   Loosen the underside nuts and center the trays. Then tighten the underside nuts.

Loading:

1. Prepare for loading
   Loosen the ramp knobs and pull out the whole ramps. Unbuckle the strap that secures the mast. Pull the security pin & clip and raise the mast. Then insert the security pin & clip in place. Slightly loosen the stabilizer knobs and rotate them out of the way. Unbuckle the straps.

2. Rolling E-Bikes onto Trays:

   • Roll your e-bikes up the ramps and onto the trays.
   • E-bikes can be loaded in the same or opposite directions.
   • Do not use electric power to load your e-bikes.
   • Carry the heavier e-bike on the inside tray.
   • Always center e-bikes on the trays.

3. Adjusting Stabilizers:

   • Loosen the stabilizer knobs and adjust the height of stabilizers.
   • Rotate the stabilizers toward the e-bikes and adjust their positions so that they engage with the frames or seat posts of the e-bikes.
   • Clamp the frames or seat posts. Once positioned, tighten the stabilizer knobs.

FAQ:

• Q: Can I use electric power to load my e-bike onto the rack?
  A: No, do not use electric power to load your e-bike as it is not recommended and may cause damage to the rack or e-bike.

• Q: How should I secure my e-bikes on the rack?
  A: Make sure to tighten all straps, stabilizer knobs, and check for any loose hardware before each use. Always center your e-bikes on the trays for proper balance and stability during transportation.

SAFETY WARNING

• The rack and its parts must not be modified in any way.
• Remove this rack before entering an automatic car wash, and when not in use.
• Ground clearance of 10” or higher is recommended.
• Drive slowly over speed bumps, 5-10 mph (8-16 kph) max.
• The vehicle’s total length or height may increase when a rack is mounted. The e-bikes themselves may increase the vehicle’s total width or height. Take special care when reversing or entering garages.
• Be aware that the vehicle’s driving characteristics and braking behavior might change and that the vehicle might become vulnerable to side winds when the rack is fitted. Do not position e-bike tires directly in back of your vehicle’s hot exhaust.
• Not for use with tandems or recumbents.
• Do not transport e-bikes with attached baby seats, panniers, wheel covers, or full bike covers.
• Be sure all hardware is secured according to these instructions.
• Verify that e-bikes are secured to the rack before operating your vehicle.
• Read your e-bike owners manual about safe keeping of the battery. Follow all guidelines and consider removing the battery if concerned about theft, damage or performance loss from prolonged heat/cold.
• The vehicle’s tail lights can be obstructed. If that is the case, an external light board must be fitted.
• An additional number plate might be required. This should be attached to the appropriate part of the rack in accordance with local laws.
• Be aware that wind noise may be generated during transport and may vary depending on the vehicle and load.

PACKAGE CONTENTS

PARAMETER

• Hitch size: 2”
• Maximum load capacity: 2 e-bike up to 200 lbs capacity
• Tire width: up to 3.35” (8.5cm)
• Wheelbase: up to 53.15” (135cm)

INSTALLATION

1. Assemble the tongue to the rack

   • Align holes on the tongue to those on the rack.
   • Install bolts, washers and nuts, and tighten them with wrenches.(1a)
   • Install the clevis pin & R clip on the tongue.(1b)

2. Install the tongue into your hitch receiver
   Insert the tongue into the hitch receiver.(2a)

   • The hole on the tongue must align with that on the hitch receiver.
   • Install the hitch bolt & nut.(2b)
   • Warning: Attachment hardware can loosen over time. Check before each use, and tighten if necessary.
   • Note: This product is not designed for vehicles with a rear mounted spare tire. For vehicles with a rear mounted spare tire, a hitch extension is required.

3. Center the trays

   • Loosen the underside nuts and center the trays. Then tighten the underside nuts.

LOADING

1. Prepare for loading

   • Loosen the ramp knobs and pull out the whole ramps.(1a)
   • Unbuckle the strap that secures the mast.(1b)
   • Pull the security pin & clip and raise the mast. Then insert the security pin & clip in place.(1c)
   • Slightly loosen the stabilizer knobs and rotate them out of the way. Unbuckle the straps.(1d)
   • Note:
     You can roll your e bikes onto the trays from either the left or the right by unscrewing the screws under the trays,then lifting and reversing the whole trays.

2. Roll your e-bikes into place

   • Roll your e-bikes upthe ramps and onto the trays.
   • Note: E-bikes can be loaded in the same or opposite directions.
   • Caution: Do not use electric power to load your e-bikes.
   • Recommendation: Carrythe heavier e-bike on the inside tray.Always center e-bikes on the trays.

3. Securethe e-bikeswith the stabilizers

   • Loosen the stabilizer knobs and adjust the height of stabilizers.(3a)
   • Rotate the stabilizers toward the e-bikes and adjust their positions so that they engage with the frames or seat posts of the e-bikes.(3b)
   • Clamp the frames or seat posts. Once positioned, tighten the stabilizer knobs.(3c)
   • Caution: Loose stabilizer knobs may cause damage to e-bikes, vehicle and persons.

4. Securethewheelstraps

   • Loosenthe strap knobs and adjust the straps so that they are located below the axles. (4a)
   • Threadthe straps around the tires and through the buckles, and pull upthe gray release tabs to tighten. (4b)
   • If you load 2 e-bikes,you can offset the trays as needed to clear saddles and handlebars.(4c)

Storethe ramps(seeFigure 1.)
Whenthe ramps are not in use, pushthem into the trays and tighten the ramp knobs.

Unloading

• Loosenthe ramp knobs and pull out the ramps.
• Pressthe gray release tabs on the buckles and release the straps.
• Loosen the stabilizer knobs to release the clamps.
• Roll your e-bikes onto the ground.
• Pushthe ramps into the trays and tighten the ramp knobs.

Tilt (see Figure 2.)

• Remove the clevis pin & R clip and install them into the lower hole.(a)
• Remove the security pin & clip while supporting the load.(b)
• Slowly and carefully lower the rack.(c)

Caution!
Thetilt feature requires 2 PEOPLEto operate.One person MUST support the loadwhile the other removes the security pin & clip. Do not put any part of your body under the rack while tilting. Be careful to avoid hitting your head.

Storage

Storage (see Figure 3.)
Unload your e-bikes by following Unloading steps.

• Removethe security pin & clip of the mast and fold downthe mast.
• Then insert the security pin & clip in place.
• Bucklethe strap to secure the mast.
• Remove the clevis pin & R clip.
• Fold up the e-bike rack.
• Install the clevis pin & R clip into the higher hole.

Removal

• Unloadyour e-bikes.
• Remove the hitch bolt & nut.
• Removethe rack from yourvehicle.
• Store the rack in a safe place.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>