InstantVap 18V Battery Powered Oxalic Acid Vaporizer Instructions

InstantVap 18V Battery Powered Oxalic Acid Vaporizer

Specifications

• Product Name: InstantVap 18V Original
• Type : Battery-powered oxalic acid vaporizer
• Battery Voltage: 18-20V
• Battery Capacity: Minimum 4Ah

Product Usage Instructions

Safety Information

Ensure to wear proper safety gear including thick gloves, long sleeves, respirator, and safety glasses. The unit retains heat after use, so avoid remaining it on flammable materials.

Before You Start

1. Use the correct type of battery with a voltage of 18-20V and at least 4Ah capacity.
2. Ensure the battery is fully charged.
3. Use oxalic acid dihydrate of 97%-100% purity without additives like glucose and silica.

Operation

1. Remove the dispenser (C) from the device and set it to the desired dosage (1 to 4 grams) by turning the handle (16).
2. Check the indicator (15) to match the grams of oxalic acid dispensed.
3. Do not exceed the indicator limit and place the dispenser back in the device.
4. Connect your battery to the battery socket (7) to power up the unit.
5. The voltage display (D) and controller display (11) will show the battery voltage, set temperature, and actual temperature.
6. The unit will turn off automatically when the battery voltage drops below 15V and will not turn on with a battery below 17.2V.

FAQ

• Q: Can the InstantVap 18V Original be used in wet conditions?
• A : No, the device is not to be used in rain or wet conditions for safety reasons.
• Q: What happens if I use a battery with a lower capacity than recommended?
• A: Using a battery with less than 4Ah capacity may result in shorter operating times and could potentially damage the device.
• Q: How often should I clean the InstantVap 18V Original?
• A : It is recommended to clean the unit after each use to maintain its efficiency and prolong its lifespan.

Illustrations

Congratulations on your new InstantVap oxalic acid vaporizer. This manual contains important information, please take the time to read this manual thoroughly.

The InstantVap 18V Original unit is to be used for oxalic acid vaporization treatments against Varroa mites in apiaires. This manual does not contain information about oxalic acid treatments in general. Please educate yourself on oxalic acid vaporization before using this device. Your InstantVap 18V Original package includes:

• 1 piece of InstantVap 18V unit with the chosen battery socket (A)
• 1 piece of dispenser (C)
• 1 piece of silicone cleaning cap (F)
• 2 pieces of spare O-rings (G)

Optional accessories available for purchase:

• silicone insulation cover (E)
• silicone insulation tapered (H) – to be cut at the dotted line
• silicone insulation tube (I)

Safety Information

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to be cautious and care when installing, maintaining, or operating your InstantVap device. This appliance is not to be used by children of any age and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

Safety Symbols

• WARNING HOT SURFACE
• WARNING SHARP EDGES

Safety Gear

• Proper safety gear must be worn during installing, operating and maintaining this device!
• Proper safety gear includes thick gloves, long sleeves, respirator (full face mask with ABE1P3 or ABE2P3 combined filter inserts), and safety glasses.
• For outdoor use only!
• The unit retains heat for long after use! Risk of burns!
• Do not rest the device on flammable materials. Risk of fire!
• Transport only when cooled and battery removed.

Before you start

Make sure you use the correct type of battery, and your battery is fully charged. The InstantVap 18V Original model is to be used with batteries of 18-20V. It is recommended to use batteries with at least 4Ah capacity. Get the oxalic acid ready. The InstantVap units are to be used with oxalic acid dihydrate of 97%-100% purity. Be aware that some oxalic acid products contain additives like glucose and silica, which are unsuitable for use in this device. Put on your safety gear. Keep your safety gear on at all times, even during cleaning and maintainance. The InstantVap devices are not to be used in rain.

Operation

Remove dispenser (C) from the device. Set your dispenser at the desired dosage. The dispenser can be adjusted by turning the handle (16) while checking the indicator (15). The numbers on the indicator correspond to the grams of oxalic acid the dispenser holds. It can be set from 1 to 4 grams. Do not twist past the indicator. Place the dispenser back in the device.
Connect your battery to the battery socket (7). The voltage display (D) and the controller display (11) light up. The voltage display shows the voltage of the battery. The controller display shows the set temperature (9) and the actual temperature (10).
Note: the device is set at the recommended temperature of 230ºC (445ºF) as default. Units sold in the US are set in Fahrenheit, all other units are set in Celsius degrees. The set temperature can be changed by pushing the buttons: arrow down (13) and arrow up (14). Turn on the switch (12). The unit starts heating up. Wait until the unit heats up to the set temperature. Place the vaporizer in place for treatment. Remove dispenser from the device and press dispenser into oxalic acid to collect the dose, then place it into the device and depress it. Allow the treatment to be completed. The treatment is completed when the unit re-heats to a few degrees below the set temperature. At this point, you can place the unit ready for the next treatment, re-load the dispenser, and apply the next dose. Keep repeating until all your treatments are completed or your battery is discharged. The unit turns off automatically when your battery is discharged (below 15V) and does not turn on while a discharged battery is connected (below 17,2V).
After finishing treatments, turn off the switch, remove battery from the socket and charge the battery. Clean the unit and allow it to cool down.

Maintenance

Clean the unit at least after every 100 treatments. Put on your safety gear, including your gloves, mask and safety glasses. Make sure the unit is not clogged. Heat up the unit to 200ºC (390ºF) in case it is cooled. Turn the unit off and remove the battery. Remove dispenser (C) from the unit. Fill the silicone cleaning cap (F) with water to one-third full. Turn the heated unit upside down and push the cap on the dispenser’s tube (4). Keep pushing the cleaning cap very hard, point the outlet tube (1) away from you and turn the unit back. Repeat it until the unit does not generate any more steam . WARNING! High pressure and hot steam! Rinse the cooled unit by adding a full cap of water through the dispenser’s tube (4), shaking it and draining it through the dispenser’s tube (4). Repeat until the drained water is clear. Clean the outside of the unit by wiping it with a damp cloth. The dispenser is to be washed in water. Add a drop of mineral oil or grease to the O-ring (G) to increase lifespan and ease of use.

Optional accessories

he silicone insulation cover (E) is to protect the unit from falling oxalic acid. Remove dispenser from unit. Position the silicone cover with the curved side (17) in the front. Push the silicone cover on the top of the unit (3) through the dispenser’s tube (4). Make sure to push it all the way down and not to leave any gap between the cover and the top of the unit. The tapered silicone insulation (H) is to protect heat-sensitive materials from the hot outlet tube (1). Cut it off at the dotted line and push it onto the outlet tube.
The silicone insulation tube (I) is to protect heat-sensitive materials from the hot outlet tube (1). Push it onto the outlet tube.

Tips

• The handle (6) of the unit can hold a spare dispenser (C).
• The gripping edges (8) hold the device in place during treatment, no need to hold onto it.
• Do not waste time once the unit is heated. Treat in a timely manner to fully utilize battery capacity. No need to wait until the unit reaches the set temperature between treatments, you can start your next treatment while the unit is getting a few degrees close to the set temperature.

Troubleshooting

• The voltage display (D) and controller display (11) do not light up after connecting the battery:
  • check your battery charge level.
• The displays turn on, but the unit does not heat:
  • turn on the switch (12).
• The unit shows FT803 repeatedly after switching on:
  • the battery is faulty, old or has too low capacity (1-3Ah).
• The unit heats up very slowly:
  • water residue may be in the heating chamber (2). Let it boil off.
• The unit is unable to heat over around 110 ºC (230ºF):
  • the insulation around the heating chamber (2) may have got wet. Contact manufacturer/dealer for instructions.
• The start of the treatment is long delayed after applying oxalic acid:
  • the heating chamber (2) may be covered with charred residues. Contact manufacturer/dealer for instructions.
• The dispenser (C) pops out after dosing:
  • the outlet tube (1) is clogged.
• The outlet tube (1) is clogged:
  • warm the outlet tube with a blowtorch or drill into the outlet tube with a max. 3mm(1/8inch) drill.
• The outlet tube (1) keeps clogging:
  • the outlet tube is in contact with wet materials that keep cooling it down.
• The dispenser (C) fits very tight:
  • add a drop of mineral oil or grease to the O-ring (G).
• The dispenser (C) fits too loosely:
  • change O-ring (G).

Warranty

A 2-year manufacturer warranty is provided for the InstantVap units (accessories are not included). In case of any failure: in Europe: go to www.instantvap.eu/service and follow the steps described there. UK and outside of Europe: please contact your dealer.

Technical data

• InstantVap 18V Original oxalic acid vaporizer
• Power: 18V-20V DC; 250W; 14A
• Operating temperature: 200-260ºC (400-465ºF)
• Default temperature: 230ºC (445ºF)
• Weight without battery : 1,55 kg (3,4lbs)
• Equipped with over-discharge battery protection
• Manufacturer : InstantVap Tech Kft. (CRN: 01-09-411646, Tax nr.: HU27783210) Made in Hungary

For other languages, please go to www.instantvap.eu/instructions

References

• InstantVap Service Centre - InstantVap Battery Powered Cordl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>