Sentry H2O CP-SWS Sentry Wellness System Instructions

June 2, 2024
Sentry H2O

Sentry H2O CP-SWS Sentry Wellness System

Sentry Wellness System Contents (P/N: CP-SWS)

  • 1 Pre-Installed White Bracket
  • 2 Clear Housings with O-Rings
  • (Labels indicate the corresponding filter)
  • 1 Catalytic Carbon Filter
  • 1 Trappsorb Drop-In Filter
  • 1 In-Line Pressure Relief Valve (PRV)
  • 1 1/4” Tubing for Cold Water-to-Inlet
  • Connection (with PRV installed in-line)
  • 1 1/4” Tubing for Outlet-to-Faucet
  • Connection (with male brass fitting)
  • 1 Wrench
  • 2 Screws (for mounting to wall)
  • Verify you have the necessary components listed above before starting installation.

Tools Needed (Not Included)

  • 1-2 Adjustable Wrenches/Pliers
  • Drill with a Philips Head Drill Tip
  • Scan to watch the installation video or visit SentryH2O.com

Instructions

IMPORTANT
DO NOT REMOVE PLASTIC WRAP FROM FILTERS UNTIL STEP 2.

STEP 1
Choose a location for installation (i.e. cabinet wall next to your fridge) and mount the system bracket using the provided screws. We recommend using a sharpie or pen to mark the mount points, then drill the screws, and then place the system bracket on the screws.

STEP 2
Remove plastic wrap from filters and place the filters into their corresponding housings. The Catalytic Carbon Filter MUST be placed into the Catalytic Carbon Housing on the left side of the system and the Trappsorb Drop-In Filter MUST be placed into the Trappsorb Housing on the right side of the system. Unwrap and place each filter one at a time to avoid mixing them up. Tighten the housings closed by hand and then use the provided wrench to snugly fit the bowls to the lid, typically an ⅛-¼ turn, until the labels are facing forward.

STEP 3
Identify the water source for your fridge and turn the water valve counter- clockwise (OFF) to the off position. This valve should remain off for the entire installation process.

STEP 4
Using an adjustable wrench, remove the fridge line from the water valve. Position a container beneath the valve to catch water from the line.

STEP 5
Locate the provided cold water-to-inlet connection tubing with the PRV valve installed and the female crush collet. With the PRV arrow facing towards the system, push the tube into the cold water valve. Tighten the collet to the valve by hand and then use the adjustable wrench to fully tighten. Tug on the line to ensure a tight fit.

STEP 6
Using the provided outlet-to-faucet tubing with the male brass fitting, thread the brass fitting onto the fridge line (this is the line that was removed from the cold water valve in Step 4). Tighten by hand and then use 1 or 2 wrenches to fully tighten. Tug on the line to ensure a tight fit.

STEP 7
Using the cold water valve tubing from Step 5, push the tube end into the Inlet Head (Catalytic Carbon Housing lid) until the tube bottoms out or can no longer be pushed in. Tug on the tube to set the connection. Then push the outlet-to-faucet tubing from Step 6 into the Outlet Head (Trappsorb Housing lid) until the tube bottoms out. Tug to ensure tight fit.

STEP 8
Restore the water flow by turning the water valve clockwise (On) with your faucet on. Check for leaks at the fitting locations or bowl gasket locations. If there is a leak, either the tubes need to be pushed in further or the housings need to be Re-Seated. We recommend checking at this point and then again once you turn off your faucet.

STEP 9
Keep the cold water running for 5-10 minutes to purge the system of excess carbon dust and trapp sorb dust. If the water appears cloudy and doesn’t taste sweet, continue to purge the system for another 5 minutes. As the system normalizes, you may notice reduced water pressure for up to one week.

STEP 10
Replace both filters annually and enjoy your new Wellness System!

Questions or concerns?
Email us 24/7 at CleanWater@SentryH2O.com or give us a call at 1-833-377-3817 Mon-Fri from 8 am-4 pm AZ Time.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals