BOSCH GNB 18V-38 Professional Cordless Concrete Nailer User Manual

BOSCH GNB 18V-38 Professional Cordless Concrete Nailer User Manual

Safety Instructions

General Power Tool Safety Warnings
⚠ WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock..
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

•  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
  Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
  Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
  Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
  Nailer safety warnings

• Always assume that the tool contains nails. Careless handling of the nailer may result in unexpected firing of nails and personal injury.

• Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the nails causing an injury.

• Do not actuate the tool unless the tool is placed firmly against the workpiece. If the tool is not in contact with the workpiece, the nail may be deflected away from your target.

• Disconnect the tool from the power source when the nail jams in the tool. While removing a jammed nail, the nailer may be accidentally activated if it is plugged in.

• Use caution while removing a jammed nail. The mechanism may be under compression and the nail may be forcefully discharged while attempting to free a jammed condition.

• Do not use this nailer for fastening electrical cables. It is not designed for electric cable installation and may damage the insulation of electric cables thereby causing electric shock or fire hazards.

• Disconnect the nailer from the power source when loading and unloading nails, making adjustments or changing accessories. The nailer may be accidentally activated if it is connected to the power source, which may result in personal injury.

• Be careful when handling nails, especially when loading and unloading. The nails have sharp points which may result in personal injury.

• Keep fingers away from trigger when not operating this nailer and when moving from one operating position to another. Unexpected triggering will discharge a nail, which may result in personal injury.

• Hold the nailer by insulated gripping surfaces, when performing an operation where the nail may contact hidden wiring. A nail contacting a “live” wire may make exposed metal parts of the nailer “live” and could give the operator an electric shock.

• Hold the nailer with a firm grasp during operation. Uncontrolled recoil of the nailer may result in unintended activation, which may result in personal injury.

• Keep all body parts such as hands and legs, etc. away from the firing direction of the tool. The nail may penetrate the workpiece as well as any object behind it, which may result in personal injury.

• When using the nailer, keep all body parts such as hands and legs, etc. away from the area where the nails is driven into the workpiece. The nail could deflect and exit the workpiece, which may result in personal injury.

• Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage.

• In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

• Do not open the battery. There is a risk of short-circuiting. u The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.

• Only use the battery in the manufacturer’s products. This is the only way in which you can protect the battery against dangerous overload.

Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short- circuiting.

• Do not use the power tool and the nails on very soft materials (e.g. wood, lightweight construction materials). The nails may penetrate the substrate and may cause injury.
• Do not use the power tool and the nails on very hard materials (e.g. high-strength steel, very hard natural stone) or on types of concrete with high compressive strength or aggregate with high compressive strength. If the material is too hard, the nail may ricochet, break and escape and may hit you or other persons and may cause injuries.
• Never hold the power tool when it is at an acute angle to the substrate. The power tool must be perpendicular to the substrate. There must be no contamination on the substrate.
• Do not deactivate or remove the contact element. The contact element is a safety mechanism to reduce the risk of unintentional triggering. Deactivating this component may lead to unintentional triggering.
• Only use the power tool if the contact element is functioning correctly. If the contact element is defective, the power tool may trigger unexpectedly.
• Always fill the magazine of the power tool with nails first before you insert the battery. This reduces the risk of accidentally discharging a nail and injuring yourself or other people.
• Never discharge nails in the vicinity of flammable materials. When driving in some nail types, sparks may fly out of the contact element.
• Never discharge a nail on top of another nail. This may lead to the nail being deflected or the power tool reacting unexpectedly.

Product Description and Specifications

Read all the safety and general instructions. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury. Please observe the illustrations at the beginning of this operating manual.

Intended Use
The power tool is designed to put nails into hard materials such as concrete (e.g. poured concrete, grouted joints) and steel (e.g. structural steel, hot- rolled steel). The power tool must not be used on very soft surfaces (e.g. wood, lightweight construction materials) or very hard surfaces (e.g. high- strength steel). The power tool must also not be used on the following substrates: Natural stone, vertical mortar joints, hollow blocks, bricks, glazed brick, glass, hardened steel, tool steel, spring steel, cast iron, weld seams. Check the suitability of the substrate before use (see “Checking the Suitability of the Substrate”, page 20). The power tool is intended for hand- held use only. The power tool is only intended for indoor use.

Product Features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

1. On/off button (user interface)
2. Power tool status indicator (user interface)
3. Battery charge indicator (user interface)
4. Reset button (user interface)
5. Unlocking switch for trigger (
6. Trigger
7. Handle (insulated gripping surface)
8. User Interface
9. Rechargeable battery release button)
10. Rechargeable battery)
11. Magazine release lever
12. Magazine
13. Supporting leg
14. Magazine slider
15. Magazine slider button
16. Contact element release button
17. Contact element
18. Outlet
19. Worklight
20. Depth stop switch
21. Punch pin (22) Nail stripa)
22. Utility hook
    a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical Data

Noise/Vibration Information
Noise emission values determined according to EN 60745216. Typically, the A-weighted noise level of the power tool is: Sound pressure level 85 dB(A); sound power level 96 dB(A). Uncertainty K = 3 dB. Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 60745216: ah = 5.7 m/s2, K = 1.5 m/s2.
The vibration level and noise emission value given in these instructions have been measured in accordance with a standardised measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.
The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This may significantly reduce vibration and noise emissions over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organising workflows correctly.

Rechargeable battery

Bosch sells some cordless power tools without a rechargeable battery. You can tell whether a rechargeable battery is included with the power tool by looking at the packaging.
Charging the battery
u Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.
Note: Lithium-ion rechargeable batteries are supplied partially charged according to international transport regulations. To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.

Inserting the Battery
Push the charged battery into the battery holder until it clicks into place.

Removing the Battery
To remove the rechargeable battery, press the battery release button and pull the battery out. Do not use force to do this. The rechargeable battery has two locking levels to prevent the battery from falling out if the battery release button is pressed unintentionally. The rechargeable battery is held in place by a spring when fitted in the power tool.

Battery charge indicator
The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge when the power tool is not in operation.
Press the button for the battery charge indicator or to show the state of charge. This is also possible when the battery is removed.
If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.
The state of charge of the battery is also displayed on the user interface (see “Status indicators”, page 22).

Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of -20 to 50 °C. Do not leave the battery in your car in the summer, for example.
Occasionally clean the ventilation slots on the battery using a soft brush that is clean and dry.
A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Assembly

Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
Inserting/Changing the Magazine (see figure A)
Insert the magazine (12) into the power tool and allow it to engage. To change the magazine, press the unlocking lever (11) clockwise. Remove the magazine from the power tool with a slight rotation.

Filling/Emptying the Magazine (see figure B)

• Be careful when handling nails, especially when loading and unloading. The nails have sharp points which may result in personal injury.
• Only use nails that have been recommended by Bosch for your power tool. Using unapproved nails can damage the power tool and cause injuries.
  During any work on the magazine, hold the power tool in such a manner that the outlet (18) is not pointed at your body or at other persons.

Select nails suited to the intended application:

– If necessary, clean the magazine slider (14) and magazine (12), e.g. with a paintbrush.
– Press the button (15) on the magazine slider (14) and slide it towards the magazine opening until it engages.
– Push a suitable nail strip (22) into the magazine opening.
The standard magazine can be filled with maximum 2 nail strips and the extended magazine (accessory) can be filled with 4.
– Press the button (15) on the magazine slider (14) and slide it forwards as far as it will go.
Note: If only 2 nails are contained in the magazine (12), the contact element (17) can no longer be pressed and no discharging procedure is triggered. Fill up the magazine.
Emptying the Magazine:
– Press the button (15) on the magazine slider (14) and slide it towards the magazine opening until it engages.
– Rotate the magazine so that the nail strip (22) can slide out of the magazine opening

Removing/Changing the Contact Element (see figure C)
The contact element (17) can be removed to be cleaned or changed. Remove the rechargeable battery (10). Empty the magazine (12) and remove it.

Pull the contact element release button (16) and remove the contact element (17) from the power tool. Push the cleaned or new contact element (17) into the power tool until it engages.

Operation

Starting Operation
Switching On and Off To switch on the power tool, press the on/off button (1) on the user interface until the user interface lights up. To switch off the power tool, press the on/off button (1) again. The power tool switches off automatically after 30 min if it is not being used.
Checking the Suitability of the Substrate Check the suitability of the substrate before loading the power tool with nails or performing fastening. The substrate must be level and free from residue. To check the hardness of the substrate material, use a nail as a centre punch. Use a hammer to hit it with a powerful strike on the material. Check the result:
– The point of the nail is blunted: The substrate is too hard and not suitable; the nail may ricochet.
– The material tears or splinters: The substrate is too brittle and is not suitable. Particles may hit you or other people, or the nail may completely penetrate the substrate.
– When struck with a hammer, the nail sinks into the substrate: The substrate is too soft and is not suitable; the nail may fully penetrate the substrate.
– The nail leaves behind a small recess in the substrate: The substrate is suitable for fastening.
Initiating the Discharging Procedure
– Switch on the power tool.
– Press the unlocking switch (5) to the left to unlock the trigger (6) (see figure D).
– Ensure that you hold the power tool by the handle (7) with a firm grip.
– Press the contact element (17) all the way to the substrate.
When the contact element is pressed, the worklight (19) lights up and illuminates the work area in poor lighting conditions.
– Afterwards, briefly press the trigger (6) and release it again. This discharges a nail into the substrate.
– Note: The trigger (6) must be pressed within 2 s after pressing the contact element (17). Otherwise, the power tool goes into safe mode and the discharging process must be restarted.
– For another driving procedure, lift the power tool fully off the substrate and position it firmly at the next required location.
– During work breaks and when work is finished, secure the trigger (6) by pressing the unlocking switch (5) to the right (see figure D).
Note: Securing prevents triggering if the contact element (17) is not fully pressed or the trigger (6) has not been released between discharging procedures.

Working Advice
u Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
Before starting work, always check that the safety and actuation devices are functioning correctly and that all screws and nuts are tightly seated. If a power tool is defective or not functioning properly, disconnect it immediately from the power supply and contact an authorised Bosch after-sales service centre.
Do not perform any incorrect manipulations on the power tool. Do not disassemble or block any components of the power tool. Do not carry out “emergency repairs” with unsuitable means.
Avoid any tampering and damage to the power tool, e. g. from: ­ Imprinting or engraving,
­ Retrofitting measures not approved by the manufacturer,

English | 21 ­ Dropping on or sliding over the floor, ­ Using as a hammer, ­ Applying any kind of force. For longer work breaks and after finishing work, switch off the power tool, remove the battery and empty the magazine if possible.

Requirements for Discharging Procedures
When fastening, observe the manufacturer’s specifications for the material being fastened, as well as the construction plans for the systems. Make sure to check whatever is below or behind your workpiece. Do not insert nails into walls, ceilings or floors when persons are behind them. The nails may punch through the substrate and may cause injury.

Check whether the nails have been inserted correctly. For fastening to be secure, they must sit neither too high nor too low nor be bent. If concrete is damaged by failed nails, it must be repaired in accordance with recognised rules.

Please find the following information in the documentation of Bosch nails at http://www.bosch-pt.com:
– Nail head distance hNHS
– Effective embedment length hef
– Minimum thickness of concrete element h
– Minimum distance between two nails smin
– Minimum edge distance cmin
– Recommended loads

Adjusting the Depth Stop Set the fastening depth using the depth stop switch (20) so that the correct value for the nail head distance hNHS is achieved.
Nail too deep: Press the depth stop switch (20) to the right. If the nails are driven in too deep, use longer nails. Nail not deep enough: Press the depth stop switch (20) to the left. If the nails are not driven in deep enough, use shorter nails.
Clearing Jams/Resetting Clear jams if the status display (2) lights up red or orange, or if the nails are no longer discharged correctly. ­ Remove the rechargeable battery (10). Empty the magazine (12) and remove it. Remove the contact element (17). ­ Check the magazine (12) and clear away dirt, residue and foreign objects. ­ Check the contact element (17) and clear away nails, nail fragments, residue or foreign objects with the punch pin (21). When doing so, ensure that you do not damage the contact element.
Status indicators

­ In sequence, re-insert the contact element (17), magazine (12) and battery (10).
­ Switch on the power tool. ­ Press the reset button (4) for 5 seconds. ­ Press the contact element (17) against a wooden block or similar and press the trigger (6). By doing this, the motor can bring the firing pin into the correct position. ­ If another fault is detected, the power tool does not return to normal operation. Instead, the other fault appears in the status display (2).
Removing the Supporting Leg The supporting leg (13) allows the power tool to be aligned at a perpendicular angle on an even substrate. For work on an uneven substrate, you can remove the supporting leg (13). To do so, slide it behind the magazine (12).
Hanging Up the Power Tool You can use the utility hook (23) to attach the switched-off power tool to a suitable suspension device. Using the screw supplied, screw the utility hook (23) to the housing of the power tool (see figure E). ­ Check the utility hook (23) for damage or deformation.
Do not use the utility hook (23) if it is damaged, deformed or no longer firmly secured to the power tool. ­ Use the utility hook (23) to attach the power tool to a suspension device. To avoid damage or injury, the suspension device must not be attached above walkways or immediate work areas. The utility hook is intended solely for the purpose of hanging the power tool, including fitted accessories. u Never use the utility hook as a fall protection system.
Transport For transport, switch off the power tool; especially when using ladders or moving in an unusual stance or posture. Lock the trigger with the unlocking switch (5). At the workplace, carry the power tool only by the handle (7) and with the trigger (6) released.
User interface
The user interface is used as follows:
– For switching the power tool on/off
– As the power tool status indicator
– As the battery charge indicator
– For resetting

Status indicators

Maintenance and Service

Maintenance and Cleaning

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

Rectifying Errors

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at: www.bosch- pt.com/serviceaddresses

Transport
The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further requirements.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 24).

EU Declaration of Conformity
Cordless nailer Article number
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.
Technical file at: *

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

References

• Invented for life | Bosch Global
• The domain name bosch.mk is for sale
• Početna strana | Bosch u Srbiji
• 巧米网为您服务！(QiaoMi.com)
• Skånevik Ølen Kraftlag AS
• Електроінструменти Bosch | Bosch Professional
• Электроинструменты Bosch | Bosch Professional
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Електроинструменти на Bosch | Електроинструменти на Bosch
• Service worldwide
• Elektrické nářadí Bosch | Elektrické nářadí Bosch
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Scule electrice Bosch | Scule electrice Bosch
• Bosch električni alati | Bosch električni alati
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Invented for life | Bosch Global
• Ana Sayfa | Bosch Türkiye
• Početna | Bosch u Hrvatskoj
• herramientasbosch.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>