HERCULES 63761 13 Piece Hole Saw Set Owner’s Manual
- June 4, 2024
- Hercules
Table of Contents
HERCULES 63761 13 Piece Hole Saw Set
IMPORTANT SAFETY INFORMATION
- Wear ANSI-approved safety goggles and heavy-duty work gloves during setup and use.
- Set contains sharp blades. Keep away from children.
- Use correct size Mandrel for selected Hole Saw.
- Verify drill’s chuck is in good condition and fits securely.
- Do not use excessive pressure when cutting a hole.
- Use as intended only; do not modify tools.
- Inspect before every use; do not use if parts are loose or damaged.
- Use both hands when drilling and keep blade at 90° to workpiece.
- Store saw blades in Case in secure location away from children.
- Read and adhere to all safety warnings and operating instructions of drill used with Set.
- The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator
SPECIFICATIONS
Saw Sizes| 3/4″, 7/8″, 1-1/8″, 1-3/8″, 1-1/2″,
1-3/4″, 2″, 2-1/8″, 2-1/2″
---|---
Other Pieces| Large Mandrel Small Mandrel 2 Pilot Bits
1 Hex Key
SETUP
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
CUATION
TO PREVENT INJURY:
Wear heavy-duty work gloves and ANSIapproved safety goggles during setup and
whenever handling the saws.
SMALL MANDREL SETUP
-
Insert Pilot Bit into Small Mandrel with the flat strip along the bottom of the bit facing the Hex Key hole on the Mandrel.
-
Insert Hex Key into hole and twist clockwise to secure the Pilot Bit.
-
Select the desired size Hole Saw for the Small Mandrel.
Note : Only the 3/4″, 7/8″, and 1-1/8″ Hole Saws can be used for the Small Mandrel. -
Thread Hole Saw onto Collar Thread until secure.
-
Open Jaws of Drill Chuck (sold separately).
-
Place the Mandrel Shaft completely into the Chuck and securely tighten the Chuck.
LARGE MANDREL SETUP
-
Insert Pilot Bit into Small Mandrel with the flat strip along the bottom of the bit facing the Hex Key hole on the Mandrel.
-
Insert Hex Key into hole and twist clockwise to secure the Pilot Bit.
-
Pull down the knurled Locking Collar to retract the Locking Pins.
-
Thread Hole Saw onto Collar Thread until the Locking Pins align with the Holes in the Saw. Make sure the Saw is threaded tightly and the holes are properly aligned.
Push up the knurled Locking Collar to extend the
-
Locking Pins through the holes in the Hole Saw.
-
Hole Saw should be secure. If loose, repeat Step 5 and make it tighter while keeping the holes aligned.
-
Open Jaws of Drill Chuck (sold separately).
-
Place the Mandrel Shaft completely into the Chuck and securely tighten the Chuck.
LIMITED 90-DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no
event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our
product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to
you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take
advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of
the complaint must accompany the merchandise. If our inspection verifies the
defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide
you with a replacement. We will return repaired products at our expense, but
if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning
the product. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Record Product’s Serial Number Here:
Note : If product has no serial number, record month and year of purchase
instead. Replacement parts are not available. Reference UPC 792363637619.
Visit our website at : http://www.harborfreight.com
Email our technical support at:
productsupport@harborfreight.com
For technical questions, please call
1-888-866-5797
Copyright© 2021 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>