V380 Pro App User Manual

User Manual V1.1

Key Introduction

APP Download

Scan he QR code belowi, Download V3SOPro APP or Mobile Mall Download V380Pro APP, nsalla- tion and Registration Login.

http://www.av380.cn/v380procn.php

Networking Tutorial

WiFi mode (remote mode)

• take note of: It is recommended to charge the camera for 1-2 hours after receiving it-Yellow light is always on when charging, yellow light is off when fully charged
• If the camera equipment is abnormal, Please reset the camera to reset,
  Press and hold the “MODE” button for 3-5 seconds and then release it.At this time, the blue light will blink two times fast (means the reset is successful), The light color changes again to a slow blinking blue light on- ly.The camera is reset successfully

1. Press and hold the “ON/OFF” button for 3-5 seconds and release it, The light will come on at this time, wait for the blue light to flash slowly.
2. Open V380 Pro APP, After clicking on the “+” in the upper right corner, Scan the QR code on the machine to access the matching page
3. Enterthe currently available WIF and its password and click OK.
4. Please use the camera lens to scan the QR code on the cell phone page (15-20cm distance), Press “Hear Success Tone” below when the blue light is on, Waiting for devices to bind to the network.
5. After successful binding, the page will automat- ically jump to, Please follow the prompts to set the device name and customize it by entering the password.

AP hotspot mode (proximity mode)
Note: It is recommended to charge the camera for 1-2 hours after receiving it, the yellow light is always on when charging, and the yellow light is off when fully charged.
If the camera device is abnormal, please reset the camera reset, long press the “MODE” button for 3-5 seconds and then release it, at this time, the blue light will flash two times (on behalf of the reset is success- ful), the light color changes again to only the blue light flashes slowly, it means that the camera reset is suc- cessful

1. Long press the “on key” 3-5 seconds to release, this time the light will come on, to be blue light slow flashing
2. Open the cell phone WiFi list and connect to the WiFi signal starting with “MV*”, e.g. MV43999723. (Figure 1) Reminder:** prox- imity mode with- out networking, the theoretical distance of about 30 meters (open without interfer ence, blocking), according to the actual environ- ment test shall prevail.
3. Open V380 Pro APP, in the device list interface scroll down will pop up to discover devices, click add device, customize the device password and then you can start using it. (Figure 2)

Setting up the camera for remote monitoring

1. click on the upper right corner of the preview screen , and then click “Settings”.
2. Go to the Settings screen and select “Change device network”. (Figure 3)
3. After entering the interface, click “Switch Device to Routing Mode” at the bottom of the in- terface. (Figure 4)
4. Select “Click here to change WiFi”, choose your WiFi and enter the password to switch to remote.

FCC warning:

1. This device should be installed and operated with minimum distance 20cm between the radiator&your body.

2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and
   (2) This device must accept any interference received, including interference that may cause undesired operation.

3. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

4. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a_ residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
   —Reorient or relocate the receiving antenna.
   —Increase the separation between the equipment and receiver.
   —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   —Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>