Fretta SJ-009 Cold Press Juicer Machines Instructions

Fretta SJ-009 Cold Press Juicer Machines Instructions

SPECIFICATIONS

Voltage 100-120V~50-60Hz;
Power 200W
Juice cup capacity 800ml
Pulp container capacity 700ml
Unit size 7.56.215.8 inch
Bare weight 5.5LB

IMPORTANT

1. The Unit is designed for household use only.
2. Commercial users will not obtain the regular warranty as stated in thetermsof the warranty card.
3. This is not a toy. Please do not let children play with it or use it.

IMPORTANT SAFEGUARDS

1. Make sure the electricity supply is suitable for this unit.
2. This unit is intended for household use only. Do not use the unit at outdoorsorfor other purpose than intended.
3. Use the unit only as described in this manual.
4. To prevent from electrical shock, do not immerse the unit, cord set andpluginto water.
5. This is not a toy and not to be used by children. Close supervision isrequiredwhen the unit is used near children.
6. Ensure to unplug the unit when not in use, assembling or disassembling, and before cleaning.
7. The continuous operation time of this product should be within 20minutes.
8. No-load or overloaded operation of machine is prohibited.
9. Do not touch or move any moving parts during operation of machine.
10. Do not use finger, spoon or chopsticks to push fruits or vegetables intothechute of machine. Only pusher is allowed.
11. Do not open the unit when it is operating.
12. Do not place the unit near any explosives, heated oven or hot surfaces.
13. Operate the unit only on flat surface.
14. Do not let the cords hang over the edge of table or the like.
15. Please hold the plug to disconnect from the power socket.
16. If the parts of product structure is found to be damaged (especially thesafetydevice and power cord), please stop using and send it to service centretoberepaired by qualified technician.
17. This product is not intended operated by persons (including children) withweakphysical condition, slow reaction, mental retardation, lack of experienceandcommon sense, unless they are under supervision or instruction bythepersonwho is responsible for their safety

NOTE

To avoid hazard of electric shock, unplug the unit from power outlet whennot inuse or before cleaning. If the supply cord is damaged, stop using immediately and bring it back to service center for repair.

PARTS DIAGRAM

1. Feeding Chute Cover
2. Squeezing Auger
3. Juicing Bowl
4. Power base
5. Switch
6. Juice cup
7. Pulp cup
8. Pusher
9. Cleaning brush

USING FORFIRSTTIME

1. Remove all packaging materials, plastic bags and labels.

2. Make sure the electricity supply is 100-120V~60Hz.

3. Clean the feeding tube cover/squeezing auger/juice cup/pulp cup/ juicingbowl/ pusherwith soapy water. Then rinse and dry thoroughly.
   NOTE : DO NOT IMMERSE THE POWER BASE UNIT INWATER.

4. Assemble the parts per the instruction in the assembling method section.

5. Connect the power cord to the power source.

The unit is ready to use now

ASSEMBLINGMETHOD

Please make sure the unit is not plugged and the switch is turned to “OFF”settingprior to assembling the machine.

1. 1. Position the squeezing bowl on the Power base aligning the position of thespoutsand the axle. (Fig 1)

2. Push the squeezing auger firmly into the center of the bowl, making sure that it
   touches down the bottom, or else the cover cannot be closed. (Fig 2)

3. Position the chute on the bowl to align the ▲ to the “ ” and twist it clockwiseuntil it clicks the safety lock. Please make sure that the arrow▲on “ ”thecover aligns with the Lock graphic on the Bowl. (Fig 3)
   

4. Place the juice container and the pulp container under the relevant spouts. (Fig4)

OPERATION INSTRUCTION

1. Connect the unit with Power.
2. Check and make sure all parts are well assembled in correct position.
3. Make sure the machine is at off “OFF” position.
4. Make sure the juice and pulp containers are in position.
5. Make sure the juice spout cover is closed.
6. Prepare the fruits or vegetables and cut them into pieces max 5cmx3cmstripsor5cm x 5cm cubes.
7. Put fruit strips/cubes into the chute.
8. Press the switch to Setting “ ON” to start the juicing operation.
9. Push the food down with the pusher only.
10. In case of food stuck inside the Bowl, please switch to “REV” reverse function instantly.

NOTE : Please do not use the juicer continuously longer than 20 minutes.

Open & Close of Juice Spout Cover

During the juicing process, you could keep the Drip-stop Cover closed beforethejuiceis full in the juicing bowl. (Fig 5)

Self feeding hopper slow juicer SJ-029C

BENEFITS OF DRIP-STOP COVER :

1. To stop dripping at the end of juicing.
2. To mix the juice with different fruits and vegetables.

USAGE TIPS :

1. Remove hard pits or seeds prior to pressing to prevent possible damage tothesqueezing screw.
2. If mixed juices are to be made, please begin with harder fruit, and thensqueezethe soft fruit.
3. Please let the juicer to run for 30 seconds after the last ingredient wasted.

ATTENTION :
The juicer is not suitable for juicing very hard or fibrous and starchy fruits or vegetables such as Sugar Cane. There are some fruits which contain too much starch tojuice. Some examples are Avocado, Bananas, figs, Mango, Papaya, Dragon Fruit, Strawberry, Grape without seeds etc. They will clog up the stainless steel sieve.

DISASSEMBLINGMETHOD

NOTE :
If the juicer gets overheated, it will turn off automatically to protect the machine. In this case, please turn the juicer off “OFF” . Wait 10 minutes to let the juicer cool down and then turn it on again.

To disassemble the unit after use and before cleaning. Please turn the juicer to “OFF”position and disconnect the juicer from power source. Then, please follow the steps below

1. Remove the Juice and Pulp containers. (Fig 6)

2. Remove the Chute. Turn the chute anti-clockwise until the ▲aligns withthe
   “ ” sign. (Fig 7)

3. Remove the Squeezing Auger by pulling it out upward. If it is very hard, swing gently and pull. (Fig 8)
   

4. Remove the Squeezing Bowl by lifting it upward vertically. (Fig 9)
   

CLEANING &MAINTENANCE

IMPORTANT

Please wash the juicing parts every time immediately after each used, otherwisethepulpmight stick tightly in Juicing Bowl & Squeezing Auger which will then affect the disassembly, cleaning and juicing performance.

1. Switch off and unplug the juicer.

2. Wash the disassembled parts (Fig 10) with water. If the meshes are clogged with pulp, pleaseusethe provided cleaning brush to remove the dregs.
   Attention :

   • Do not use iron wire brush, abrasive or sharp object tool to clean the unit.
   • Please do not use water above 40°C.

3. In case there is any residues remained in the mouth of the pulp spout, please pull out the silicone valve as shown in (Fig 11) below and clean under running water.

Press the silicone valve to close it property and tightly after cleaning

4. To clean the seal ring in the center of the squeezing bowl, please follow the steps as below : a. Turn the Squeezing Bowl upside down for easier handling, Push the seal rigout with your thumb (Fig 12a) and clean it with water.

b. After Cleaning, please put it back to the center hole. The small ribbed surface should be should face upward (Fig.12b) Make sure the groove of the seal ring well fit in the squeezing bowl.

c. The big flat size of the seal ring will be inside while the small and ribbedsideis outside the Squeezing Bowl. (Fig 12c)

5. Do not put the Power Base into water for cleaning. Wipe it with damp cloth only.
6. After cleaning, please dry the parts thoroughly and store them in a dry, cool place

STORAGE

1. Follow cleaning instructions to well maintain the unit before storage.
2. Tidy up the power cord set.
3. Keep the unit away from children’s easy access.
4. Store the unit and the accessories at a dry, cool place.

NOTE :
Please make sure the unit and parts are dry before storing it.

USEFUL TIPS

parts.
2| The ingredient with long fiber needs to be cut down to 5-10 cm thin strips or 3 x 3 cm cubes.| Long fiber food is easy to wind and block the spout.
3| The peel and pits/seeds must be removed from oranges, lemons, grapefruit and melons before use.| The hard pit or seeds may damage the squeezing parts. The peel may block the spout of pulp.
4| Do not use other accessory as a pusher.| It may damage the juicer and cause injury.
5| Each juicing cycle not longer than 20 minutes.| Working over time may cause damage to the motor.
6| Never put the spoon, chopsticks into the opening of the Chute, the juice and pulp spouts.| It may damage the juicer.

TROUBLE SHOOTING

Switch to “R” position instantly to make the ingredients return upwards. If the machine still stops running, please clean the machine before use
Hard fruits or vegetables have not been cut in small pieces.| Hard fruits and vegetables have not (such as carrot) shall be cut into thin strips or small cubes before putting into chute
The juice yield is low or juice flows out of the main housing.| The Bowl and the silicone valve are not installed properly.| Please re-install the Bowl silicone valve by referringtothe installation method.
Abnormal noise| Parts cause extrusion sound during squeezing| The sound is caused by extrusion of fruits and vegetables, which is normal phenomenon.
The Chute & Strainer Assembly cannot be opened| There is too much pulps inside the bowl.| Press switch to “R” settingtoeject the pulps backward.
There is hard foods stuck inside| Press switch to “R” to eject the object backward
The pulp mess is stuck.| Pour water into the Chute to often the stuck pulp mess overnight.
The container & accessories are dyed after use| Dyed parts are due to natural color of specific fruits/veggies| This is natural color and unavoidable.

Fretta
E-mail: support@frettajuicers.com
Web: https://frettajuicers.com/

References

• Fretta Juicers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>