HATHEVER PB-11B Dog Potty Training Doorbell User Manual
- May 15, 2024
- HATHEVER
Table of Contents
User Manual Dog Potty Training Doorbell
User Manual
Model: PB-11B/PB-21B/PB-22B/PB-31B
PB-11B Dog Potty Training Doorbell
Thank you for purchasing this product. To ensure proper use and trouble-free operation, please read this manual carefully and store it in a safe place for future reference.
Package Contents
Content will vary according to
your kit
The push button supplied with this kit is pre-programmed to operate with the
doorbell. If it is not, see “Pairing method”.
Overview
Technical Specifications
| Receiver working voltage | AC 110 V – 220 V |
|---|---|
| Sound pressure level | ≤ 110 dB |
| Receiver AC power consumption | < 0.5 W (Standby mode) |
| Working frequency | 433.92 MHz |
| Transmitter battery type | 12V 23A battery |
| Operating temperature | -20 °C – 60 °C |
| Battery lifetime | Up to 2 years |
Features
- Easily activate the dog training bell with a slight touch on the nose or paw.
- Enjoy 20 melodies with rich and crisp sound from the built-in stereo speaker.
- Use the bell from almost anywhere with a 300 m wireless distance range (depending on the environment).
- The IP65 weather-proof transmitter is suitable for various outdoor environments.
- Set different ring tones for each transmitter to identify which doorbell is being rung.
- The memory function remembers your previous melody and volume level for added convenience.
Installation
Transmitter battery replacement
Step1: Remove the protective cover with the plastic key, then take off the
screw with screwdriver and open the back cover. Step2: Replace the battery,
align position and fix the front cover, then tighten the acrews.
Note: The battery is pre-installed in the transmitter. Peel
off the insulating film on the button cell to active the transmitter.
Transmitter installation
- Adhesive tape: apply the double-sided adhesive tape on the back of the transmitter. Remove the outer side of the tape and attach the transmitter in the desired location on the wall and press hard for 30 seconds.
- Screws and anchors: there are two screw holes on the back of the transmitter; remove the back cover of the transmitter and fix the transmitter with the screws and anchors in the desired location on the wall.
Operating Instructions
Pairing method
- Plug the receiver into a power socket.
- Press the chime’s “music button” to select the music you want.
- Press and hold the “pair button/mode button” on the receiver for 3 seconds, until chime rings “bird sound” twice.
- Press the transmitter which you want to pair within 30s and the receiver will rings to indicate the paring is complete; if not, please press the transmitter again, until the chime rings.
To add more buttons/receivers, simply follow the above steps.
Note:
- Press and hold the chime’s “pair button/mode button” for about 10s, until chime rings “dingdong” twice, all the pairing code will be deleted completely.
- To change the melody, follow step 2 through step 4 for operating the doorbell.
Notification mode selection
This dog bell has four notification modes: 1) Ring only; 2) Light flash only;
3) Ring and light flash; 4) Ring and light on. Press the “pair button/mode
button” to choose the mode you want.
Volume adjustment
There are four volume levels. Press the “volume button” to select prefer
volume level. When the volume reaches its minimum, press the button again to
return to the maximum volume.
Notice
- Please do not place transmitters in areas close to metals.
- The working distance varies if there are blockages within the environment.
- Use this product properly to prolong its lifespan.
- To prevent destroying internal electronic components, never repair the interior circuit.
Customer service email:
hathever@126.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>