ULTRARM MA20P-S Heavy Duty Monitor Arm for Ultrawide Monitors User Manual
- May 15, 2024
- ULTRARM
Table of Contents
ULTRARM MA20P-S Heavy Duty Monitor Arm for Ultrawide Monitors
PRECAUTION & DISCLAIMER
WE HEREBY DISCLAIM ANY AND ALL LIABILITY FOR INJURY OR DAMAGE ARISING FROM INCORRECT ASSEMBLY, INCORRECT MOUNTING, OR INCORRECT USE OF THIS PRODUCT.
- Read the entire instruction manual before you begin installation and assembly. If you don’t understand the instructions or encounter any questions or concerns, please don’t hesitate to contact us. Incorrect assembly or installation can result in serious injury, death, or property damage.
- DO NOT assemble or install products or accessories if they are damaged or missing. If you need to replace any parts, please get in touch with us for assistance.
- We are not responsible for desktop damage due to overloading or accidents. Carefully open the carton, remove the contents, and place them on cardboard or other protective surfaces to avoid damage.
- We declare that we shall not be liable for any damage or injuries caused by any modification or improper installation of the product, installation beyond the specified weight-bearing range of the product, improper use of the product, or damage caused by the use of the product
- Check the package contents against the part list on the first page to ensure you have received all components undamaged. DO NOT use damaged or defective parts.
- Carefully read all instructions before attempting installation. DO NOT use this product for any purpose or in any configuration not explicitly specified in this instruction manual.
ASSEMBLY PROCESS & PART LIST
BASE & GROMMET MOUNT (ALTERNATIVE)
- Required Parts: A, B, C, D, E, F, G, Y, Z
Note: Before affixing the anti-slip pad, make sure to tighten the screws.
Note: Before affixing the anti-slip pad, make sure to tighten the screws.
- Attach to the top four holes designed for desk thickness ranging from 15mm to 58mm.
- Attach to the bottom four holes designed for desk thickness ranging from 50mm to 85mm.
ARMS
- Required Parts: A, J, K, L, X, Z
- The small screws are intended for securing the arms.
- Loosen them before inserting the arms and tighten them afterwards.
- Note: When removing the arms, be cautious as the small screw (Spares-1) may fall off.
- Remember to reposition it before reassembling the arms.
MONITOR
- Required Parts: M, Q, Y, VESA Screws, Screwdriver
For assembling a monitor larger than 32 inches, we highly recommend having two
people collaborate.
*Note: The VESA plate slot can be rotated once it is connected to the
monitor.
FINE TUNING MONITOR ARM
- Required parts: Z
TILT ADJUSTMENT
Tighten the two side bolts repeatedly until they correspond to the weight of
the screen.
Then, hold the middle of the screen’s upper and lower edges to adjust the tilt
angle.
Note: If unable to tighten, please refer to the next page for adjustment
instructions.
GAS SPRING ARM ADJUSTMENT
- Required parts: Y
TIP: For safe extension of the arms. we recommend using longer cables.
FAQ
- What’s causing the VESA plate misalignment?
- The VESA plate can be rotated to switch the monitor between portrait and landscape modes. Adjusting it is straightforward after the monitor is attached. Just grasp both sides of the monitor and rotate it to your desired position.
- Why is it difficult to change the arm’s height?
- The monitor arm is intended for screens. To make it easier to adjust, install the screen first to add weight, and then attempt to lower the arm.
- Can I tilt the monitor without tools?
- The tilt mechanism operates through friction. To adjust the tilt without tools, you must match the friction to the monitor’s weight.
- To achieve this, repeatedly tighten the two screws on the side of the VESA head until the friction is appropriate. Once properly tightened hold the monitor’s top and bottom in the middle to adjust the tilt angle.
The tilt mechanism is compatible with most monitors, except for 32:9 monitors and those larger than 43 inches, such as the Samsung Neo G9 49-inch monitors.
Two Monitors, Multiple Possibilities
Your VISION, Your Perfect Customization
For dual monitor stacking, ensure compatibility: 27″ – #2 – #3 > 0.
- VESA standard screen installation and arm connection interface.
- Lower screen height + half the upper screen height.
- Reserved space between the lower screen and desktop.
- For side-by-side dual monitors, ensure compatibility: #4 < 39.3″.
- The VESA interface distance between two monitors.
When calculating VESA screen distance, include the screen bezel.
Thank You for Choosing us!
- We appreciate your choice to follow your VISION.
- Your satisfaction is paramount, and we’re here to help.
- Share your feedback on Amazon to help others.
- For assistance, contact our friendly support.
- Your satisfaction drives our success.
CONTACT
- support@ultrarm.com
- facebook.com/ultrarm
- ultrarm.com
- 886-2-77143660
ULTRARM CO., LTD. All rights reserved.
- All specifications subject to change without notice.
- Trademarks used herein are the property of ULTRARM CO., LTD. or of their respective owners.
- MA2OP-S V3.0 240110-1105
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>