tp-link SM311LS Mini Gbic Module Installation Guide
- May 15, 2024
- tp-link
Table of Contents
Installation Guide
MiniGBIC Module
Install the SFP
- Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.
- Insert the SFP into the SFP slot and firmly press it into place.
- Remove the protective dust plug from the SFP.
- Plug fiber-optic cables into the SFP. Note that the SFP works without any additional configuration.
Note:
- Do not touch the output pins on the transceiver with your hand.
- Always keep the protective dust plug on the SFP’s optical bores until you are ready to make a connection.
Caution:
DO NOT point or stare directly into the beam or into the optical port of the
transceiver when it is operating, as this can injure your eyesight.
Remove the SFP
- Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.
- Disconnect the network fiber-optic cables from the SFP.
- Pull the safety latch downwards to release the SFP, and then pull it out from the slot.
- Reinstall the protective dust plug in the SFP’s optical bores and place it on antistatic mat or a static shielding bag.
Connection
Only use the same transceiver model between switches for fast and reliable
connectivity.
For simplicity, we will take SM311LS as an example.
Specifications
General Specifications
Normal | SM311LS | 850 nm |
---|---|---|
Wave Length | 1310 nm | SM311LM |
Standards and Protocols | IEEE 802.3z, TCP/IP | |
Cable | Single-mode Fiber | Multi-mode Fiber |
Fiber Type | 9/125 um Single-mode | 50/125 um or 62.5/125 um Multi-mode |
Max. Cable Length | 20 km | 550m |
Data Rate | 1.25 Gbps | |
Port Type | LC Duplex | |
Power Support | 3.3 V | |
Safety & Emission | FCC, CE | |
DDM | Ye s | |
SFP-MSA | Ye s | |
Hot Swappable | Ye s |
Environmental and Physical Specifications
Product Operating Temperature | 0˚C to 70˚C (32˚F to 158˚F) |
---|---|
Storage Temperature | -40˚C to 85˚C (-40˚F to 185˚F) |
Operating Humidity | 5% to 90% RH, Non-condensing |
Storage Humidity | 10% to 90% RH, Non-condensing |
TP-Link Compatible Products
- TP-Link Switches with gigabit SFP Slots
- MC220L
Note:
The SFP modules may be incompatible with other vendors’ devices. We recommend
that you use only TP-Link SFP modules on your TP-Link devices.
General Specifications
Fiber Type | SM311LS |
---|---|
Data Rate | 1310 nm |
Port Type | IEEE 802.3z, TCP/IP |
Normal | Single-mode Fiber |
Wave Length | 9/125 um Single-mode |
Standards and Protocols | 20 km |
Cable | 1.25 Gbps |
Max. Cable Length | LC Duplex |
Power Support | 3.3 V |
Safety & Emission | FCC, CE |
DDM | Ye s |
SFP-MSA | Ye s |
Hot Swappable | Ye s |
Environmental and Physical Specifications
Product Operating Temperature | 0˚C to 70˚C (32˚F to 158˚F) |
---|---|
Storage Temperature | -40˚C to 85˚C (-40˚F to 185˚F) |
Operating Humidity | 5% to 90% RH, Non-condensing |
Storage Humidity | 10% to 90% RH, Non-condensing |
TP-Link Compatible Products
- TP-Link Switches with gigabit SFP Slots
- MC220L
Note:
The SFP modules may be incompatible with other vendors’ devices. We recommend
that you use only TP-Link SFP modules on your TP-Link devices.
Explanation of the symbols on the product label
symbols may vary from products
Symbol | Explanation |
---|---|
Class II equipment | |
Class II equipment with functional earthing | |
Alternating current | |
Direct current | |
Polarity of d.c. power connector | |
For indoor use only | |
Dangerous voltage | |
Caution, risk of electric shock | |
Energy efficiency Marking | |
Protective earth | |
Earth | |
Frame or chassis | |
Functional earthing | |
Cauti on, hot surface | |
Cauti on | |
Opera tor’s manual | |
Standby | |
ON/”OFF” (push-push) | |
Fuse | |
Fuse is used in neutral N | |
RECYCLING |
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the
environment.
User has the choice to give his product to a competent recycling organization
or to the retailer when he buys a new electrical or electronic equipment.
| Cauti on, avoid listening a t high vo l ume l evels for l ong periods
| Disconnection, all power plugs
m| Switch of mini-gap construction
m| Switch of micro- gap construction (for US version)
Switch of micro-gap / micro-disconnection construction (for other versions
except US)
ε| Switch without contact gap (Semiconductor switching device)
FCC compliance information statement
Product Name: Minibus Module
Model Number: SM311LS
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp.linkcom/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above
has been shown to comply with the applicable technical standards, FCC part 15.
There is no unauthorized change is made in the equipment and the equipment is
properly maintained and operated.
Issue Date: 2023/07/21
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant
provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/support/ce/.
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016.
The original UK declaration of conformity may be found at https://www.tp-
link.com/support/ukca/.
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
Do not point or stare directly into the beam or into the optical port of the
transceiver when it is operating, as this can injure your eyesight
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
http://www.tp-link.com/support
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit https://www.tp-
link.com/support, or simply scan the QR code.
References
- Link: Simple, secure one-click payments
- TP-Link Community
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
- WiFi Networking Equipment for Home & Business | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>