FDI ELI50-CPW 5.0 Inch PCAP Touch Screen LCD Module User Manual
- May 15, 2024
- FDI
Table of Contents
- Important Legal Information
- Introduction
- Recommended Accessories (Purchased Separately)
- Touchscreen Precaution
- ESD Warning
- Determining the Revision of your ELI
- Technical Specifications
- Mechanical Details
- Connectors
- Power Details
- Touch Activity LED
- Extended Display Information Data (EDID)
- PWM Control of Backlight
- Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DI ELI50-CPW 5.0 Inch PCAP Touch Screen LCD Module
Important Legal Information
Information in this document is provided solely to enable the use of Future
Designs, Inc. (FDI) products.
FDI assumes no liability whatsoever, including infringement of any patent or
copyright. FDI reserves the right to make changes to these specifications at
any time, without notice. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical, for any
purpose, without the express written permission of Future Designs, Inc. 996 A
Cleaner Way, Huntsville, AL 35805.
Microsoft, Windows, Windows 10 are registered trademarks of Microsoft Corporation. Other brand names are trademarks or registered trademarks of their respective owners.
Printed in the United States of America.
For more information on FDI or our products please visit www.TeamFDI.com. ©2023 Future Designs, Inc. All rights reserved.
FDI Document PN: MA00105 Revision: 1.0, 11/20/2023
Introduction
About ELI (the Easy LCD Interface)
ELI® is Future Designs, Inc.’s family of long-life, plug-and-play embedded
displays. ELI products are true modular embedded display solutions that
require no engineering or lead-time.
All ELI products are compatible with a wide range of single board computers
including Raspberry Pi, BeagleBone Black and Windows-based units. FDI designed
ELI as an embedded display option that requires minimal development time to
help customers reach production quickly. Once a product is in production,
FDI’s 10 to 15 year ELI product availability guarantee helps ensure production
schedules without the risk of expensive or time consuming redesigns. Learn
more about ELI at TeamFDI.com/ELI.
ELI Compatibility
ELI products are compatible with most Single Board Computers, PCs, and
operating systems.
See https://www.teamfdi.com/product-details/eli50-cpw#compatibility for the
results of FDI’s compatibility tests with popular operating systems and
platforms. Our results, as indicated in the table, demonstrate ELI versatility
but the table is not exhaustive. ELI products are designed to work with any
single board computer that has an HDMI or DP output. To submit a question
about ELI compatibility with a platform or operating system that is not
included in the table, contact a member of the FDI support team at
Support@teamfdi.com.
Your ELI Experience
Share your experience connecting ELI devices to various (single board) computers at: http://www.teamfdi.com/edid/#edidform.
Recommended Accessories (Purchased Separately)
- 7.5V to 17V DC (+/- 5%) Power Supply, with a center positive barrel connection.
- Power Input Cable (FDI P/N: ELI50-CPW-PIC) available from DigiKey or Mouser.
- Or build your own Power Input Cable using these items.
- 2.1mm I.D. x 5.5mm O.D. Jack to Screw Terminal, on DigiKey PN: 1528-1386-ND
- 4-pin, 1.5mm Molex connector for power input, Molex PN: 502578-0400
- 24AWG 225mm, male-male Molex cables for power input
- Red Molex PN: 2157102125
- Black Molex PN: 2157101125
- See Figure 3. ELI50-CPW-PIC Power Input Cable for a visual reference.
Note: All ELI units operate from +12V DC so this is the recommended power supply input voltage for the entire Family. See section 9.0, Power Details, for more information.
- USB Type A to Mini Type B Cable (for touch)
- HDMI Cable (Type A Male)
- Lengths for the USB and HDMI cables will be determined by the ELI mounting location and position in each user application.
Touchscreen Precaution
When the ELI50-CPW is powering up and initializing, please refrain from touching the front of the display or laying it face down on a surface. This can interfere with proper touchscreen initialization and may cause temporary issues with the touch screen operation. If this condition occurs, please reset, or power up the unit correctly and normal touchscreen operation will resume.
ESD Warning
Figure 1. Electrostatic Sensitive Device
Our ELI units are shipped in a protective anti-static package. Do not subject the module to high electrostatic potential. Exposure to high electrostatic potential may cause damage to the boards that will not be covered under warranty. General practice for working with static sensitive devices should be followed when working with this device.
Determining the Revision of your ELI
All ELI devices have a label placed on the board to identify the part number and revision of the unit. This label will help you quickly and correctly identify your ELI unit’s part number and revision number.
An example of an ELI label is shown below.
Technical Specifications
Table 1. Technical Specifications
Screen Size (diagonal inches): | 5.0 |
---|---|
Display Technology: | a-Si TFT LCD |
Resolution: | 720 x 1280 (WXGA Portrait) |
Brightness (nits typical): | 300 |
Contrast Ratio (typical): | 1000:1 |
Aspect Ratio: | Tall 9:16 |
Interface Input Mode: | HDMI |
Colors: | 16.7M (24 bit) |
Horizontal Viewing Angle: | 85/85° |
Vertical Viewing Angle: | 85/85° |
Surface: | 1.1 mm anti-fingerprint treated glass |
Touch Screen: | Projected Capacitive |
Touch Screen Interface (mA typical/max): | USB Device |
Touch Panel Hardness: | 6H |
Active Area (in mm, W x H): | 62.10 x 110.40 |
Response Time (ms): | 30 |
Backlight: | 12 LEDs |
Backlight Life (K hours typical): | 30 |
Backlight Power Consumption (W Typical): | Up to 61% of total |
Operating Temperature: | -20° to 70° C |
Storage Temperature: | -30° to 80° C |
Input Voltage: | 7.5 to 17 VDC +5% |
Power Consumption (mA, typ/max): | 150/250 @ 12V |
USB Power Consumption (mA, typ/max): | < 1mA (touch is powered from 12V) |
RoHS Compliant: | Yes |
Dimensions (in mm W x H x D) | 71.61 x 145.36 x 6.26 |
Mounting: | 3M 300LSE tape or other 3M tape |
Weight (grams) | 94 |
Mechanical Details
A 2D Mechanical Drawing of the unit is available on our website under the
Documentation tab.
https://www.teamfdi.com/product-details/eli50-cpw
3D Mechanical Models (in both STEP and EASM format) are available from our
website after
completing a simple fillable NDA or Non-Disclosure Agreement.
https://www.teamfdi.com/mechanicalmodelrequest
Connectors
Power Details
A 12VDC +/- 5% power supply with a 2.0A output will power most any product from the ELI Family. This allows a common, off-the-shelf power supply such as the 1939-1462-ND to be used for quick demos or prototyping across the entire ELI Family. In general, any 12VDC power supply with a 2.1mm center positive connection will be acceptable if it can provide enough current to power the particular ELI unit being used.
On the ELI50-CPW, a Power Input Cable is available to help easily power the
unit for prototyping and testing. This cable is available from
DigiKey or
Mouser under P/N ELI50-CPW-PIC or you
can build your own using the information given below and in Section 2.0,
Recommended Accessories (Purchased Separately).
When ready, connect power via the cable into the power connector (J6).
Pin | Value |
---|---|
1 | Positive Power Input |
2 | Positive Power Input |
3 | Ground |
4 | Ground |
Mating Connector Details for J6:
- Manufacturer: Molex
- Part Number: 502578-0400
- Digi-Key Housing Link
- Pre-terminated wires:
- Digikey Red Link
- Digikey Black Link
LED4 is the “Power” LED indicator that is on if the ELI is connected to a DC input voltage.
LED1 is the “LCD Power” indicator and LED3 is the “LCD 6V0 Power” Indicator. When DC input power is applied to the unit (via J6) and an HDMI input signal is present at J2, LED1 and LED3 will turn ON (LED1 is Orange and LED3 is Yellow). This LCD Power indicator only confirms that a DC input voltage and an HDMI signal are “present” at the ELI50-CPW inputs, but it does not mean that the input signals are necessarily valid or correct.
ELI50-CPW units can use power supplies ranging from +7.5 to +17.0 VDC + 5% (2.0A).
For volume production applications, the input power can be optimized for your
ELI unit and lower capacity power supplies can be used.
To verify that the ELI50-CPW unit is correctly powered you may check the input
voltage with a Fluke multi-meter or scope by probing test point TP5, shown
below. Please verify that the input voltage is present, and within the +/- 5%
tolerance and is free from excessive noise or AC ripple.
Note: If using an input that is within the 7.5V to 17.0V (+/- 5%) range
of an ELI50-CPW, the voltage measured from TP5 will reflect the input voltage
being utilized.
Note on Proper Power Up Sequence:
The ELI50-CPW must be powered on before the SBC video source to ensure that the EDID information can be read properly to auto initialize the correct screen resolution and timing.
Some Single-Board Computers or other HDMI video sources might only read the EDID information when the video source is first powering up, so it is critical to make sure that the ELI50-CPW is powered up first to assure proper initialization of the video / screen resolution.
Touch Activity LED
ELI50-CPW has a Touchscreen Activity LED (LED2) located near the USB touch
Interface (P2):
This Green LED2 will stay on when the USB touch interface is connected and
blink whenever any touchscreen input is detected, allowing for verification of
the touch response.
Note that no touch response will be read if the HDMI is disconnected, or the
ELI display is not detected by the video source.
Extended Display Information Data (EDID)
ELI uses Extended Display Identification Data (EDID) for automatic configuration with many operating systems. You can find out more on our website at http://www.teamfdi.com/edid/.
The ELI50-CPW must be powered on before the SBC video source to ensure that the EDID can be read properly.
Some Single-Board Computers or other HDMI video sources might only read the EDID information when the video source is first powering up, so it is critical to make sure that the ELI50-CPW is powered up first to assure proper initialization of the video / screen resolution.
PWM Control of Backlight
NOTE: For Rev 1.x units the PWM feature is not implemented but will be supported in future revisions.
J4 mating connector housing information:
- Manufacturer: Hirose
- Part Number: DF12-3S-1.25C
- Digi-Key Link: https://www.digikey.com/products/en?keywords=H2180-ND
- Pre-terminated wires https://www.digikey.com/en/products/filter/jumper-wires-pre-crimpedleads/453?s=N4IgjCBcoLQCxVAYygMwIYBsDOBTANCAG4B2aWehA9lANogDsAHAG wgC6hADgC5QggAvsKA
ELI provides an input, so an external processor or SBC can control the backlight to vary the display brightness or to reduce power consumption (the display backlight is typically one of the larger sources of power consumption in the unit). PWM dimming is an input with a 0 to 3.3 VDC range and the user should drive this with a push-pull type output or a suitable open collector output.
To control the display, backlight the user should connect an externally generated Pulse Width Modulated (PWM) signal to J4 pin 2 along with a common ground to J4 pin 3. The frequency range for this signal is from 5KHz to 100KHz. Each ELI unit’s display backlight properties will vary, so the user should test their version for an acceptable range of brightness control. For example, your 0 to 100% brightness range may be 40% to 90% of the PWM range. In certain installations, a series resistor on J4 pin 2 may be required to ensure a clean PWM signal is provided to the ELI. The suggested value for the resistor is 100ohms. See Figure 9 below, for example of connectivity. Actual testing in your installation may require this resistor to be changed, or possibly not required at all.
On the ELI unit, the PWM dimming signal is pulled up to LCD_VDD providing 100% backlight power when no PWM signal is applied at pin 2 of J4. If nothing is connected to J5 the ELI will drive the display at 100% brightness (default).
The LCD_VDD output at pin 1 of J4 is a 3.3VDC ± 5%. If the external system is
capable of directly driving the PWM dimming signal at 3.3VDC, there is no need
to connect pin 1 to the cable. ELI provides the 3.3 VDC signal, called
LCD_VDD, for the external system in case this voltage is needed to generate
the correct levels on the PWM dimming input.
The ELI backlight can be easily controlled from a Raspberry Pi. See Figure 9 for a wiring diagram. Our software is available on the website at https://www.teamfdi.com/product-details/eli50-cpw#software or you may copy the code from here:
As an example, the ELI backlight can also be controlled from a Renesas Synergy
S7G2 wired as shown in Figure 11. The software for Synergy can be found on our
website at https://www.teamfdi.com/product-details/eli50-cpw#software.
Support
Where to Get Help
Online technical support is available at http://www.teamfdi.com/support/
Useful Links
13.2Useful Links
Future Designs, Inc. Forums:
https://www.teamfdi.com/forums/
ELI50-CPW Product Page: http://www.teamfdi.com/product-details/eli50-cpw
ELI Software User’s Manual: http://www.teamfdi.com/wp-content/uploads/ELI-
SoftwareUsers-Manual.pdf
Tell us about your ELI experience: http://www.teamfdi.com/edid/#edidform
EDID Information Page: http://www.teamfdi.com/edid/
Copyright ©2023, Future Designs, Inc
References
- ELI - FDI - Future Designs Inc.
- airspayce.com/mikem/bcm2835/bcm2835-1.52.tar.gz
- Home - FDI - Future Designs Inc.
- Home - FDI - Future Designs Inc.
- Extended Display Identification Data (EDID) - FDI - Future Designs Inc.
- Extended Display Identification Data (EDID) - FDI - Future Designs Inc.
- ELI - FDI - Future Designs Inc.
- 5.0″ PCAP Touch Screen LCD Module – ELI50-CPW - FDI - Future Designs Inc.
- Support - FDI - Future Designs Inc.
- Home - FDI - Future Designs Inc.
- 368 Adafruit Industries LLC | Connectors, Interconnects | DigiKey
- ELI50-CPW-PIC Future Designs Inc. | Computer Equipment | DigiKey
- 2157101125 Molex | Cable Assemblies | DigiKey
- 2157102125 Molex | Cable Assemblies | DigiKey
- 5025780400 Molex | Connectors, Interconnects | DigiKey
- 5025780400 Molex | Connectors, Interconnects | DigiKey
- Jumper Wires, Pre-Crimped Leads | Electronic Components Distributor DigiKey
- DF13-3S-1.25C Hirose Electric Co Ltd | Connectors, Interconnects | DigiKey
- Extended Display Identification Data (EDID) - FDI - Future Designs Inc.
- Index - FDI Forums
- 3D Models and EASM Request - FDI - Future Designs Inc.
- 5.0″ PCAP Touch Screen LCD Module – ELI50-CPW - FDI - Future Designs Inc.
- 5.0″ PCAP Touch Screen LCD Module – ELI50-CPW - FDI - Future Designs Inc.
- 5.0″ PCAP Touch Screen LCD Module – ELI50-CPW - FDI - Future Designs Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>