Fdi Shenzhen Representative Office J803L2 BT Headphone User Guide
- June 6, 2024
- Fdi Shenzhen Representative Office
Table of Contents
BT earphone
Packing list
Diagram
- Volume control LO
- Volume control down
- Power on/ off
- 3.5mm jack
- power Indicator
- TYPe-C throng port
- Mcrconcno
- ROB light charge button
- ROB light
Charge battery
While the Bluetooth headset is charging, the Power Indicator will show a Red LED light until fully charged. Once fully charged, the light indicator will be Blue.
Power on / off &Game mode
1. Power on Press and hold the ” ‘ for 3 seconds, then the headphone will
turn on with the prompt “Power on’ and the Blue/ Red LED light will flash.
2. Power off: Press and hold the “ ” for 5s, then the headphone will turn off
with prompt “Power off’ and Red LED will light on for 2s then off.
3. Game mode: Please dick the three times to enter the low-latency mode,
which will be turned on with a ‘Di’ voice. Click the power button three times,
the game mode will be turned off with the “DuDu” voice.
How to pair
Connect for the first time:
1. Press and hold the power button for about 3 seconds, the unit will power
on, at the same time will enter pairing mode: you can hear voice tone ‘
pairing.” Then see the LED light blinks blue and red (between Aux in the hole
and Type-C charging hole).
2. Turn on Bluetooth on your device(mobile, PC, tablet, etc), enter the
Bluetooth list, searching, when seeing 1.1803L2’ on the list, click it to
connect the headset with your device. Once successfully paired, you can hear
the voice tone ‘connected’.
Music Play
- Press: Music Play / Music Pause
- Press the “+” button: Short press’+’ button for Volume Up; Long press “+” button for Next Track
- Press the button. Short press the “-” button for Volume Down; Long press button for Previous Track
Calling ( Mobile Phone)
- Short pressing power button to receive or end a call.
- The long pressing power button for about 2s to reject a call.
- Press and hold the button for 2 seconds: Voice Assistance
- Double clicks power button for redial last call number
- Short press the ‘+’ button (Voice “Di when maximum volume): Volume Up
- Short press the “-‘ button(Voice “Du” when minimum volume): Volume Down
RGB Light
Technical Data Sheet
| Type | Feature | Description or Detail |
|---|---|---|
| BT | Pair name | ‘.1803L2’ |
| Operated distance | Over 15m | |
| Frequency Range | 2402-2480 MHz | |
| Speaker | Diameter | 040 +/- 0.3 mm |
| --- | --- | --- |
| Frequency Response | 20Hz-20KHz | |
| Impedance | 320 +1-15% | |
| Sensitivity/S.P.L. | 115±3 dB(at 1K Hz, IEC318 test) | |
| Rated Power | 10mW | |
| Battery | Type | Chargeable Li-ion Battery |
| --- | --- | --- |
| Capacity | 750 mAh |
FCC STATEMENT
1.This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For a Class B digital device or peripheral, the instructions furnished the
user shall include the following or similar statement, placed in a prominent
location in the text of the manual:
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>