PHILIPS InstantFit LED Lamps Installation Guide

: May 15, 2024
: Philips

Table of Contents

Installation Guide
- InstantFit TLEDs
- Philips InstantFit LED Lamps
Documents / Resources
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Guide

InstantFit TLEDs

PHILIPS InstantFit LED Lamps 0

InstantFit 2′
InstantFit 3′
InstantFit 4′
InstantFit U-Bent
InstantFit PL-L

The Installation Guide contains important information and notes regarding the installation and operation of the InstantFit lamps.
Please note the important points below:

– Not compatible with luminaires that use a remote starter.
– Modifications to the product void the warranty.
– Suitable to replace fluorescent lamps as specified on the product label.
– Must be installed with ballast which is listed in Philips TLED compatible ballast list.
– Please refer to www.philips.com/instantfit for latest ballast compatibility guide.
– Verify TLED dimming compatibility on the ballast compatibility guide.

For Philips InstantFit LED Lamps — 2′,3′,4′,8′

1 2 Fluorescent 3 Fluorescent

4 LED InstantFit 5 LED InstantFit 6

For Philips InstantFit LED Lamps — U – Bent

1 2-3 Fluorescent 4 InstantFit LED

5 InstantFit LED 6

For Philips InstantFit LED Lamps — PL-L

1 2-3 Fluorescent 4 InstantFit LED

5 InstantFit LED 6

See reverse side for installation instructions.

Philips InstantFit LED Lamps

Instructions

1. Switch-off power to the luminaire
2. Remove diffuser (if provided)
3. Remove the existing fluorescent lamps from the luminaire.
– Note: Verify the fluorescent tube type is listed on the label of Philips InstantFit LED lamp.
4-5. Install the Philips InstantFit LED lamp (one for each fluorescent lamp removed’, ensure pins are firmly seated in the lamp holders).
– For U bent & PLL, please ensure that the lamp is secured by the clip.
– Replace diffuser (if removed in step 2).
6. Switch on power to the luminaire.

CAUTION – IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BU77ING, FLICKERING, ETC ), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER

CAUTION – RISK OF FIRE. DO NOT INSTALL IN A PRE-HEAT LUMINAIRE

THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS. IF LAMP DOES NOT LIGHT WHEN THE LUMINAIRE IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE AND CONTACT LAMP MANUFACTURER OR QUALIFIED ELECTRICIAN

CAUTION – RISK OF FIRE. PERFORM A VISUAL INSPECTION TO ENSURE LAMPHOLDERS ARE NOT DAMAGED OR LOOSE. IF DAMAGED, CORRODED, CHARRED, BLACKENED, OR LOOSE, CONTACT A QUALIFIED ELECTRICIAN FOR PROPER REPLACEIMENT.

TYPE A LAMP – Intended for direct substitution of a fluorescent lamp and operating from the integral ballast without any modifications to the fluorescent luminaire.

This device complies with part 18 of the FCC Rules.

THIS PRODUCT MAY CAUSE INTERFERENCE TO RADIO EQUIPMENT AND SHOULD NOT BE IN STALLED NEAR VARITIME SAFETY COMMUNICATIONS EQUIPMENT OR OTHER CRITICAL NAVIGATION OR COMMUNICATION EQUIPMENT OPERATING BETWEEN 0.45 – 30MHZ.

THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS STANDARD(S). OPERATION IS SUBJECT TO THE FOLLOWING -WO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION OF THE DEVICE.

LAMPS MUST BE OPERATED WITHIN AN AMBIENT FIXTURE TEMPERATURE OF -4F (-20C) AND 113E (45C) TO ENSURE UL COMPLIANCE.

This Class A digital apparatus complies with Canadian ICES-005.

THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS or NOT FOR EMERGENCY LIGHTING.

¹(N-1) rule applies, meaning:
Minimum 3-lamps be replaced in a 4-lamps ballast.
Minimum 2-lamps be replaced in a 3-lamps ballast.

Signify reserves the right to make changes in specifications and/or to discontinue any product at any time without notice or obligation and will not be liable for any consequences resulting from the use of this publication.

09/2021 www.philips.com/lighting
Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.

Signify North America Corporation
400 Crossing Blvd, Suite 600
Bridgewater, NJ 08807, USA

Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3

3241 653 18525