DTS TENORE 3 New Generation Profiler with Linear User Manual

DTS TENORE 3 New Generation Profiler with Linear

Specifications

• Product Name: TENORE 3/5 HDW – SOPRANO 3/5 HDW
• Release: 1.0.2
• FW. version: 1.0.1
• Language: EN
• Code: 0517I368

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. Illuminazione

D.T.S. Illuminazione reserves the right to make any aesthetic, functional, or design modifications to any of its products without prior notice. D.T.S. Illuminazione takes no responsibility for the use or application of the product circuits described herein.

DMX Signal Connection

• The unit operates using the digital USITT DMX512 signal.
• The connection between the light controller and the projector, or between projectors, must be carried out using a two-pair screened ø 0.5 mm cable, and an XLR 5 or 3 pins connector.
• Ensure that the conductors do not touch each other. Do not connect the ground cable to the XLR chassis. The housing of the plug must be isolated.
• Connect the light controller to the DMX IN panel connector of the projector; to create a link to the next projector, simply connect the DMX OUT plug of the former to the DMX IN plug of the new fixture in line.

Following this procedure, all the projectors will be cascade-connected.

• DMX signal not present

• DMX reception problem

• The use of a DMX terminator is recommended.

• The DMX terminator is a male XLR 3- or 5-pins connector with a 120 Ω resistor between pin 2 and pin 3.

• The DMX terminator must be plugged in into the last unit’s DMX OUT panel connector of the DMX line.

• Place a 120 Ω resistor between pins 2 and 3 of a male XRLconnector;

• Plug the resistor into the DMX OUT panel connector of the last unit connected to the DMX line.

DMX Modes

TENORE 3/5 HDW – SOPRANO 3/5 HDW can be used in two different DMX modes:

• CCT (Default) – Dimmer 16-bit with Correlated Color Temperature and Green saturation control.
• Basic – Dimmer 8-bit with Correlated Color Temperature control e.g., when using the unit in “CCT” (Default) mode (6 DMX channels), set the following addresses on the light desk
• Projector 1 A001
• Projector 2 A007 If you want to select the next projector, just add “6” to the former DMX address
• Projector 3 A013 ….. A….
• Projector 6 A031

Setting Up the DMX Address

1. Rotate the jog wheel until you reach the desired DMX address. The numbers on the display will start flashing (the new DMX address hasn’t yet been set).
2. Push to confirm your selection. The numbers on the display will stop flashing; the projector is now set to the new DMX address.

RDM Functions

• By using an RDM controller, it is possible to read/set DMX addresses, DMX modes, and other parameters.
• TENORE 3/5 HDW – SOPRANO 3/5 HDW accepts the following RDM commands:

RDM version: ANSI E1.20 –2010

RDM DEVICE MODEL ID

0710:0D8Cxxxx (Tenore/Soprano 3 HDW)
0710:0D8Bxxxx (Tenore/Soprano 5 HDW)
RDM PID DESCRIPTION| RDM PID VALUE| GET| SET
Category – Network Management| | |
DISC_UNIQUE_BRANCH| 0x0001| |
DISC_MUTE| 0x0002| |
DISC_UN_MUTE| 0x0003| |
Category – Status Collection| | |
STATUS_MESSAGES| 0x0030| X|
STATUS_ID_DESCRIPTION| 0x0031| X|
Category – RDM Information| | |
SUPPORTED_PARAMETERS| 0x0050| X|
PARAMETERS_DESCRIPTION| 0x0051| X|
Category – Product Information| | |
DEVICE_INFO| 0x0060| X|
DEVICE_MODEL_DESCRIPTION| 0x0080| X|
MANUFACTURER_LABEL| 0x0081| X|
DEVICE_LABEL| 0x0082| X| X
SOFTWARE_VERSION_LABEL| 0x00C0| X|
---|---|---|---
Category – DMX512 Setup| | |
DMX_PERSONALITY| 0x00E0| X| X
DMX_PERSONALITY_DESCRIPTION| 0x00E1| X|
DMX_START_ADDRESS| 0x00F0| X| X
Category – Sensors| | |
SENSOR_DEFINITION| 0x0200| X|
SENSOR_VALUE| 0x0201| X| X
Category – Dimmer Settings| | |
CURVE| 0x0343| X| X
CURVE_DESCRIPTION| 0x0344| X|
OUTPUT_RESPONSE_TIME| 0x0345| X| X
OUTPUT_RESPONSE_TIME_DESCRIPTION| 0x0346| X|
MODULATION_FREQUENCY| 0x0347| X| X
MODULATION_FREQUENCY_DESCRIPTION| 0x0348| X|
Category – Power/Lamp Settings| | |
DEVICE_HOURS| 0x0400| X|
LAMP_HOURS| 0x0401| X|
Category – Display Settings| | |
DISPLAY_INVERT| 0x0500| X| X
Category – Control| | |
IDENTIFY_DEVICE| 0x1000| X|
Category – Custom PID| | |
NO DMX ACTION| 0x9002| X| X
FANS SETTING| 0x903A| X| X
DISPLAY STANDBY| 0x903C| X| X
CROSSFADE CURVE| 0x903D| X| X
GREEN SATURATION EXCURSION (from FW. version 1.01)| 0x9047| X| X

FURTHER RDM MESSAGES

GAMMA CORR.” graphics

RDM MANUFACTURER’S SPECIFIC PIDs

FANS SETTING

| 0: Fan mode STANDARD

1: Fan mode SILENT (DEFAULT)

2: Fan mode ULTRA-SILENT

3: Fan mode AUTO

NO DMX ACTION

| 1: KEEP LAST (DEFAULT)

2: BLACKOUT

3: SINGLE CUE

4: PROGRAM01-16

DISPLAY_STANDBY

| 0 = DISABLED

1 = ENABLED (DEFAULT)

2 = FORCED ENABLED

GREEN SATURATION EXCURSION

(from FW. version 1.01)

| 0: NORMAL = ±0.01 (DEFAULT)

1: EXTENDED = ±0.02

---|---

RDM STATUS MESSAGE IDs:

Status Message ID| Data Value 1| Data Value 2| Status ID Description
---|---|---|---
0x8008| | | ERROR SUPPLY VOLTAGE TOO LOW
0x8009| | | ERROR SUPPLY VOLTAGE TOO HIGH
0x801F| | | ERROR TEMPERATURE LED MODULE
0x8020| | | ERROR TEMPERATURE LED DRIVER
0x8021| | | ERROR TEMPERATURE MICRO

Updating the Firmware

In order to update the unit to the latest firmware release, you will need:

• DTS firmware uploader dongle (code 03.LA.206).
• “DTS Firmware Upgrade Utility” program (v.2.02 or later) installed on PC (Windows OS).
• The latest firmware release is available for the unit.

Updating to the latest firmware release:
To perform the update, please follow the procedure as described below:

1. Connect the DTS Firmware Uploader Dongle to a spare USB port on the PC.
2. Connect the unit’s DMX IN to the DTS Firmware Uploader Dongle’s DMX OUT with a standard DMX cable and turn on the fixture.
3. Send the new firmware release into the unit by using the “DTS Firmware Upgrade Utility” program.
   During software upgrades, the LEDs will blink.
   At the end of the procedure, the unit will reboot.
   For more information, please refer to an authorized DTS service center.

Display Functions

• The display panel shows all the available control menus.
• You can access the menus by clicking the jog wheel.
• Turning the jog wheel performs cycling through the menus.
• By selecting the available functions on these menus, you will be able to change the fixture’s settings and behavior.
• Beware that changing these settings may vary the operating functions of the unit so that it may not respond correctly to the signal given to it. Carefully read the instructions and tables below before carrying out any variations or selections.

Jog Wheel

0710:0D8Bxxxx (Tenore/Soprano 5 HDW)
DMX Personality IDs| 0x01 “CCT”**

0x02 “BASIC”

0X03 “UNO MODE”

__

HIGHLITE

| ENABLED| 1..3600/BACK| | Highlite function forces the fixture “FULL ON” for a user-selectable period before exiting automatically.

Default = 60s

BACK| |
__

__

__

__

__

DISPLAY

| FLIP| DISABLED / ENABLED

/ BACK

| | Reverses display’s reading depending on the mounting position.

Default = DISABLED

__

__

__

STANDBY

| __

__

DISABLED / ENABLED

/ FORCED ENABLED

/ BACK

| | __

DISABLED: Display stand-by disabled (Default). – ENABLED: Display goes OFF after 10 seconds.

-FORCED ENABLED: Display forced OFF even if control signal is missing or error messages are shown.

BACK| | | Back to Main Menu
__

__

__

__

MODE (DMX

personalities)

| CCT

6 channels

| | Allows to select CCT mode

(6 DMX ch.).

| Default.

Dimmer 16bit with Correlated colour Temperature (1800K to 10000K) and green saturation point selection.

BASIC

2 channels

| | Allows to select BASIC mode

(2 DMX ch.).

| Dimmer 8bit with Correlated colour Temperature (1800K to 10000K

selection.

UNO MODE

1 channel (from FW. version 1.01)

| | Allows to select UNO MODE (1 DMX ch.).| One DMX channel controlling Dimmer Intensity of the “Single Cue” with values selectable by user in “Manual Control > Single Cue” menu.
BACK| | | Back to Main Menu
__

__

__

__

__

__

__

__

__

LED

| __

__

SMOOTH

| __

__

OFF / 1..20 / BACK

| | Allows to select the value of delay (in ms) for DIMMER channel reaction to DMX dimming command.

OFF = Instant response.

4 = 100 ms smooth response (Default).

20 = 500 ms smooth response.

__

__

__

__

__

__

__

GAMMA CORR.

| __

QUADRATIC

| | Allows to set quadratic current output for LED (Default).

See “Gamma Correction” graphics for details.

__

GAMMA 2.2

| | Allows to set gamma curve 2.2 current output.

See “Gamma Correction” graphics for details.

__

S-CURVE

| | Allows to set S-curve to emulates light intensity characteristics of the tungsten halogen lamps.

See “Gamma Correction” graphics for details.

LINEAR| | Allows to set linear light output.

See “Gamma Correction” graphics for details.

BACK| | Back to LED Menu
MAIN MENU| LEVEL 1| LEVEL 2| LEVEL 3| FUNCTION
---|---|---|---|---
| __

FREQUENCY

| __

610 – 5000 HZ / BACK

| | Allows to adjust the PWM frequency value (Hz) in order to reduce flickering in the process of camera recordings. Range = 610 Hz – 5 KHz

Default = 1000 Hz

__

__

__

TUNGSTEN EMUL.

| __

__

__

DISABLED / ENABLED

/ BACK

| | Allows to enable Tungsten Emulation.

Default = Disabled

When Tungsten Emulation is enabled and CCT channel 2700k4200K, as you lower the output, the luminaire will mimic a 1000w tungsten lamp.

A Variation in the dimmer intensity will affect the colour temperature so as a

dedicated gamma correction and smooth values are applied.

BACK| | | Back to Main Menu
__

__

__

__

__

NO DMX ACTION

| Allows to set the desired unit’s behavior in case DMX signal is missing or not available
KEEP LAST DMX| | | Keep last valid DMX signal (Default).
__

BLACK OUT

| | | BLACK OUT
HOLD| 1…3600 sec| Hold time keeping last valid DMX signal before to go in black out.

Default=1s

SINGLE CUE| | | Single Cue with values selectable by

user in “Manual Control > Single Cue” menu.

__

PROGRAM 01-16

| | | 16 pre-programmed steps with Parameters, Speed Time, and Wait Time selectable by user in “Manual Control > PROGRAM 01-16” menu.
__

__

__

__

__

__

__

__

__

__

__

__

__

__

MANUAL CONTROL

| Manual Control forces the fixture to Dmx Personality 1 – CCT (6ch). DMX input signal is ignored.

If MASTER=DISABLED no parameters are transmitted via DMX Line.

If MASTER=ENABLED and no DMX is received, the fixture will transmit parameters on DMX line to the “SLAVE” units.

In case of MASTER enabled when DMX line is busy, error message “DMX LINE BUSY” will appear on display. When the Fixture is in MANUAL CONTROL>SINGLE CUE or MANUAL CONTROL>PRORAM 01-16, In case of

a power cycling, the fixture does restart in MANUAL CONTROL>SINGLE CUE / MANUAL CONTROL>PRORAM 01-16

__

__

__

SINGLE CUE

Dmx Pers 1: CCT

| Single Cue with parameters selectable by user
SHUTT| 0..255 / BACK| Default = 015
DIM MSB| 0..255 / BACK| Default = 255
DIM LSB| 0..255 / BACK| Default = 255
CCT| 0..255 / BACK| Default = 128
GREEN SATURATION| 0..255 / BACK| Default = 128
BACK| | Back to Manual Control menu
__

__

__

__

__

PROGRAM 01..16

Dmx Pers 1: CCT

| 16 pre-programmed steps with parameters, speed and wait time selectable by user.
__

ACTIVE STEPS

| __

01..16 /BACK

| Selecting how many Steps will run on the Program.

Min 1 – Max 16.

Default =16

__

STEP SELECTION 01..16

| SHUTT DIM MSB DIM LSB CCT

GREEN SAT.

| Default = 015

Default = 255

Default = 255

Default = 128

Default = 128

SPEED| 1..3600 / BACK| Step speed time

Default =10s

WAIT| 1..3600 / BACK| Step wait time

Default =10s

BACK| | Back to Manual Control Menu
MAIN MENU| LEVEL 1| LEVEL 2| LEVEL 3| FUNCTION
---|---|---|---|---
| __

__

__

MASTER

| __

__

DISABLE / ENABLED / BACK

| __

SURE (YES / NO)

..

DMX LINE BUSY

| If MASTER=ENABLED and no DMX is received, the fixture will transmit parameters on DMX line for “SLAVE” units.

In case of MASTER enabled when DMX line is busy, error message “DMX LINE BUSY” will appear on display.

Default=Disabled

ESC| | | Exit from Manual control
__

__

SLAVE

| Slave mode forces the fixture to Dmx Personality 1 – CCT (6ch) and DMX ADDR=1.

When Slave mode is selected, in case of a power cycling the fixture do restart in SLAVE mode.

__

__

SURE

| __

YES

| SLAVE MODE ON| Slave Mode active; fixture forced to

DMX personality “CCT 6ch” and DMX address 001.

ESC| Exit from Slave Mode
NO| | Back to main menu
__

__

__

__

__

__

FAN

| Standard / Silent / Ultra Silent: Fan Speed is constant.

Auto: Variable fans speed depending on detected temperature for Led module and led driver.

__

__

__

__

STANDARD / SILENT /   ULTRA SILENT / AUTO /

BACK

| | Tenore / Soprano 3 HDW:

Fan Standard: 24dBA @ 1m (100% power) Fan Silent: 23dBA @ 1m (100% power) Fan Ultra Silent: 22dBA @ 1m (91% power)

__

Tenore / Soprano 5 HDW:

Fan Standard: 34dBA @ 1m (100% power) Fan Silent: 29dBA @ 1m (87% power)

Fan Ultra Silent: 26dBA @ 1m (70% power)

__

Tenore / Soprano HDW all models: Auto: (100% power).

t < 40°C: fans OFF.

40°C < t < 75°C: fans from min to max speed.

__

Default=SIlent

__

DEFAULT SET

| __

SURE?

| YES| | To restore Factory Settings.
NO| | Exit without restoring Factory Settings.
__

__

__

__

__

__

__

__

SYSTEM INFO

| __

__

__

TEMPERATURE

| __

LED        25,0

MICRO 25,0

DRV-1   25.0

DRV-2   25,0

| | LED: LED temperature monitoring. MICRO: Micro controller of LED Driver board temperature monitoring.

DRV-1: output 1/3 of LED Driver board temperature monitoring.

DRV-2: output 4/6 of LED Driver board temperature monitoring.

SOFTWARE| V.1.01| | Firmware release
__

__

TIME COUNTERS

| RED            00001

GREEN      00001

BLUE           00001

AMBER      00001

CYAN          00001

LIME           00001

UNIT LIFE 00001 Hrs

| | Unit and LED channels life time.
__

RDM INFO

| RDM DEVICE ID:

0710:0D8Cxxxx / 0710:0D8Bxxxx

| | RDM ids
BACK| | | Back to main menu
EXIT| | | | Exit from Main Menu

“GAMMA CORR.” graphics

Error Messages

immediately goes in black-out.
TEMP. DRV| Output from 1 to 6 of LED Driver PCB temperature detected under -20°C or over 90°C.

Unit immediately goes in black-out.

TEMP. MICRO| Micro controller on LED Driver PCB temperature detected under -20°C or over 75°C.

Unit immediately goes in black-out.

SUPPLY VOLTAGE TOO LOW| PCBs input voltage <46,5Vdc.
SUPPLY VOLTAGE TOO HIGH| PCBs input voltage >49,5Vdc.
LED CALIBRATION DATA NOT PRESENT| ****

Led module not calibrated, led calibration data corrupted or incomplete.

LED CALIBRATION READ ERROR
LED CALIBRATION INCOMPLETE DATA

DMX Protocol

DMX Personality 1
DMX Personality 1: “CCT” mode (6 DMX channels) (default)

1. SHUTTER
2. DIMMER Msb
3. DIMMER Lsb
4. CCT (1.800K – 10.000K)
5. GREEN SATURATION
6. FIXTURE CONTROL

000-255

| Linear CCT from 1800K to 10000K

Relevant CCT values (GREEN SATURATION channel 5 @ 128) 1800K = 000

2700K = 079

3000K = 092

3200K = 100

4000K = 128

5000K = 156

5600K = 171

6000K = 180

6500K = 191

7000K = 202

8000K = 221

9000K = 239

10000K = 255

values selectable via “MANUAL CONTROL> PROGRAM 01-16 menu

183-184| NO DMX ACTION – SINGLE CUE

values selectable via “MANUAL CONTROL> SINGLE CUE menu

185-234| reserved
235-236| FAN MODE SILENT (Default)
237-238| FAN MODE STANDARD
239-240| FAN MODE ULTRA SILENT
241-242| reserved
243-244| FAN MODE AUTO
245-252| reserved
6| FIXTURE CONTROL
---|---
DMX value| Function

253-255

| SET FUNCTION TO DEFAULT:

-SMOOTH DIMMING = 4

-GAMMA = QUADRATIC

-FREQUENCY = 1000 Hz

-DISPLAY STANDBY = ENABLED

-NO DMX ACTION = KEEP LAST DMX

-FAN MODE = SILENT

-TUNGSTEN EMULATION = DISABLED

DMX Personality 2
DMX Personality 2: “BASIC” mode (2 DMX channels)

1. DIMMER
2. CCT (1.800K – 10.000K)

000-255

| Linear CCT from 1800K to 10000K Relevant CCT values

1800K = 000

2700K = 079

3000K = 092

3200K = 100

4000K = 128

5000K = 156

5600K = 171

6000K = 180

6500K = 191

7000K = 202

8000K = 221

9000K = 239

10000K = 255

DMX Personality 3
DMX Personality 3: “UNO MODE” (1 DMX channel)

• One DMX channel controlling the Dimmer Intensity of the “Single Cue” in the “Manual Control > Single Cue” menu. |
  • DIMMER Intensity of the “Single Cue” in the “Manual Control > Single Cue” menu

FAQ

• What should I do if the display shows errors related to DMXsignal?
  • If the display shows errors related to the DMX signal, it is recommended to check for the presence of the signal and ensure proper reception. Using a DMX terminator with a 120Ω resistor can help resolve these issues.
• How can I set up the DMX address for the unit?
  • To set up the DMX address for the unit, follow these steps:
  • Rotate the jog wheel to select the desired DMX address.
  • Press to confirm your selection and set the unit to the new DMX address.

D.T.S. Illuminazione S.r.l.

• ADDRESS: via Fagnano Selve, 12/14 47843 Misano adriatico (RN) Italy
• +39 0541 611131
• www.dts.lighting 
• info@dts-lighting.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>