OWNAIR 1800W Turbo Steam Iron for Clothes User Manual

OWNAIR 1800W Turbo Steam Iron for Clothes

INTRODUCTION

Thank you for your trust in OWNAIR TURBO. We pursue the highest standards of quality and design and hope you enjoy your new device.
Please read the instructions for use carefully and completely before using the device. Only use the device in accordance with the instructions for use and the safety instructions. Any other use may result in damage to the device or personal injury. The manufacturer assumes no liability for damage caused by improper use.

GENERAL SAFETY INSTRUCTIONS

• Please keep this manual, the warranty card, the proof of purchase and, if possible, the inner packaging.

• OWNER TURBO devices comply with the relevant safety regulations. Repairs and replacement of the connection cable may only be carried out by authorized specialist personnel. Improper repairs can result in considerable danger for the user.

• The device is intended exclusively for private and not for commercial use.
  Children must not play with the device. Cleaning and maintenance shall not be done by children.

• To protect children from the dangers of electrical appliances, never leave them unattended near the appliance. Choose a location for your device where children cannot access the device. Make sure the cable is not hanging down.

• For child safety, keep all packaging (plastic bags, boxes, polystyrene, etc.) out of the reach of children.

• The device can be used by people with limited physical, sensory or mental abilities or lack of experience/knowledge if they are supervised or have been instructed in the safe use of the device and have understood the resulting dangers.
  Keep the device and cord away from heat, direct sunlight, moisture, sharp edges, etc.

• Use the device only for its intended purpose.

• Only use original accessories.

• Always disconnect the appliance from the mains when you are not supervising it and before assembling, disassembling or cleaning it.

• Only connect the device to a properly installed safety socket. The cable and plug must be dry. The mains voltage must correspond to the voltage specified on the type plate of the device.

• Do not immerse the device in water or hold it under running water. If the device gets wet, unplug the power cord immediately. Don’t reach into the water.

• Do not use the device with wet or damp hands.

• Do not use the device outdoors.

• Do not leave the device unattended. When you leave the workplace, always switch off the device or pull the mains plug out of the socket.

• Turn off the device when cleaning or storing it. Always unplug the power cord from the outlet when the device is not in use and remove the supplied accessories.

• Check the device and cable regularly for damage. Do not use the device if it is damaged.

• Do not repair the device yourself, contact an authorized professional.

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person to avoid a hazard.

• For safety reasons, a broken or damaged cable may only be replaced with an equivalent cable from the manufacturer, our customer service or a similarly qualified person.

• Read the following sections, special safety instructions, use and cleaning carefully. In the event of misuse, incorrect handling or faulty repairs, no liability is accepted for any damage. Warranty services are also excluded in these cases.

SPECIAL SAFETY INSTRUCTIONS

• Turn the soleplate away from people when testing the steam output.
• Do not assemble or disassemble any components while ironing.
• Purified or distilled water should be used for ironing to increase service life.
• Do not turn on the device when water is poured out of or into the container.
• Never use the device on clothing that is currently worn on the body. Do not point the device at people or animals. Only use it in accordance with the safety regulations.
• Disconnect power to the device during filling and cleaning.

WARNING

To avoid electrical leakage and other hazards, turn off the power and unplug the power cord from the outlet before use and cleaning.

• The device must be replaced by a specialist of the manufacturer, its maintenance department, or a similar department in the following cases:
• If the device does not work as usual or shows damage such as leaks, e.g. B. was dropped.
• When internal parts, power lines, power cords and other components are damaged.

PART DESCRIPTION/TECHNICAL DETAILS:

1. Soleplate
2. Water tank
3. Device body
4. Indicator light
5. Handle
6. Steam ejection button
7. Power cord

TECHNICAL DETAILS

• Rated Power: 1800W Rated
• voltage: 220-240 V~ Rated
• Frequency: 50-60Hz
  Water Tank Capacity: 100ml

COMMISSIONING & USE

INSTRUCTIONS FOR FILLING THE WATER TANK

• The device itself can be put aside when filling the water tank. The water tank is filled by pouring water into it using a small measuring cup. Proceed as follows:
• Step 1: Hold the device with one hand and slide the water tank backwards to remove it.
• Step 2: Remove the water tank plug (a soft plug with a small grip)
• Step 3: Fill the water tank with water using a measuring cup, and then put the stopper back on

INSTRUCTIONS FOR ASSEMBLING ACCESSORIES

If you have purchased accessories and attachments for this product, you can read the following instructions for assistance. Proceed as follows:

• Step 1: Hold the device with one hand.
• Step 2: First, insert the two clamps installed on the device into the holes of the accessory
• Step 3: Then push the accessory into the top clamp. Important: If you want to change attachments after the device has heated up, you must wear heat-resistant gloves or take other protective measures to minimize the risk of scalding.

INSTRUCTIONS FOR FILLING THE WATER TANK

COMMISSIONING & USE
Read the following instructions to ensure safe use of the device:
BEFORE USING THE DEVICE
First, remove the water tank and fill it with a measuring cup. If possible, use purified or distilled water.
WHILE USING THE DEVICE

1. Make sure the power is on.
2. When the device is preheating, the indicator light will turn red and flash slowly, after preheating is complete,it will flash quickly.
3. Wait until the red indicator light starts flashing rapidly before you can use the device.

AFTER USING THE DEVICE

1. When using it for the first time, there may be a smell of burning, which is perfectly normal. After about 3-7 uses, however, this should wear off.
2. Make sure to turn off the power to the device after use. The device must not be left unused for a long period of time while the power cord remains connected.
3. If the device will not be used for more than three days, remove and empty the water tank.

STEAM CONTROL INSTRUCTIONS

This device has three steam levels and depending on the fabric, the appropriate selection must be made. Proceed as follows:

• Step 1 : Plug in the power cord until the red indicator light flashes slowly, indicating the heating-up phase has started. The indicator light flashes quickly when this is finished and the device is ready for use, the clothes can now be ironed. When you press the steam button, the red indicator light stops flashing, indicating that the maximum steam level is activated.
• Step 2 : The different steam levels are designed to move clockwise. The next steam level is selected when you press the steam button once.
• Step 3 : Choose the appropriate attachments for the respective substances to be treated. The red indicator light shows the maximum steam level, the green the medium and the blue the minimum level.

INDICATOR LIGHT

Steam release button

1. The red indicator light shows the maximum steam level.
2. The blue indicator light indicates the medium steam level.
3. The green indicator light shows the lowest steam level.

ANTI-DRY PUMPING FUNCTION

• After the water runs out, the device will detect this after the pump has pumped dry for 40-60 seconds. The red indicator light will start flashing rapidly and the pump will stop working.
• If you want to continue ironing, you need to refill the water tank and press the steam button to start the machine again. Depending on your needs, select the required steam level.

WARNING

1. The steam level cannot be selected or the steam ejection button cannot be adjusted when the indicator light flashes to indicate the heating status.
2. In the on state, if the water has been consumed for about 40-60 seconds and the pump has run dry, the machine will stop operating and enter the “anti-dry pump function’:
3. The steam ejection button is designed to move clockwise. The pump will stop working after the indicator light turns to the fast flashing status that the vapour is no longer emitted.

Instructions for ironing with the device Initial start-up

• Remove any labels or protective covers from the device, then straighten the cables and arrange them neatly before use.
• Before using the device for the first time, allow it to emit steam for a few minutes, this will remove all impurities and odours resulting from the manufacturing process.
• To avoid overloading the circuit, it is recommended not to use the same outlet as other electrical appliances. When you open the device box, review the list of all items and parts that you received.

OPERATION OF THE DEVICE

Remove the water tank and open it to fill about 100ml of water into the water tank with a measuring cup. (See instructions for filling the water tank).

• Plug in the power supply until the red indicator light comes on for heating up (about 25-35 seconds). During the heating process, it only flashes slowly. The device is ready to use when the red indicator light flashes quickly. There is no need to check the indicator light during the ironing process, instead continue ironing as usual.

IRON

• Hang the clothes on a hanger and flatten the clothes to be ironed with one hand while holding the device with the other hand.

• Press the steam button and press the steam holes firmly against the clothes, then iron from top to bottom. Thicker garments need to be ironed several times.

• The soleplate must be pressed tightly to the clothes (except for wool clothes}

• Move from top to bottom while ironing Danger

• A brush must be installed when ironing woollen clothes, and steam holes should not directly touch woollen clothes.

• If you need to take a break while ironing, place the appliance firmly with the steam holes facing up to avoid damaging the surfaces of other items.

USE OF THE ACCESSORY

• The fabric brush is suitable for removing dirt on clothes and cleaning woollen clothes, curtains, sofas, etc.
• No brush is required to iron wrinkled clothes. First, insert the lower part of the brush into the corresponding opening ofthe device and then push in the upper part of the attachment. The lint brush is suitable for removing dust, lint, etc.
• The cord clip is suitable for straightening cords and ribbons such as tie, collar and suspender straps.

AFTER EACH USE

1. When you finish working, turn off the power switch or unplug the power cord from the outlet.
2. Remove the water tank and empty the remaining water (into a sink or bucket).
3. Place the device on a flat surface and wait for it to cool down.

CLEANING, MAINTENANCE & STORAGE

DESCALE DEVICE

1. A common problem with steamers is that scale builds up in the steam chamber after using tap water for a long time. The method to reduce scale is to use filtered or distilled water.
2. If this is not possible for some reason, describe the device as follows, at least once a month:
3. Make sure that the device is disconnected from the mains and has cooled down completely. Add vinegar water to the water tank (ratio: white vinegar: water= 1:2).
4. After the device has been connected to the power supply and the heating-up phase is complete, press the steam release button and hold it down. Blow steam for about 5 minutes before stopping the steam blast.
5. Empty the remaining vinegar water from the water tank and rinse it with clear water until you can no longer smell the vinegar. Clean water can be refilled after 1 hour and the device can be used as usual.

PROPER MAINTENANCE

• Disconnect the device from the mains before cleaning it.
• Let the device cool down for about 15 minutes.
• Remove the water tank and empty it.
• When cleaning the device and accessories, make sure they have cooled down completely.
• Store the device in a safe, dry place.
• Use filtered or distilled water to extend the life of the device.
• Do not add detergent, chemical solution, salt water, perfume, dye and other liquids except pure water into the water tank. Many of them are flammable materials that can cause serious damage and injury. In addition,additives in the
• water can also damage or block the appliance’s steam system. Do not put spices in the water.

IRONING TIPS

• The laundry must be ironed inside out. When ironing, gently touch the clothes and iron them from different angles. Remove the wrinkles. It is important to keep the soleplate close to your clothes.
• This device is not suitable for removing dirt. However, this device can be used for dry cleaning of most materials (including silk, cotton, nylon, wool, etc.). Before use, please read the relevant material label of the clothing and check whether it can be treated with the appliance, as some clothing such as leather, synthetic skin, velvet, etc. cannot be ironed.
• To ensure your garment can be ironed, please test a small area inside first. If this does not cause any damage, you can continue.

TROUBLESHOOTING

TROUBLESHOOTING MAINTENANCE POLICIES

Documents / Resources

| OWNAIR 1800W Turbo Steam Iron for Clothes [pdf] User Manual
1800W Turbo Steam Iron for Clothes, 1800W, Turbo Steam Iron for Clothes, Steam Iron for Clothes, Iron for Clothes, Clothes
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>