Iconnect AHMC7292S IEEE802.11ah Module User Manual

May 15, 2024
iConnect

Iconnect AHMC7292S IEEE802.11ah Module

Iconnect-AHMC7292S-IEEE802-11ah-Module-PRODUCT

Specifications

General Features

  • Product Description: AHMC7292S IEEE802.11ah Module
  • Major Chipset: Newracom NRC7292 (268-pin CABGA)
  • Host Interface: USB / UART / SPI / I2C
  • Dimension: 30 x 51 x 4 mm
  • Form Factor: Full-size PCI Express Mini Card
  • Antenna: 1T1R 3.3VD
  • Operating Voltage: -40~70°C

RF Features

  • WLAN Standard: IEEE802.11ah
  • Frequency Range (US): 903.5-926.5 MHz
  • Modulation: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
  • Channel Bandwidth: 1/2/4 MHz
  • Output Power: 19.9dBm
  • Receiver Sensitivity: -106 dBm (MCS0@1MHz), -88 dBm (MCS7@1MHZ)

Product Usage Instructions

Overview
The AHMC7292S IEEE802.11ah module enables building long-range, ultra-low power WiFi networks in Sub 1 GHz license-exempt bands. It is suitable for applications like sensors and IoT devices.

Standalone Mode
In standalone mode, the device operates independently without external drivers. It requires a built-in firmware to define its routines and behaviors. Other devices can communicate with it through a UART interface using AT commands.

Connectivity
The AHMC7292S supports USB, UART, SPI, and I2C host interfaces for seamless connectivity with various devices.

Installation

  1. Insert the AHMC7292S module into a compatible slot on your device.
  2. Ensure proper alignment and secure connection.
  3. Install any necessary drivers or firmware updates as required.
  4. Power on your device to start using the module in standalone mode.

FAQ

  • Q: What is the operating temperature range of the AHMC7292S module?
    A: The operating temperature range is -40 to 70 degrees Celsius.

  • Q: Does the AHMC7292S module support multiple WLAN standards?
    A: No, the AHMC7292S module specifically supports the IEEE802.11ah WLAN standard.

  • Q: Can the AHMC7292S module be used in conjunction with external antennas?
    A: Yes, the AHMC7292S module can be connected to external antennas for enhanced signal range and performance.

Overview

AHMC7292S is the world’s first IEEE802.11ah module
The AHMC7292S IEEE802.11ah module series allows building of long-range, ultra- low power WiFi networks in Sub 1 GHz license-exempt bands. WiFi HaLow™ enables connectivity for many applications, including sensors and IoT devices.
The AHMC7292S supports for standalone mode, High data throughput and complete SDK, getting started with this new WiFi standard will be straightforward.

Standalone Mode
In this mode, the target device doesn’t need external drivers. It will be up and running by itself while powered on. Since it’s a self-running device, it requires built-in firmware to define its routines and behaviours.
Other devices can talk to this device through a UART interface, send AT commands and receive data with it.Iconnect-AHMC7292S-IEEE802-11ah-Module-
FIG- 4

Specifications

(US/FCC)

General Features Description
Product Description IEEE802.11ah Module
Major Chipset Newracom NRC7292 (268-pin CABGA)
Host Interface USB / UART / SPI / I2C
Dimension 30 x 51 x 4 mm
Form Factor Full-size PCI Express Mini Card
Antenna 1T1R
Operating Voltage 3.3VD
Operating Temperature -40℃~70 ℃
RF Features Description
--- ---
WLAN Standard IEEE802.11ah
Frequency Rage (US): Unit MHz 1MHz Bandwidth: 903.5-926.5 MHz

2MHz Bandwidth:

905-925 MHz

4MHz Bandwidth:

906-926 MHz

Modulation| OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Channel Bandwidth| 1/2/4 MHz
Output Power| 19.9dBm
Receiver Sensitivity| -106 dBm (MCS0@1MHz)

-88 dBm (MCS7@1MHZ)

(EU/CE)

General Features Description
Product Description IEEE802.11ah Module
Major Chipset Newracom NRC7292 (268-pin CABGA)
Host Interface USB / UART / SPI / I2C
Dimension 30 x 51 x 4 mm
Form Factor Full-size PCI Express Mini Card
Antenna 1T1R
Operating Voltage 3.3VD
Operating Temperature -40℃~70 ℃
RF Features Description
--- ---
WLAN Standard IEEE802.11ah
Frequency Rage (EU): Unit MHz 1MHz Bandwidth:

863.5, 864.5, 865.5, 866.5, 867.5

Modulation| OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Channel Bandwidth| 1MHz
Output Power| 13 dBm (Average Typical)
Receiver Sensitivity| -106 dBm (MCS0@1MHz)

-88 dBm (MCS7@1MHZ)

Antenna Information

(US/FCC)

Brand Model Name Antenna Type Connector
ALFA ARS-915P Dipole RP-SMA female
Frequency Range Gain VSWR Impedance
--- --- --- ---
902-928 MHz 0 dBi ≤ 2.0 50 Ω

(EU/CE)

Brand Model Name Antenna Type Connector
ALFA ARS-868P Dipole RP-SMA female
Frequency Range Gain VSWR Impedance
--- --- --- ---
863-870 MHz 0 dBi ≤ 2.0 50 Ω

NOTE : The antenna is just an optional accessory

Mini Card Golden Finger

Iconnect-AHMC7292S-IEEE802-11ah-Module-FIG- \(1\) Iconnect-AHMC7292S-IEEE802-11ah-Module-FIG- \(2\) Iconnect-AHMC7292S-IEEE802-11ah-Module-FIG- \(3\)

Reference Schematic

FCC Caution:

  • Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

  1. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

  2. A list of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It applies to the modular.

  3. Specific operational use conditions
    This module is stand-alone modular. If the end product will involve Multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, the host manufacturer have to consult with the module manufacturer for the installation method in the end system.
    The module is limited to OEM installation ONLY. The OEM integrators are responsible for ensuring that the end-user has no manual or instructions to remove or install a module.

  4. Limited module procedures: Not applicable

  5. Trace antenna designs: Not applicable

RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator& your body. If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by 2.1093.

Antennas
This radio transmitter FCC ID:2AB8772921 has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

  • Antenna type: Dipole Antenna
  • Maximum Antenna gain:0dBi

Label and compliance information
The end product must be labeled in a visible area with the following ” Contains FCC ID: 2AB8772921”

Information on test modes and additional testing requirements
The host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.

Additional testing, Part 15 Subpart B disclaimer
The host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15 B.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals