589 FABRICATION Canyon Frame Support Brackets Instruction Manual

589 FABRICATION Canyon Frame Support Brackets

Product Information

Specifications:

• Product Name: 2015-2022 Colorado/Canyon Frame Support Brackets
• Manufacturer: 589 Fabrication
• Location: Fenton, MI 48430

Product Usage Instructions

Tools Required:
Jack, Jack Stands, Marker, Wire Brush, Propane Torch, Welding Equipment

Installation Steps:

1. Jack the rear of the vehicle up and support it using proper Jack Stands.
2. Remove the rear wheels and tires.
3. Remove the manufacturing tab from the support brackets and grind any sharp edges smooth.
4. Place the Right-Hand Frame Support Bracket on the frame and align it with the matching hole.
5. Trace around the bracket with a marker on the frame.
6. Remove paint along the traced line on the frame to prep for welding.
7. Reposition the Frame Support Bracket onto the frame and clamp in place for alignment.
8. Tack weld the bracket onto the frame every three inches all around.
9. Fully weld the bracket onto the frame, spreading heat evenly across the bracket.

Frequently Asked Questions (FAQ)

• Q: Do I need to remove the fuel tank to install these brackets?
  A: It is recommended to remove the fuel tank on the left-hand side before welding, though not required. Be cautious of your surroundings when welding near the fuel tank.

• Q: Do I need to remove the bed of the truck for installation?
  A: No, you do not need to remove the bed to install these brackets. The installation can be done with the bed in place.

2015-2022 Colorado/Canyon
Frame Support Brackets

Tools Required

• Wire Brush
• Grinder
• 15mm Socket and Ratchet
• Floor Jack and Proper Jack Stands
• Welder
• Clamps
• Flat head Screwdriver
• Paint

Included in the kit:

• 1. Left-Hand Side Frame Support
• 1. Right-Hand Side Frame Support
• *Requires modifications to fit with Bison Fuel Tank Skid

Always fully read the instructions before beginning

• Please note: the left-hand side of the vehicle has the fuel tank located directly next to where you will be welding. However not required, we recommend that you remove the fuel tank before welding this side. It doesn’t take much time to remove.
• You do not need to remove the bed to install these. Our truck has a flatbed installed in these pictures.

Assembly

1. Step 1: Jack the rear of the vehicle up and support the vehicle using proper Jack Stands.
2. Step 2: With the vehicle supported on Jack Stands, remove the rear wheels and tires.
3. Step 3: Removed the manufacturing tab from the support brackets and grind any remaining sharp edges smooth.
4. Step 4: Locate the Right-Hand Frame Support Bracket and place it on the frame. The bracket will fit tight against the frame. Using the Small hole on the outer face of the bracket, align it with the matching hole in the frame. Once you are happy with the fitment and location of the bracket, trace around the bracket with a marker.
5. Step 5: With the bracket traced out on the frame, you can remove the paint along the line to prep for welding. Since the frame is fairly thin to start with, we recommend using a wire brush to remove any paint and not make the frame thinner from grinding. Using some heat from a propane torch can help soften the paint for easier removal. (Be aware of your surroundings when using an open flame)
6. Step 6 : With the frame cleaned up, reposition the Frame Support Bracket onto the frame and clamp in place, using the hole for alignment)
7. Step 7: Tack weld the Frame Support Bracket onto the frame, placing tack welds every three inches all the way around the bracket.
8. Step 8: Fully weld the Frame Support Bracket onto the frame, welding between the tack welds and moving around. You want to spread the heat out over the whole bracket. Take your time, you do not want to input too much heat into the frame.
9. Step 9: With the bracket fully welded and cooled, prep and paint any bare metal with a heavy duty paint.
10. Step 10: With the right-hand Frame Support Bracket completed, repeat steps 4 – 9 on the left hand side. Please note: the left-hand side of the vehicle has the fuel tank located directly next to where you will be welding. However not required, we recommend that you remove the fuel tank before welding this side. It doesn’t take much time to remove. You will need to support the fuel tank with a Floor Jack, remove the two 15mm bolts holding the fuel tank straps. Slowly lower the fuel tank down a couple inches so you can loosen the hose clamp on the filler tube and remove the wiring on the fuel pump.

589 Fabrication|Fenton, MI 48430

Documents / Resources

| 589 FABRICATION Canyon Frame Support Brackets [pdf] Instruction Manual
Canyon Frame Support Brackets, Canyon, Frame Support Brackets, Support Brackets, Brackets
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>