MOXA 5134 Series 2-Port Industrial NAT Device Installation Guide

MOXA 5134 Series 2-Port Industrial NAT Device

Overview

The MGate 5134 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP and PROFINET network communications.

Package Checklist

Before installing the MGate 5134, verify that the package contains the following items:

• 1 MGate 5134 gateway
• Quick installation guide (printed)
• Warranty card

NOTE: Please notify your sales representative if any of the above items is missing or damaged.

Optional Accessories (can be purchased separately)

• Mini DB9F-to-TB: DB9 female to terminal block connector
• WK-25: Wall-mounting kit, 2 plates, 4 screws, 25 x 43 x 2 mm

Hardware Introduction

LED Indicators

Ready

| Off| Power is off.

Green

| Steady: Power is on, and the MGate is

functioning normally.

Blinking (1 sec.): The MGate has been located by the Moxa utility DSU Location function.

Red

| Steady: Power is on, and the MGate is

booting up.

Blinking slowly (0.5 sec.): Indicates an IP conflict, or the DHCP server is not responding properly.
Flashing quickly Blinking (0.1 sec.): the microSD card failed.

PROFINET I/O

Device

| Off| No connection with PROFINET I/O controller.

Green

| Steady: PROFINET I/O is exchanging data, and Controller is in RUN mode.
Blinking (1 sec.): PROFINET DCP flash LED.

Red

| Steady: Incorrect slot configuration.
Blinking (1sec.): One or more connections timed out or in STOP mode.

Modbus RTU/ASCII/TCP

Client

| Off| No communication with the Modbus device.
Green| Steady: Normal communication in progress.

Red

| Blinking (1 sec.): Communication error.

1.    The Modbus slave device returned an error (exception).

2.    Received a frame error (parity error,

checksum error).

4.    TCP connection failed (only for Modbus

TCP).

ETH 1, ETH 2

| Green| Steady ON: Ethernet link on at 100Mbps.
Blinking: Data transmitting at 100Mbps.
Amber| Steady ON: Ethernet link on at 10Mbps.
Blinking: Data transmitting at 10Mbps.
Off| Link is down or not connected.

Dimensions

Reset Button

Restore the MGate to factory default settings by using a pointed object (such as a straightened paper clip) to hold the reset button down until the Ready LED stops blinking (approximately five seconds).

Hardware Installation Procedure

1. Connect the power adapter. Connect the 12-48 VDC power line or DIN-rail power supply to the MGate 5134’s terminal block.
2. Use a serial cable to connect the MGate to the Modbus device.
3. Use an Ethernet cable to connect the MGate to the PROFINET I/O controller.
4. The MGate 5134 is designed to be attached to a DIN rail or mounted on a wall. For DIN-rail mounting, push down the spring and properly attach it to the DIN rail until it “snaps” into place. For wall mounting, install the wall-mounting kit (optional) first and then screw the device onto the wall.

The following figure illustrates the two mounting options:

Wall- or Cabinet-mounting

We provide two metal plates to mount the unit on a wall or inside a cabinet. Attach the plates to the unit’s rear panel with screws. With the plates attached, use screws to mount the unit on the wall. The heads of the screws should be 5 to 7 mm in diameter, the shafts should be 3 to 4 mm in diameter, and the length of the screws should be over 10.5 mm.

Software Installation Information

Please download the User Manual and Device Search Utility (DSU) from Moxa’s website: www.moxa.com For using the DSU, refer to the User’s Manual. The MGate 5134 also supports login via a web browser.
Default IP address: 192.168.127.254
Create your administration account and password when you log in the first time.

Pin Assignments

Modbus Serial Port (Male DB9)

Ethernet Port (RJ45)

Power Input and Relay Output Pinouts

V2+

| ****

V2-

| |

V1+

| ****

V1-

---|---|---|---|---
DC

Power Input 2

| DC

Power Input 2

| ****

N.O.

| ****

Common

| ****

N.C.

| DC

Power Input 1

|

Specifications

Power Parameters

Power Input| 12 to 48 VDC
Power Consumption| 455 mA max.
Relays
Contact Current Rating| Resistive load: 2 A @ 30 VDC
Environmental Limits
Operating Temperature| Standard models: -10 to 60°C (14 to 140°F)

Wide temp. models: -40 to 75°C (-40 to

167°F)

Storage Temperature (package included)| -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity| 5 to 95% RH
Physical Characteristics
Dimensions| 25 x 90 x 129.6 mm (0.98 x 3.54 x 5.1 in)
Weight| 294 g (0.65 lb)
Reliability
Alert Tools| Built-in buzzer and RTC
MTBF|

ATTENTION

• Power terminal plug wiring size is 28-14 AWG, tighten to 1.7 in-lbs, wire min. 80°C. Use copper conductors only.
• This device is an open-type equipment and intended to be installed in a suitable enclosure.
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
•  When installing the device, the assembler is responsible for the securing the safety of the system in which the equipment is incorporated.

NOTE

• This device is intended for use indoors and at altitudes up to 2,000 meters.
• Pollution degree 2.
• Clean the device with a soft cloth, dry or with water.
• The power input specification complies with the requirements of SELV (Safety Extra Low Voltage), and the power supply should comply with UL 61010-1 and UL 61010-2-201.

For any repair or maintenance needs, please contact us. Moxa Inc.
No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan +886-03-2737575

References

• Moxa - Your Trusted Partner in Automation
• Moxa - Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>