OBABY R1-0-1 Astrid Cot Bed Instructions
- May 15, 2024
- OBABY
Table of Contents
Astrid Cot Bed
Instructions
Version: R1-0-1
IMPORTANT
KEEP FOR FUTURE REFERENCE
Safety Warnings
Thank you for choosing to be part of the Obaby family
Our Cot Bed confirms to BS EN 716-1:2017 and BS 8509:2008 + A1:2011. To ensure
that your cot bed is used in accordance with these instructions, please read
them fully.
Your child’s safety may be affected if you do not follow these instructions.
WARNING: A child’s safety is your responsibility.
WARNING: Assembly should be carried out by a competent adult only.
WARNING: Do not use more than one mattress in the cot bed.
WARNING: Do not place this child’s bed near heat sources, windows and
other furniture.
WARNING: Be aware of the risk of open fire and other sources of heat,
such as electric bar fires, gas fires, etc in the near vicinity of the cot
bed.
WARNING: Do not use this child’s bed if any part is broken, torn or
missing.
WARNING: Do not leave anything in the cot bed or place the cot bed close
to another product, which could provide a foothold or present a danger of
suffocation or strangulation, e.g. strings, blinds/curtain cords etc.
- This product is intended for use from birth up to 4 years old.
- Please be aware that the lowest base position is the safest and the base should always be used in that position as soon as the baby is old enough to sit unaided.
- The thickness of the mattress chosen should be such that the internal height (surface of the mattress to the upper edge of the cot frame) is at least 500mm when the base is set in the lowest position and a minimum of 200mm when the cot base is set in the highest position.
- We recommend you use the Obaby Mattress Size 140 x 70 cm for this cot bed. The mattress should be no more then 30mm shorter or narrower than the internal length or width of the cot bed.
- Regularly check that all fittings and compnents of the cot/bed are fully tightened and in working order.
- To prevent injury from falls, as soon as the child is able to climb out of the cot, it should be changed into the bed mode for use up until 4 years of age.
- The cot bed is designed to be dismantled for storage or transportation.
- Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be placed next to other furniture or windows, and should be placed either tight to the wall or have a gap of 300mm between the wall and the side of the bed.
- All assembly fittings should be tightened properly and care should be taken to ensure that no screws are loose, as a child could trap parts of the body, or clothing (e.g. ribbons, drawstrings, necklaces) this could lead to strangulation.
- During assembly children should be kept away from the product due to possible risk of injury.
- Wood is a natural material, the colour will darken with age.
- Use only spare parts approved by the manufacturer.
Routine care & maintenance Astrid
Care & Maintenance
For cleaning, use only a mild detergent and warm water.
◊ DO NOT USE BLEACH
◊ DO NOT USE any abrasive substances.
◊ From time to time, check your cot for loose screws, and worn parts. Replace
or adjust the parts as needed.
Due to constant updating and improvments, some components may occasionally
differ slightly from the images shown in these instructions. We reserve the
rights to change the specifications of any products without prior notice. If
you need any assistance please contact your Obaby retailer from whom you
purchased your product, who will take appropriate action.
If you are happy with your product & service from Obaby please leave a
review on our
Trust Pilot Page x
Parts List
You will require a cross head screw driver
Assembly
Converting into a Day Bed
Notes
OfficialObaby
obabyuk| obabyuk
OfficialObaby
---|---
https://www.obaby.co.uk/qr_redirect/more-info/Nika/Obaby-Nika-Changing-Unit- redirect-more-info.php