LOKBY High Pressure 10 Settings Shower Head with Handheld Set Instruction Manual

: May 15, 2024
: LOKBY

Table of Contents

THANK YOU
DIMENSION
how to use
Installation
care & cleaning
How to disassemble the bracket mount holder?
CUSTOMER SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LOKBY High Pressure 10 Settings Shower Head with Handheld Set

LOKBY High Pressure 10 Settings Shower Head with Handheld
Set

THANK YOU

Thank you for purchasing the Lokby 1O-setting handheld shower head. This manual gives you the information you need for a quick and easy installation. You are minutes away from enjoying a luxurious shower experience.

DIMENSION

Dimension

how to use

Spray selector: spray selector allows you to select from various spray patterns.

Stop button: Push the pause button to 5tOP the water flow

Wide jet: Tum the selector left
Regular Jet: Turn the selector right
Close Jet Spray: Tum the selector

components
4.7″ handheld shower head holder bracket shower hose installation video manual

prior to installation

unscrew the old shower head and remove all pipe tape as well.
ensure that the gasket from the old shower is not inside the shower pipe. Use a thin utensil to check inside the shower pipe for gaskets, such as a pencil or screwdriver. Do not check with your fingers.
you shouldn’t need any tools to unscrew the old shower head, but if the connection Is too tight to tum by hand, try to use a cr@Sc.ent wrench to get a better grip.

caution
Do not overtighten. Over-tightening a shower connection can make a leak much worse by damaging threads. Always try to hand-tighten the connections first If you need to use a wrench, don’t forces it Before tightening, place the piece of cloth over the connector nut to prevent the wrenches or pliers from scratching the finish.

Note:
The pause button reduces the water flow to a trickle but does not completely shut off the water. There will still be a drip. Note that this is by design to avoid pressure buildup and the potential of bursting the hose.

Installation

Make sure that a rubber washer with a mesh screen sits flat in the ball joint of the holder rocket. Screw the shower head bracket into the J-pipe. Hand-tighten clockwise to a snug fit. Do not overtighten.
Insert a rubber washer into the hex nut of the hose and gush it down flat. Connect it to the bracket, then hand-tighten.
Insert a rubber washer into the conical nut of the hose and push it down flat. Connect it to the handheld showerhead, then hand-tighten.
Place a handheld shower in the bracket holder. Rotate the bracket forward or back to adjust the spray angle. Turn on the water to test for leaks. If you F10 ice any leakage, 1t 1s ‘necessary to slightly tighten the connection.
If leakage does not stop by retightening the connections, use the Teflon tape to create a watertight seal. Wrap the threads in 2-3 passes of Teflon tape from the box. Remember to apply the tape from clockwise d1rect1on ~o avoid unwrapping 1t. Press the shower head tape firmly into the threads with your fingers with each wrap-around so that you can start to see them through the tape. Follow Step 2 under installation to reinstall the shower head.

care & cleaning

To maintain proper working conditions, dining ls required when mineral deposits appear on the spray orifices.
To remove mineral deposits, gently rub the nozzles on the face of the shower head to dislodge them.
To clean heavier deposits. remove the shower head and soak it face down In 1·2 cups of white vin (use white vinegar only) tor about 2•3 hours. Otherwise, it may damage the outer finish. If you want to soak it for longer, you can dilute the vinegar with water (ratio 1:1). Screw Into the shower head and run in each mode to flush out vinegar.
Do not clean or rinse any part with harsh chemicals, heavy-duty cleaners, or abrasives; this may damage parts or the finish and will void the warranty.

TROUBLESHOOTING GUIDE

PROBLEM| SOLUTION
no water flow from installed 5hower head|

confirm the previous show washer is not into the j-pipe.
confirm there is only one washer In the pivot ball.

low water’ force or missing spray patterns|

clean shower head In vinegar/water solution. (Seeca1e section).
clean filter screen.

leak at arm/pivot ball connection| A. confirm one single washer Is seated dome side up In each end of the shower hose. If It is worn, replace it.
B. grate a bar of soap across the J-pipe threads to act as a sealant.
showerhead sliding down or “falling forward”| A. try to disassemble the showerhead holder and retighten the connections.

How to disassemble the bracket mount holder?

Insert the rubber washer into the front section of the shower mount. The tapered side needs to face outwards.
Push the White split washer over the ball, making sure that the side with the lip Is facing forward (away from the back threaded end). The white washer should sit flat.
Place the ball joint inside the outer collar.
Screw the two parts of the bracket holder together.