YAMAHA SFP-SWRG-SX Network Switches Owner’s Manual

: June 4, 2024
: Yamaha

Table of Contents

General Specifications
Introduction
PRECAUTIONS
Handling and maintenance
Information
About disposal
Documents / Resources

SWITCH ACCESSORY
SFP-SWRG-SX
Accessories
Owner’s Manual

General Specifications

Product Number	SFP-SWRG-SX	SFP-SWRG-LX
Standards	IEEE802.3z,
1000BASE-SX	IEEE802.3z,

*1 Product performance may not meet specifications if the optical fiber or fitting are insufficient.

Introduction

Thank you for your purchase of switch accessory SFP-SWRG-SX/SFP-SWRG-LX. This product is an SFP module that, when connected to the SFP port of a Yamaha network
device, allows the use of 1000BASE-SX/1000BASE-LX. Be sure to read this Owner’s Manual before use and keep it in a safe place after reading it.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.

**WARNING:** Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short- circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Before installing this product in a device, check to make sure that the device is compatible with this product. Also, do not install this product in any Yamaha products not specified by Yamaha for use with this product in order to avoid possible electrical shock, fire, or device damage.
Do not attempt to disassemble or modify this product. Do not apply excessive force to connectors. Mishandling of this product may lead to shock, fire hazards, or device failure.
Do not place any burning items or open flames near the device, since they may cause a fire.

**CAUTION:** Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:

Be sure to properly ground the host device to prevent electrical shock and/or malfunction.
Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
Do not look at the laser light. This product uses a laser. Be careful to avoid looking at the ends of the optical fibers or the optical connectors. In the event you look at the laser, it may damage your eyes.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

Handling and maintenance

Correct communication might not be possible if debris and/or dust has adhered to the ends of optical fiber cables or the ports. Clean the equipment regularly by using commercially available optical fiber cleaning products.
Do not expose the product to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
Condensation can occur in the product due to rapid, drastic changes in ambient temperature—when the product is moved from one location to another, or air conditioning is turned on or off, for example. Using the product while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the product for several hours without turning on the power until the condensation has completely dried out.
Do not place vinyl, plastic or rubber objects on the product, since this might discolor the panel.
When cleaning the product, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Drain all static electricity from your clothing and body before handling this product.
Static electricity can damage this product. Touch an exposed metal part of the host device or other grounded object beforehand.
Do not drop this product or subject it to physical shock as this can result in breakage and/or malfunction.

Information

About functions/data bundled with the product
This is a class A product. Operation of this equipment in a residential environment could cause radio interference.
This product is a class 1 laser product. It is compliant with IEC/EN 60825-1, IEC/EN 60825-2,
FDA 21 CFR 1002.10, and 1040.10.
IEC 60825-1:2014
Factory: Axcen Photonics Corporation
6F., No.119, Baozhong Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)

About this manual
The illustrations as shown in this manual are for instructional purposes only.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

About disposal

This product contains recyclable components. When disposing of this product, please contact the appropriate local authorities.

Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery, and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
IMPORTANT: When connecting this product to accessories and/or another product use only high-quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “A” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product, in a commercial environment, will not result in harmful interference with other electronic devices. However, the operation of this product in a residential area is likely to cause interference in some form. In this case you, the user, bear the responsibility of correcting this condition. This product generates/uses radio frequencies and, if not installed and used according to the instructions found in the user’s manual, may cause interference harmful to the operation of other electronic devices. Compliance with regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either the product generating the interference or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna lead-in is 300-ohm ribbon lead, change the lead-in to a co- axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer that is authorized to distribute this type of product.
If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-3 (A)/NMB-3(A)

Manual Development Group
© 2018 Yamaha Corporation
Published 06/2021
2021
YJOD-B0

Documents / Resources

| YAMAHA SFP-SWRG-SX Network Switches [pdf] Owner's Manual
SFP-SWRG-SX, SFP-SWRG-LX, SFP-SWRG-SX Network Switches, SFP-SWRG-SX, Network Switches, Switches
---|---