Ultrasport Power Rack Fitness Rack Multifunctional Rack User Manual

Ultrasport Power Rack Fitness Rack Multifunctional Rack

Product Information

Specifications

• Brand: Ultrasport
• Website: www.ultrasport.net
• Language: English (GB)

FAQ

• Q: Where can I find replacement parts for the Ultrasport product?
• A: Replacement parts for Ultrasport products can be purchased directly from the official website or through authorized retailers.
• Q: How do I contact customer support for assistance?
• A: For customer support and assistance, please visit the Ultrasport website or contact the customer service hotline provided in the user manual.

Dear Sir, Madam
The manufacturer is constantly improving all types and models.
Please understand that changes to the delivered product in terms of form, features and technology are thus possible at any time.
Therefore no claims may be derived from the information, illustrations and descriptions in this manual. Reprint, duplication or translation, also of excerpts, is not permitted without the written permission of the manufacturer.
All rights according to the law or to copyright law are expressly reserved by the manufacturer.

PARTS LIST

SAFETY INSTRUCTIONS

IMPORTANT: THIS APPLIANCE IS INTENDED FOR HOME USE ONLY

1. Read all instructions in this manual before using the product. Keep this manual for the entire life of the product.
2. This device must be assembled by one or two adults.
3. The owner is responsible for ensuring that all users of this product are properly informed about its safe use.
4. This product is intended for home use only. Don’t use this product in a commercial, rental, or institutional environment.
5. The user is responsible for the proper care and maintenance of the device. After assembling the product, one must check that the fasteners are tightened and that no elements protrude and before each use. Regularly check the condition of the parts that are most susceptible to wear.
6. Don’t store this product in a damp place (e.g. at the edge of a pool, bathroom, etc.).
7. Wear sports shoes to protect your feet during exercise. Don’t wear loose clothing as this could get caught in the equipment. Jewellery should be removed.
8. Pin your hair together so that it doesn’t get in the way during your workout.
9. If you feel pain or dizzy during exercise, stop immediately, rest, and see a doctor.
10. Always keep children and pets away from the product.
11. Please consult your doctor before starting this training program, especially if you haven’t been active in sports for several years.
12. Don’t attempt to repair the device yourself.
13. The assembly/disassembly of the product must consider health safety.
14. Adhere to the specified user information and don’t exceed it.
15. Don’t bend your back and keep it straight during exercise.
16. Replace defective components immediately and keep the device out of operation until it is repaired.
17. Excessive or incorrect training can cause health problems.
18. The equipment must be properly aligned. Parents and other persons responsible for children should be aware of their responsibility since children’s natural playfulness and willingness to experiment can lead to situations and behaviours for which the training device isn’t intended.
19. lf children can use the device, one should take into account their mental and physical development and above all their temperament. They should be checked and instructed on the correct use of the device. Under no circumstances is the device suitable as a children’s toy.
20. Make sure that the seat is stable before using the device. If you feel pain, faint, dizziness or shortness of breath, stop your workout immediately. Stay on the device for a while until you feel better before getting up and leaving the device. Ask someone to help you to get off the device.
21. lf the adjusters stick out, your movement may be affected.
22. The free space on which the device is placed must be at least 60 cm larger than the device.

The device is NOT suitable for therapeutic purposes.

CARE AND MAINTENANCE

1. Wipe the surfaces dry after each training session. Do not use solvents – only clean with a damp cloth.
2. The user is responsible for the proper care and maintenance of the device. After the product has been assembled, check that the fasteners are tightened and that no elements protrude and before each use. Regularly check the condition of the parts that are most susceptible to wear.
3. Replace defective components immediately and keep the device out of operation until it is repaired.

TOOLS

To successfully assemble your product. you need a 2 x 14 mm and 2 x 17 mm wrench and a screwdriver. For an easier and faster a5$embly, a hammer with a soft head would be an advantage.

WEIGHT RESTRICTION

• Height-adjusts. stable mockers; Max. load weight 200 kg
• Pull-up bar; Max. user’s weight is 130 Kg
• Dip stand; Max. user weight 100 Kg
• Lat. and rowing: max. additional weight 80 Kg

Conformity
THIS PRODUCT MEETS:
EN ISO 20957-1:2013, EN 957-2:2003 and EN ISO 20957-4:2016 HOME USE-Class H

BEFORE YOU START
PREPARATION OF THE WORK AREA
You must assemble your product In a clean, clear and uncluttered place. In this way, you can move around tile products during the assembly of components and reduce the risk of Injury.

WORK WITH A FRIEND
It may make sense to assemble this product with the help of a friend, as some of the components are large, and differ, or awkward to use.

OPEN THE CARTON
Carefully open the box that contains your product and pay attention to the warnings on the outer box to reduce the risk of Injury. Look out for sharp brackets that can be used to see die flaps as they could injure you. Be sure to open the box the right way, as diis is die easiest and safest way to unpack all of the components.

UNPACK COMPONENTS
Unpack each component carefully and the parts 11th to check that you have all the die parts you need to complete the die assembly of your product.

ASSEMBLY INSTRUCTIONS

STEP 1

1. Secure the two leg press plates (17) to the lower connecting tube (3) with four carriage bolts, MS x 65 mm (43), four washers MS (49) and four nylon nuts MS (51 ).

2. Fasten the lower side tube (2) and the lower connecting tube (3) to the lower tube (1) with two hexagon bolts, M 10 x 70 mm (38), four washers M 10 (47) and two nylon nuts M10 (SO).

3. Secure the lower side tube (2) to the lower tube (1) with two hexagon head screws, M 10 x 65 mm (39), four washers M 10 (47) and two nylon nuts M 10 (SO).
   Note: The lower side tubes (2) can be mounted on any side of the lower tube (1 ). Which side they are attached to depends on how the gym is set up. This does not change the assembly process.

4. Fasten the lower tube (1) to the lower connecting tube (3) with two hexagon screws, M 10 x 65 mm (39), four washers M 10 (47) and two nylon nuts M 10 (50).

5. Secure the rear base frame (9) to the lower connecting tube (3) with two hexagon screws, M 10 x 65 mm (39), four washers M 10 (47) and two nylon nuts M 10 (50).

STEP 2

1. Secure the four pillars (4) to the two lower tubes (1) with eight hexagon bolts, M10 x 65 mm (39), sixteen washers M 10 (47) and eight nylon nuts M 10 (50).
2. Insert the two weight guide tubes (8) into the rear base frame (9) and fasten them there with two hexagon bolts, M 10 x 40 mm (41 ), four arched washers M 10 (48) and two nylon nuts M10 (50).
3. Slide the two springs (26) and two large washers (19) onto the weight guide tube (8).
4. Slide the weight plate frame (10) onto the weight guide tube (8).
5. Slide two spring clips (25) onto the weight plate frame (10).

STEP 3:

1. Push the support frame (14) onto the pillar (4) with two quick adjustment buttons (27). Attention! Make sure that the support frame (14) is on the same side of the lower side tube (2).
2. Push the long shelf (12) with two quick adjustment buttons (27) onto the column (4).
3. Push the four short shelves (13) onto a pillar (4) using a quick adjustment button (27).

STEP4:

1. Fasten the two upper connecting tubes (5) to the two pillars (4) with four hexagon screws, Ml Ox 65 mm (39), eight washers M10 (47) and four nylon nuts M10 (SO).
2. Fasten the two upper connecting tubes (5) and the upper rear connecting tube (6) to the two pillars (4) with four hexagon screws, M 10 x 70 mm (38), eight washers Ml 0 (47) and four nylon nuts M10 (SO).
3. Attach the upper front connecting tube (11) to the two upper connecting tubes (5) with four hexagon screws, M 10 x 65 mm (39), eight washers M 10 (47) and four nylon nuts M 10 (SO).
4. Remove two M10 x 20 mm hexagon bolts (42) and two M10 washers (47) from the weight guide tube (8).
5. Fasten the upper cross member (7) to the weight guide tube (8) with two hexagon screws, M 10 x 20 mm (42) and two washers M 10 (47).
6. Secure the upper cross member (7) to the upper rear tube (6) with two hexagon head screws, Ml Ox 65 mm (39), four washers Ml O (47) and two nylon nuts Ml O (SO).

STEP 5:

• Start with the upper rope (20).
• Insert the upper rope (20) into the groove of the pulley (22TI (29) and then thread the upper rope (20) through the upper cross member (7).
• Fasten Pulley 1 (29) and two plastic sleeves (30) to the upper cross member with a hexagon screw (7), M10 x 70 mm (38), two washers M10 (47) and a nylon nut M10 (SO).
• Fasten Pulley 2 (29) and two plastic sleeves (30) to the upper cross member with a hexagon screw (7), M10 x 70 mm (38), two washers M10 (47) and a nylon nut M10 (SO).
• Fasten Pulley 4 (29) to the upper cross member (7) with a hexagon screw, M10 x 45 mm (41 ), two washers M 10 (47) and a nylon nut M 10 (SO).
• Attach the end of the rope (20) to the weight plate frame (10).
• Fasten Pulley 3 (28) and two pulley suspensions (34) to the pulley-U (18) with a hexagon screw, M10 x48 mm (40), two washers M10 (47) and a nylon nut M10 (SO).
• Attach the lat pull bar (15) to the other end of the upper rope (20) with a carabiner (22).
• Assembly of the lower rope (21).
• Insert the lower rope (21) into the groove of the pulley (27TI (28) and thread it through the rear base frame (9).
• Fasten Pulley 5 (28) and a pulley suspension (34) to the lower base frame (9) with a hexagon screw, M10 x48 mm (40), two washers M10 (47) and a nylon nut M10 (SO).
• Fasten the Pulley 6 (28) and two pulley suspensions (34) to the pulley-U (18) with a hexagon screw, M10 x48 mm (40), two washers M10 (47) and a nylon nut M10 (SO).
• Attach the end of the rope (21) with a hexagon screw, M 8 x 40 mm (44), two washers MB (49) and a nylon nut MB (51), a short chain (24) and a carabiner (22) on the lower base frame (9).
• Attach the lower bar (16) to the other end of the rope (21) with two carabiners (22) and a long chain (23).

Note:
After finishing the assembly, there are four unused holes in the lower tube (1) on the lower left. With their help, the power rack can be anchored to the floor if necessary.

How to set the weight rest
Loosen and pull out the quick button (27), set the desired height and tighten it. Note:
Please note when setting whether there are any obstacles around the product.

Add the weight plate
This device is suitable for weight plates with a hole size of 26,5 mm. The maximum outside diameter is R 350. The most effective width of the weight plate tube is 180 mm per side. The maximum weight per side is 40 kg, for a total of 80 kg.

FITNESSGUIDE

EXPLODED VIEW

Technical Specifications

• Model: 331100000352/331100000355
• Dimensions (WxDxH): ca.1400x 1500×2150 mm
• Weight: 75kg max. user weight
• Height-adjustable mockers; max. load weight: 200 Kg
• Pull-up bar; Max. user weight: 130 Kg
• Dip stand; Max. user weight: 100 Kg
• Lat. and rowing: max. additional weight: 80 Kg

The device is NOT suitable for therapeutic purposes.

Disposal
Dispose of the packaging

Dispose of the packaging according to the type. Add paperboard and cardboard to the waste paper and foils in the recycling collection.

Warranty

Warranty Card

• If you wish to claim the guarantee,
• please contact our service hotline or send us an email first.
• Manufacturer & Service
• Summary GmbH, Vossbarg 1, 25524 Itzehoe, Germany
• Toll-free customer service number: 00800 880 880 08 (international free call) Email: service.uk@ultrasport.net.
• http://www.Facebook.com/Ultrasport.net.

© Alle Rechte vorbehalten/All rights reserved/Tous droits réservés/Tutti i diritti riservati/Reservados todos los derechos

References

• ULTRASPORT – Nr. 1 Marke für Sport und Fitness bei Amazon – Sport & Freizeitartikel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>