home zone security ELI1621G Solar Path Light Installation Guide

home zone security ELI1621G Solar Path Light

Specifications

• Model Number: ELI1621G
• Dimension: approx. 6.30D x 14.37H
• Light source: 4pcs LEDs per light
• Brightness: Standby: 10 lumens; up to 300 lumens when activated
• Sensor range : 110 degree / 16ft
• Wireless transmit distance: up to 164 feet (50m)

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU MAY NEED THEM AT A LATER DATE.

WARNING: IMPORTANT SAFETY OPERATING INSTRUCTIONS

1. Please read all warning and instruction labels that are included in the box and fixture to avoid personal injury, property damage caused by fire, cuts, bruises, death and other dangers
2. Please follow these general precautions before installing, maintaining, or fixing

WARNING

1. The packing contains small parts that could be swallowed by children
2. Keep the packaging material away from children and pets
3. The solar light is not a toy
4. We do not take responsibility if the instruction manual is not followed correctly or if the product is handled improperly resulting in damage to person or property

PRECAUTION

1. It is important to select an outdoor location with full, direct sunlight where the solar panel can receive at least 6 hours of sunlight each day.
2. It is important to avoid placing the solar light by light sources, such as street lights or porch lights, which may cause the solar light to turn off automatically.
3. To avoid explosion and corrosion, please keep the solar light away from fire and humid environment
4. No striking to avoid any damage to solar cell

REF. PARTS

PARAMETER

1. Dimension: approx. 6.30″D x 14.37″H
2. Light source : 4pcs LEDs per light
3. Brightness: Standby: 10lumens; up to 300lumnes when activated
4. Sensor range : 110 degree / 16ft
5. Wireless transmit distance: up to 164feet (50m)

HOW TO OPERATE AND INSTALL (Ref Figure 1 & Figure 2)

• Twist the Solar Panel Unit (Part A) from the Lens (Part B)
• Slide the power switch to your desired channel (CH1/CH2/CH3/CH4). Slide the CCT switch to your desired color temperature (3000K/4000K/5000K) on the bottom of the Solar Unit (Part A), reassembling the Solar Panel Unit and The Lens.
• Insert the Ground Spike (Part D) to the Tube (Part C).
• Insert the assembled Ground Spike (Part C & D) into the ground where it can receive a full 8 hours of sunlight to allow the rechargeable battery to reach maximum capacity.
• Put the assembled Solar Panel Unit (Part A & Part B) into the Tube (Part C & D) Note: Lights with solar panels may have a protective film over the solar panel. This must be removed before use.
• Then the light will light on automatically at dusk

HOW IT WORKS

CLEANING AND MAINTENANCE

1. Use a damp cloth to clean the solar panel
2. To avoid any damage to this light, please do not use any chemical or abrasive cleaner

**RECHARGEABLE BATTERY

**

This product contains (1)3.2V 14550 600mAH LiFePO4 rechargeable battery. When the battery expires, it must be recycled or disposed of properly. Please contact your local waste disposal authority for correct procedure. Do not put battery into fire.

• Only rechargeable batteries are to be used.
• Exhausted batteries must be removed from the product.
• Batteries must be placed at the correct polarity.

Battery replacement

• Twist the Solar Panel Unit (Part A) from the Lens (Part B)
• Remove the battery compartment cover
• Take out the old battery from the battery compartment
• Replace with a new battery, making sure the polarity is correct.
• Put the battery cover back

FAQ

Frequently Asked Questions

• Q: What should I do if my solar lights are not turning on?
  • A: Ensure that the solar panel is placed in direct sunlight for adequate charging. Check the battery and connections for any issues.
• Q: How long does the battery last on a full charge?
  • A: The battery life may vary based on usage, but typically it can last through the night on a full charge.

FCC

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.

Model Number: ELI1621G
INSTALLATION INSTRUCTIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>