LA VAGUE LV-HD340 LED Projector Instruction Manual

LA VAGUE LV-HD340 LED Projector

PLEASE NOTE

1. Please read the entire user manual carefully before using the projector.
2. To ensure the stability of the power supply, use standard grounded power sockets.
3. Only use a power source as indicated on the projector.
4. Please do not open projector. There are no user-serviceable parts in the projector. Opening the projector will void warranty. If there is a problem with your projector contact your supplier.
5. Please do not directly look into the projector lens. The bright light could damage your eyes.
6. Please do not place projector on a surface that may block air flow from the vents. A soft fabric could prevent air flow. Place the projector on stable hard surface.
7. Please keep projector away from any liquids. The projector is not water proof or water resistant and is not for use outside.
8. To prevent electrical shock please keep projector away from moisture.
9. Please turn off and unplug projector when not in use.
10. Please use original packaging material when storing your projector.

PRODUCT OVERVIEW

1. Status LED
2. On / Off button
3. Navigation
4. Select input
5. Back in the menu
6. Call up the menu
7. Objective Focus
8. Keystone correction

INTERFACES

1. 3,5mm audio output
2. 3.5mm audio/ video input
3. HDMI input
4. VGA input
5. SD card input
6. Infrared input
7. HDMI input
8. USB input

REMOTE CONTROL

INITIAL STEPS

• Connecting the power cable
  Connect the power cable to the side of the projector and to a power outlet. If the indicator light at the top of the projector turns red, the projector is in standby mode.

• Power up

  • Remove the lens cap from the lens.
  • Press the „Power“ button on the top of the projector or the „Power“ button on the remote control. If the indicator light on the top of the projector is steady green, the projector is turned on.
  • Press the „Power“ button again either on the projector or on the remote control to turn off the projector.

• Keystone correction/image focusing
  Use the rear keystone adjustment dial (7) located at the top of the projector to adjust the angle of the projector. Use the front keystone adjustment dial (8), also located on the top of the projector, to adjust the image focus.

• Selecting the signal source

  • Press the „S“ button on the projector or the „Source“ button on the remote control to open the menu for selecting the input signal.
  • Use the arrow buttons on the remote control or on the projector to select the appropriate signal source and confirm with „OK“.

• Multimedia connection
  Insert a SD card or a USB device into the appropriate input. Select the USB/SD media source, then select the desired media (Photo/Movie/Music/File). Select the file(s) you want to view, and then press the Play/Pause button on the remote control.
  The following formats are supported for „USB“ and „TF Card“ sources: File| Format| File extension| Codec
  ---|---|---|---
   | JPEG| .jpg|
  Picture| BMP| .bmp|
   | PNG| .png|
   | WMA| .wma|
  Music| MP3| .mp3|
   | AC3/WAV| .ac3 / .wav|
   | RM/RMVB| .rm / .rmvb| RV8 / 9 / 10
   | AVI| .avi|
   | ASF| .wmv / .asf|
   | MP4| .mp4 / .mov / .3gp|
  Movie| H264| .mov| MPEG 1,2,4
   | MKV| .mkv|
   | FLV| .flv| H.364
   | PS| .mpg/.mpeg/.vro/.vob| vc1
   | TS| .ts| H.264

• HDMI Equipment Connection
  Connect a computer and other HDMI devices to the corresponding input located at the side of the projector. Select the media source „HDMI“, and press „OK“.

• VGA Equipment Connection
  Connect a computer and other VGA devices to the corresponding input located at the side of the projector. Select the media source „VGA“, and press „OK“.

• AV Video connection
  Connect the included 3-in-1 video cable to the corresponding input located at the side of the projector to connect the AV equipment. Then press „OK“ and select the media source „AV“.

• Audio Equipment Connection
  Connect a 3.5mm earphone or other supported sound equipments into the corresponding output located at the side of the projector.

MENUS

MULTI-SCREEN

This allows the screen content of a smartphone or tablet to be displayed wirelessly or via a USB cable on the projector.
Please note that not all content can be displayed due to copy protection requirements of the respective app provider (e.g. Netflix). By using the Amazon Firestick or Google Chromecast, you can also stream content from these providers.

• Basic settings for multi-screen-sharing
  To enter multi-screen-interface select „Wifi Display“ on the main menu and press „OK“.

• **Multi-screen for Android phones

**

  *  **Step 1:** From the WiFi Display menu, select Miracast.

  *  **Step 2** : Go to the Miracast / Wireless Display / Multiscreen function on your smartphone and connect to the projector via the SSID.

• **Multi-screen for iPhones

**

  *  **Step 1:** Open the settings menu in your phone, turn on WiFi, and connect to your wireless network.
  *  **Step 2** : Connect the projector to the same WLAN by selecting the symbol in the „Setting“ area and register the projector in the WLAN as follows:

  *  **Step 3:** Enter „Wifi Display“ from the main menu, select „iOS Airplay“ and press „OK“ to enter iOS wireless connection interface.

  *  **Step 4:** Confirm Air-Play Mirroring by selecting the SSID on the IOS device.

• Connection via cable connection (Android)
  Please check if your Android device supports image transfer via USB cable.

  • Step 1: From the WiFi Display menu, select Cablecast.

  *  **Step 2:**
  * Connect your Android smartphone to the right USB port (not the OUT-5V USB port) using the original USB cable supplied by the phone manufacturer. Then open the settings on your Android smartphone and enable „USB debugging“ in the developer options.
  * If you do not find the menu item „Developer options“ in your settings, it must be activated first. Please search the Internet for the necessary steps to do this.

• Connection via a cable connection (iOS)
  • Step 1: From the WiFi Display menu, select Cablecast.

  *  **Step 2:** Confirm the connection with „Trust“. Use only original Apple USB cable.
  *  **Step 3:** Click on „Allow“ to start sharing multiple screens.

SPECIFICATIONS

DISPOSAL

This symbol indicates that this product is subject to the European Directive and must not be disposed of together with other household waste. Refer to and follow local regulations for separate collection of electrical and electronic equipment. Proper disposal of old products helps to avoid negative effects on the environment and health.

MANUFACTURER

• VEHNSGROUP GmbH
• Theatinerstraße 40-42
• 80333 Munich
• Germany
• www.vehnsgroup.com
• service@vehnsgroup.com
• MADE IN CHINA
• Changes and errors excepted.
• The manufacturer accepts no liability for damage resulting from incorrect, improper or incompatible use of the product.
• © VEHNS GROUP GmbH

References

• LA VAGUE
• VEHNS GROUP Website – Unternehmensprofil der VEHNS GROUP

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>