KOTION EACH M9 True Wireless Headset Instruction Manual
- June 15, 2024
- KOTION EACH
Table of Contents
**KOTION EACH M9 True Wireless Headset Instruction Manual
**
Packing list
-
Headset X2
-
Charging CaseX1
-
Instructions X1
-
Type-C Charging CableX1
Product Diagram
Tips
- Except for the operation methods specifically marked in the manual, please do not try to disassemble or replace any parts in the earbuds.
- Don’t put the earbuds in the water or any others liquid. The earbuds are not waterproof.
- If any liquid enters the product by accidentally, please disconnect and remove the connection immediately.
- Please make sure that there is no water on your hands when Installing or uninstalling the product to avoid electricshock.
- Do not put the product near by the heat source or expose it to the fire source directly.
- Do not put the product in the environment with strong electromagnetic force, otherwise it will cause product malfunction.
Product specifications
Wireless version: V5.3
Music time: 5hours(60% volume)
Charging time: ≈1.5hours
Rated input: 5V – 30mA
Transmission distance: 10M
Horn size: $13mm
Battery capacity: 35mAh
Charging case specifications
Battery capacity: 300mAh
Rated input: 5V === 250mA
Charging time: 1-2 hours
(All technical information is subject to actual performance)
(tip: When the headset is in low power (3.2+/-0.1v), there will be a
“Please charge” prompt tone every minute until the headset is powered off)
Rated input: 5V-30mA (headset)
Rated input: 5V 250mA (charging case)
LED Indicator Status
Power On: Power Off
Successful pairing: Flash the white light
Flash the light twice: The main headphone light is blinking, and the
secondary headphone light is off
Successful connection: Headphone light goes out
Empty pair: The light flashed twice and then went out
Earphone charging: After the headphone is in the warehouse, the headphone
lamp will turn on and start charging. The charging bay indicator lights on for
5 seconds and then turns off. After the headset is fully charged, the headset
indicator is off.
Charging bin: Charging bay indicator flashing, full of steady on
Product Operation Instructions
-
Turn on
Method 1: Take out the earphone from the charging bin, and the earphone will start automatically
Method 2: The earphone is outside the charging bay and in the off state. Long press the touch position for 3 seconds, and the earphone will have a”power on” prompt tone at the same time -
Turn off
Method 1: In the startup state, put the earphone into the charging box, and the earphone will automatically shut down and enter the charging mode
Method 2: Hold down the touch button for 5 seconds, and the earphone will hear the “Power Off” tone
Method 3: When the earphone battery runs out, the earphone has a “power off” prompt tone, and the earphone shuts down itself
Method 4: If no operation is performed after connection or connection is successful, the headset automatically shuts down 5 minutes after timeout -
Pairing and connection Enter the pairing state: After the device is powered on, the left and right earphones are close to each other, and the left and right earphones are automatically connected. When the connection is successful, the earphones will sound “Didi”. Earphone connection: After the two earphones are paired, search “M9” on the mobile phone and click “Connect” to use the earphone. When the connection is successful, the earphone will sound “connection success”.
Connection succeeded: Voice prompt: “connected”
Connect back: After the headset is powered on, the system automatically
searches for the last Wireless device to connect back
Touch operation
-
General mode
Volume Plus: Hit the left Touch three times
Volume reduction: Strike three on the right Touch -
Music playback mode
Play/Pause: Click any Touch key
Previous: Double click on the left Touch button
Next: Double click on the right Touch button -
**Call mode
Answer an incoming call: Short press any Touch key to answer an incoming
call
Hang up: During a call, press any Touch key to end the call
Reject a call: Hold down the Touch button for 1 second for an incoming
call’
**
The name and content of harmful substances in the earbuds
| Part Names | Harmful Substances |
|---|---|
| Pb | Hg |
| Printed circuit assembly | 0 |
| Small structural ports such as shell | 0 |
This form is compiled in accordance with &Ill–11364.0:Indicates that the
content of the hazardous substance ‘n allhomogeneous materials of the part is
in below the limit required byGB/T 26572.X:Indicates that the hazardous
substance at least in a certain homogeneous material of the port exceeds The
limit requirements specified in GB/T 26572.The ports marked with “X” on the
form are all harmful due to the limitations of global technological
development. Substitution of substances.
Printed circuit board components: Including printed circuit boards and their
ports, electronic components, etc. ond depending on the product model, the
earbuds you purchased may not contain all the above components.
Ellis Electronic and electrical products sold in the10 number in the logo represents the product under normalsofPeople’ s Republic of China must mark this LOGO, the use Environmental protection use period.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>