Lucci decor 180076 Dawn II 35W Colour Switching Flush Mount Instruction Manual

: June 4, 2024
: Lucci decor

Table of Contents

180076 Dawn II 35W Colour Switching Flush Mount
Warranty
Installation requirements
Installation directions
Safety Tips
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

180076 Dawn II 35W Colour Switching Flush Mount
Instruction Manual

180076 Dawn II 35W Colour Switching Flush Mount

Installation Instructions
LEDOUX DAWN II LED BATTEN SKU# 180076,180077,180078,180079
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of the product. Please keep the instructions for future reference.

Warranty

This product is covered by a 3-year warranty. Please retain the proof of purchase.
The warranty will be void if there is any damage due to improper usage or modification to the product.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
This luminaire is not suitable for use with dimmer switches. The warranty will be void if the luminaire is used on the same circuit which has a dimmer switch.

Installation requirements

Must be installed by a licensed electrician.
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
E.g. AS/NZS 3000 Electrical installations.
This is a Class I luminaire and must be earthed during installation.
Select a suitable location for installation:
– This luminaire is suitable for indoor use only.
– The mounting point must support 2 times the weight of the luminaire.
– Ensure the luminaire is not installed in direct line of an air vent/system
– If installing a luminaire in an area prone to moisture, ensure that the area is well-ventilated, and appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
Ensure power to the circuit you are working on has been switched OFF, before commencing any electrical work.

Installation directions

Remove all packaging material from the luminaire and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

Loose the four screws from the end covers. Remove the insulation plugs before accessing to the screws. (Fig.1)
Remove the end covers from both sides. (Fig.2)
Adjust the color temperature (3000K – 4000K – 5000K) according to your need. (Fig.3)
NOTE: There are four spacers provided if the wires of the main suppliers are required to run through the center. Install the spacers first before proceeding to the next step.
Use the luminaire as a template, and mark the screw positions on the desired surface. And then drill the holes into the desired surface. (Fig.4)
Install the luminaire onto the desired surface using appropriately sized mounting screws. Ensure the screws used are suitable for the mounting surface.
Connect the main supply wire to the terminal block as follows: (Fig.5)Mains Supply Wire
Earth-Yellow/Green
Neutral- Blue or Black
Live- Brown or Red| Luminaire Wire
Yellow/Green
Blue
Brown
---|---

Ensure wires are secure, and no bare wires are exposed.

Install the end covers back to the luminaire. (Fig.6)
Secure the end covers by tightening the four screws. (Fig.7)
NOTE: Ensure the insulation plug is installed back to the screw holes.
After the installation, switch on the luminaire to test all the lighting functions and enjoy your new luminaire.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire shall be replaced.
Select a suitable location away from liquids and hazards.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.