SDJ WECONBOX Wireless LED Status Transceivers User Manual

SDJ WECONBOX Wireless LED Status Transceivers

INTRODUCTION

Thank You for choosing one of Our products!
Please refer to the instructions and warnings contained in this user manual, please retain it for future reference.
This manual contains information about the installation and use of the device. The information contained in this publication has been carefully prepared and checked. However it is not assumed any responsibility for any inaccuracies. All rights are reserved and this document can not be copied, photocopied, reproduced in whole or in part without previous written permission of PROEL. PROEL reserves the right to make, without notice, any aesthetical, functional or design changes or modifications in everyone of its products. PROEL doesn’t assume any responsibility for the use or application of the products here described.

The crossed bin symbol, shown on the product or on accompanying documents, indicates that the product should not be disposed with other household waste at the end of the lifecycle. To avoid any damage to the environment, the user is encouraged to separate this product from other kinds of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Home users are encouraged to contact the retailer where they purchased this product or their local government office for details on separate collection and recycling this type of product. Business users are encouraged to contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste.

The lightning symbol with arrow in an equilateral triangle intends to alert the user to the presence of not insulated “dangerous voltages” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point symbol within an equilateral triangle intends to alert the user to the presence of important instructions for use and maintenance on the accompanying documents of the product.

The “F” inside an equilateral reversed triangle means that the product is suitable for mounting on normally flammable surfaces.

The product to which this manual refers comply with the European Directives pursuant to the safety of electrical equipment supplied at low voltage (LVD) and to the Electromagnetic Compatibility (EMC)

SAFETY INSTRUCTIONS

Caution! This product is not suitable for household use.
Please read this manual before installing and applying power to the equipment, follow the safety precautions listed below and observe all warnings in this manual and printed on. Please contact a PROEL distributor for assistance with any questions about how to activate the equipment safely. Contact a qualified technician for any maintenance work not described in this manual.
Do not modify the fixture or install accessories and upgrade kits that are not the Proel original ones.

People involved in the installation and maintenance of the device must:

• Be qualified
• Follow the instructions of this manual in the theaters, in the halls, in the places where the events take place, etc.

CHECKS BEFORE INSTALLATION

Make sure all the parts for fixing the product are in good condition. Make sure that the anchor point is stable before positioning the product. The safety cable must be properly attached to the device and fixed to the supporting structure so that, in case of failure of the primary supporting system, it has the lowest possible fall of the device.
If the safety cable wear, must be replaced with an original spare.

MINIMUM DISTANCE FROM FLAMMABLE MATERIALS

The product must be positioned so that any flammable material is at least 0.50 meters from any point of the surface of the device.

MOUNTING SURFACES

The device is suitable for mounting on normally flammable surfaces.

REFERENCE TEMPERATURE

The ambient temperature range of use of the device varies between + 5 ° C (min) and + 40 ° C (max), outside of that range the device should not be used.
The maximum temperature of the housing Tb = 80 ° C must never be exceeded. Do not block the exhaust fans, ensuring a minimum clearance of 0.5 meters around the ventilation holes.

IP20 PROTECTION RATING

The device is protected against the penetration of solid bodies larger than 12 mm (0,47 “) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0). Use only in dry areas. Inside use only. Do not expose the equipment to rain or moisture.

PROTECTION AGAIN ELECTRIC SHOCK

The device must be connected to a power supply system with efficient earthing. Moreover, it is recommended to protect power supply lines of the product from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch.

CONNECTION TO THE MAINS

The electrical connection must be carried out by a qualified electrician.
Ensure that the mains frequency and voltage correspond to those for which the equipment is designed, as shown in the electrical data label. This label also shows the power consumption that is necessary to refer to evaluate the maximum number of devices to be connected to the electricity line, in order to avoid power overloading.
If the external power cord of this light is damaged, it must be replaced with a special cord exclusively available from Your PROEL dealer.
Never operate the equipment with lenses and / or covers missing or damaged. In case of non-use, it is recommended to unplug the projector from the mains.

MAINTENANCE

Before starting any maintenance or cleaning the product, disconnect the power from the mains and disconnect the power cable from the device. After switching off, do not remove any part of the device for at least 35 minutes to avoid the risk of burns. The parts, if damaged, must be replaced with original spare parts.

OPENING AND CONTROL

Carefully open the package, check the content and make sure that all the parts are present and are in good condition. In cases where some parts are not present or are damaged, immediately contact Your supplier and retain the packaging for verification.

WARNING!
If the product has been exposed to drastic temperature changes, let the unit turned off until it reaches room temperature because the presence of condensation can damage the product if it is turned on.

Verify that the box contains the following items:
N° 1 SG WECONBOX
N° 1 Adapter 5VDC
N° 1 Supply cord

INSTALLATION AND SWITCH ON

PRODUCT INSTALLATION

• Do not shake the device. Avoid the use of too much force during installation or unit fixing.
• The unit can be installed on the floor, on the wall, ceiling or on a truss.
  

WARNING! IT’S REQUIRED
the mounting of the safety rope (PLH232 – PLH248 sold separately) in the case where the product is hung on a wall, ceiling or on a truss. Except when the device is placed in the floor, the safety cable is always required.

CONNECTION TO THE MAINS

The device must be connected to a power supply system with a proper earth system. Moreover, it is recommended to protect power supply lines of the products from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch. The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the device is designed, as shown in the electrical data label.

CONNECTION TO THE DMX CHAIN

Use a cable conforming to specifications EIA RS-485: pole twisted, shielded, 120Ohm characteristic impedance and low capacity (SAGITTER SG DMX3 – SG DMX5). Do not use microphone cable or other cable with different characteristics than those specified. Terminations must be made with male / female XLR 3-pin connectors. You must enter on the last device a terminal plug with a 120Ohm resistance (min 1/4 W) between terminals 2 and 3. IMPORTANT: The cables must not come into contact with each other or with the metal housing of the connectors. The housing itself must be connected to the shield braid and to pin 1 of the connectors.

The transceiver SG WECONBOX has 2 operative modes.
Setup mode and Working Mode. To switch from one operating mode to another, the device must not be connected to the DMX line.

USE

The transceiver SG WECONBOX leaves our warehouse already set as default in Transmitter Protocol 1: LED status (2) blue. If this is the desired Working Mode, it is possible to directly go to the section 5.2, specific section 5.2.3.

SETUP MODE

Setup mode is used in order to set the operative protocol. To enter in Setup mode:

• When the device is OFF, press and hold the multifunction button (3).
• Switch ON the device
• When the status LED (2) will turn white, release the multifunction button (3).

In this status, by pressing again and repeatedly the multifunction button (3) it will be possible to choose between 5 different operative protocols related to different colors of the status LED (2):

• RED: WECON protocol 6 groups
• GREEN: Receiver protocol
• BLUE: Transmitter protocol 1
• YELLOW: Receiver / Transmitter 7 groups protocol
• MAGENTA: Transmitter protocol 2

After selected the protocol to use, press and hold the multifunction button (3). After that the status LED (2) will have a little flash with different colors, release the multifunction touch button (3), the device will enter in Working mode and the the status LED will assume one of the colors described in the following sections.

WORKING MODE

WECON PROTOCOL 6 GROUPS (SETUP mode Red)

In this mode, the status LED (2) will assume 6 different colors corresponding to different transmitter / receiver modes depending on the color of the group. The color of the group will be chosen by repeatedly pressing the multifunction button (3).

STATO E COLORE

Group 1 Red
Group 2 Green
Group 3 Blue
Group 4 yellow
Group 5 Cyan
Group 6 Magenta

Switching between transmitter / receiver mode will take place automatically depending on whether a DMX console unit is connected to the device (transmitter), or whether a projector is connected (receiver).

RECEIVER PROTOCOL (SETUP mode: Green)

In this condition, the status LED (2) will assume different colors corresponding to different working modes as indicated in the table below:

transmitter is OFF
Green slowly blink| The receiver is linked to a transmitter, the transmitter is ON, but not connected to a DMX signal
Green fixed| The receiver is linked to a transmitter, the transmitter is ON, and connected to a DMX signal
Green quickly blink| The receiver is linking to a transmitter. This phase lasts only a few seconds, then the LED will assume a status as described above.

In order to unlink the receiver from the transmitter it is possible to follow 2 different ways:

• Do the massive unlink from the transmitter (see the section related to the Transmitter protocol operating mode)
• Do the single unlink in the receiver, by pressing and hold the multifunction button (3), until the status LED (2) will have a little blue flash. Then release the multifunction button (3) and the status LED (2) will come white again.

TRANSMITTER PROTOCOL 1 (SETUP mode Blue – DEFAULT SETTING)
TRANSMITTER PROTOCOL 2 (SETUP mode Magenta)

In this condition, the status LED (2) will assume different colors corresponding to different working modes as indicated in the table below:

In order to link the receivers, press and hold the multifunction button (3). In this situation the LED status (2) will quickly blink in blue color for few seconds until the link is finished.
In order to unlink all the receivers at once (massive unlink), press and hold the multifunction button (3). When the status LED (2) will start to quickly flash in blue color, release the multifunction button (3). The status LED (2) will be RED for few seconds until the unlink is finished. After the status LED (2) will come in one of the status indicated in the table before.

RECEIVER TRANSMITTER 7 GROUPS PROTOCOL (SETUP mode Yellow)

In this mode, the status LED (2) will assume 7 different colors corresponding to different transmitter / receiver modes depending on the color of the group. The color of the group will be chosen by repeatedly pressing the multifunction button (3).

STATUS AND COLOR

Group 1 Red
Group 2 Green
Group 3 Yellow
Group 4 Blue
Group 5 Magenta
Group 6 Cyan
Group 7 White

Switching between transmitter / receiver mode will take place automatically depending on whether a DMX console unit is connected to the device (transmitter), or whether a projector is connected (receiver).

MAINTENANCE

To ensure optimal performance, the unit must be frequently cleaned. Unplug the device from the mains and let it cool for at least 35 minutes to avoid the risk of burns. Use a vacuum cleaner or an air compressor or a soft brush or a cloth to remove the dust deposited.

TECHNICAL SPECIFICATIONS

• Power Supply: 5VDC – 1A
• Dimensions (L x H x D): mm. 150x97x75
• Weight: kg 0,23
  

CUSTOMER SUPPORT

SDJ is a brand of PROEL SPA (Worldwide Headquarters) Via alla Ruenia, 37/43 64027 Sant’Omero (TE) – ITALY
Tel. +390861 81241
Fax +39 0861 887862
P.I. 00778590679
N. Reg. AEE IT 08020000002762
sagitter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>