Shenghuama Technology D30 Lshb Bell Instruction Manual
- May 15, 2024
- Shenghuama Technology
Table of Contents
Shenghuama Technology D30 Lshb Bell
Note:
- Please ensure the battery is fully charged before first-time use.
- Our doorbells are ready to use out of the box. If you purchase multiple doorbells at the same time and want them to be used together, you need to pair the doorbells.
Operating Instruction
- Press the transmitter call button to make the request.
- Press the receiver answer button to speak when the bell rings.
- Press the receiver answer button again to finish the call.
Installation Method
Function Instruction
Transmitter
- Press the call button to make the request.
Receiver Answer
- Press the answer button to speak when the bell rings.
- Press the answer button to finish the Asasas call.
Receiver Volume & Chimes
- Adjust the ringtone volume with V+ and V- When the bell rings.
- Adjust the voice volume with V+ and V- when speaking.
- Long press V – to select chime from 4 ringtones easily.
Receiver LED Indicator
- The blue LED light blinks once every 5 seconds in standby mode.
- The blue LED light stays continuously on in working.
Low Battery Reminder
- Please ensure the battery is fully charged before use.
- Replace the transmitter’s battery when the receiver prompts ‘Outdoor battery low’.
- A new battery could last approximately 3 to 4 months.
Product Features
Pairing Instruction
Our doorbells are ready to use out of the box. If you purchase multiple doorbells at the same time and want them to be used together, you need to pair the doorbells.
Add new receiver
- Plug the new receiver into the socket, then press the V+ and V- button simultaneously until you hear the ‘Searching’ sound.
- Press the button on the existing transmitter until you hear the ‘Successful’ sound.
Add new transmitter
- Press the V+ and V- buttons on the existing receiver simultaneously until you hear the ‘Searching’ sound.
- Press the button on the new transmitter until you hear the ‘Successful’ sound.
Pairing Notes
If the device cannot be used normally after pairing, you need to clear the code to reset the device, and then pair again to use it normally.
Note
Normally, you don’t need to do this. It may cause all doorbells to be
unusable.
Clear receiver’s code
Plug the receiver into the socket, then simultaneously press the smile button
and the V+ button until you hear the ‘Di’ sound.
Clear transmitter’s code
Press the button, the LED light will light up, and then press it continuously for 6 times. you will hear the ‘Di’ sound.
Brand & Service
Welcome to LSHB•BELL LSHB BELL not only provides high-quality doorbell products but is also dedicated to ensuring your satisfaction throughout your usage. At LSHB BELL, Your satisfaction is our driving force. For inquiries, feel free to contact us through our Amazon store platform: Amazon – Order list — Choose the order — Get help with the order.
Product List
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.