IKEA AA-2412050-2-1 LAGAN Integrated Dishwasher Instructions

IKEA AA-2412050-2-1 LAGAN Integrated Dishwasher

Specifications

• Brand: LAGAN
• Product Type: Dishwasher
• Model: Not specified

Product Description

1. Upper rack
2. Foldable aps
3. Upper rack height adjuster 4 Upper sprayer arm
4. Lower rack
5. Cutlery basket
6. Lower sprayer arm
7. Filter Assembly
8. Salt reservoir
9. Detergent and Rinse Aid dispensers 11 Control panel

First Use

Advice regarding the first-time use
Before installation and first usage of the appliance please read carefully „ SAFETY INSTRUCTION” and „ASSEMBLY INSTRUCTION” available in the product literature bag. Please remember to remove all transport protection parts from the dishwasher.

Filling the salt reservoir
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.

• THE SALT RESERVOIR must BE NEVER EMPTY.
• It is important to set the water hardness.
  The salt reservoir is located in the lower part of the dishwasher (see PRODUCT DESCRIPTION) and should be lit when the SALT REFILL indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. Position the funnel (see figure) and fill the salt reservoir right up to its edge (approximately 1 kg); it is not unusual for a little water to leak out.
3. Only the first time you do this: fill the salt reservoir with water.
4. Remove the funnel and wipe any  salt residue away from the opening

Make sure the cap is screwed on tightly so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair).
As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers. If the salt container is not called, the water softener and the heating element may be damaged
as a result of limescale accumulation. Using Salt is recommended with any type of dishwasher detergent. Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.

Setting the water hardness
To allow the water softener to work perfectly, it is essential that the water hardness setting is based on the actual water hardness in your house. This information can be obtained from your local water supplier. The factory sets the default value for the water hardness.

• Switch on the appliance by pressing the ON/OFF button.
• Switch the appliance by pressing the ON/OFF button.
• Hold down the button for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing quickly the ON/OFF button.
• The program indicator light of the current set level flashes.
• Press the button to select the desired hardness level (see WATER HARDNESS TABLE).
• Switch the appliance by pressing the ON/OFF button. The setting is complete!

Water Softening System
Water softener automatically reduces water hardness, consequently preventing scale buildup on the heater, contributing also to better cleaning efficiency. This system regenerates itself with salt, therefore it is required to refill salt containers when empty.

• The frequency of regeneration depends on the water hardness level setting – regeneration takes place once per 6 Eco cycles with the water hardness level set to 3.
• The regeneration process starts in the final rinse and finishes in the drying phase before the cycle ends.

Single regeneration consumes: ~3.5 L of water;

• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005 kWh of energy.

Filling the rinse aid dispenser
Rinse aid makes dish DRYING easier. The rinse aid dispenser LA  should be filled when the dark optical indicator on the dispenser door c becomes transparent.

1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference notch of the filling space – avoid spilling it. If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it. NEVER pour the rinse aid directly into the tub.

Adjusting the dosage of rinse aid
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press the button three times – a beep will be heard.
• Switch it on using the ON/OFF button.
• The program indicator light of the current set level flashes.
• Press the button to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button.

Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The LOW RINSE AID indicator light will not be lit if you run out of rinse aid. A maximum of 5 levels can be set according to the dishwasher model. The factory setting is specific to the model, please follow the instructions above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes,  set a high number (4-5).

Control panel

1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator light
4. Program indicator lights
5. START/Pause button with indicator light

Programs table

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
Values given for programs other than the eco-program are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options, and sensor calibration.

1. ECO – The eco program is suitable for cleaning normally soiled tableware, for this use, it is the most efficient program in terms of its combined energy and water consumption, and it is used to assess compliance with the EU Ecodesign legislation.
2. FAST WASH 40′ – Program for a limited quantity of normally soiled crockery. Ensures optimal cleaning performance in a shorter time.
3. INTENSIVE – Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).
4. MIXED – Mixed soil. For normally soiled dishes with dried food residues.
5. GLASS – Program for delicate items, which are more sensitive to high temperatures, for example, glasses and cups.

Modifying a running program
If a wrong program was selected, it is possible to change it, provided that it has only just begun: open the door, press and hold the ON/OFF button, and the machine will switch off. Switch the machine back on using the ON/OFF button and select the new wash cycle and any desired options; Start the wash cycle by pressing the START/Pause button and closing the door within 4 sec. If it takes more than 4 seconds the appliance automatically pauses and you must restart the appliance again by repeating the last operation.

Adding extra crockery
Without switching off the machine, open the door (START/Pause LED starts blinking) (be aware of HOT steam!) and place the crockery inside the dishwasher. Press the START/Pause button and close the door within 4 sec., the cycle will resume from the point at which it was interrupted.

Accidental interruptions
If the door is opened during the wash cycle, or if there is a power cut, the cycle pauses. Press the START/Pause button and close the door within 4 sec., the cycle will resume from the point at which it was interrupted.

Loading the racks

Upper rack bowls.
Load delicate and light dishes: glasses, cups, saucers, low salad

Foldable flaps with adjustable position

The side foldable flaps can be folded or unfolded to optimize the arrangement of crockery inside the rack. Wine glasses can be placed safely in the foldable flaps by inserting the stem of each glass into the corresponding slots.
Depending on the model:

• to unfold the flaps it is needed to slide it up and rotate or release it from the snaps and pull it down.
• to fold the flaps there is needed to rotate them and slide the flaps down or pull it up and attach flaps to the snaps.

Adjusting the height of the upper rack

• The height of the upper rack can be adjusted: a high position to place bulky crockery in the lower basket and a low position to make the most of the tip-up supports by creating more space upwards and avoiding collision with the items loaded into the lower rack.
• The upper rack is equipped with an Upper Rack height adjuster (see Ԓ figure), without pressing the levers, lift it up by simply holding the rack sides, as soon as the rack is stable in its upper position.
• To restore to the lower position, press lever A at the sides of the rack and move the basket downwards.
• We strongly recommend that you do not adjust the height of the rack when it is loaded.
• NEVER raise or lower the basket on one side only.

Lower rack
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm

Cutlery basket

• The basket is equipped with top grilles for improved cutlery arrangement. The cutlery basket should be positioned only at the front of the lower rack.
• Knives and other utensils with sharp edges must be placed in the cutlery basket with the points facing downwards or they must be positioned horizontally in the tip-up compartments on the upper rack.

When contacting our Service Provider, please state the codes provided on your product’s rating plate (left or right side on the edge of the dishwasher door).

• The model information can be retrieved using the QR code reported in the energy label.
• The label also includes the model identiԒ er that can be used to consult the https://eprel.ec.europa.eu database portal.

What to do if …
If you encounter an issue with your appliance, check the “What to do if…” chapter in the full version of the User Manual available on: www.ikea.com.

Technical data

FAQ

• Q: Can I use regular salt instead of salt designed for dishwashers?
  • A: No, only use salt specifically designed for dishwashers to prevent damage to the appliance.
• Q: How often should I refill the rinse aid dispenser?
  • A: Refill the rinse aid dispenser when the dark optical indicator becomes transparent for effective drying.

To download the full version visit www.ikea.com

References

• Hej! Welcome to IKEA Global

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>