BOSCH DSZ8WW1Y2 Kitchen Hoods Instruction Manual

BOSCH DSZ8WW1Y2 Kitchen Hoods

Installation instructions

General information

• Read this instruction manual carefully.
• Keep the instruction manual and the product information safe for future reference or for the next owner.
• The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.
• This instruction manual is intended for the installer of the optional accessory.
• Only a licensed expert may connect the appliance.
• Switch off the power supply before carrying out any work.

Safe installation

Observe the safety instructions when installing the optional accessory.

WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in it and suffocate.

• Keep packaging material away from children.
• Do not let children play with packaging material.

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

• Wear protective gloves.

Installation video

Fig. 1

Included with the appliance
After unpacking all parts, check for any damage in transit and completeness of the delivery. Fig. 2

Checking the units

• Check whether the fitted unit is level and has sufficient load-bearing capacity

Preparing the units

Requirement: The unit is suitable for the installation.

1. For the 80 cm appliance dimension: Establish a cut-out in the worktop.
   → Fig. 3 , → Fig. 4 , → Fig. 5 , → Fig. 6
   The angle between the cut surface and the worktop must be 90°.

2. For the 90 cm appliance dimension: Establish a cut-out in the worktop.
   → Fig. 3 , → Fig. 4
   The angle between the cut surface and the worktop must be 90°.

3. Ensure that the worktop has sufficient load-bearing capacity and stability.
   Use a heat- and humidity-resistant reinforcing material for any substructure.

4. Ensure that the fitted unit is still stable after the cut-outs have been made.

5. Remove any shavings.

6. Depending on the installation position, remove the back panel of the fitted unit.

Preparing the rails

1. In each case, slide a short rail into a long shelf.
2. In each case, screw in the rails loosely using two screws.
   → Fig. 7
   There are various screw positions depending on the cabinet width (90 cm/100 cm/120 cm.

Installing the rails

1. Place the prepared rails so that they are flush in the cut-out and push them apart ⁠.
   → Fig. 8

2. Installation situation A: Screw in the left- and righthand rails.
   → Fig. 9

3. Installation situation B: From the rear edge of the cut-out, measure 125 mm to the front and screw in the left- and right-hand rails ⁠.
   → Fig. 10

4. Installation situation C: From the rear edge of the cut-out, measure 125 mm to the front and screw in the left- and right-hand rails ⁠.
   → Fig. 11

5. Screw on the rails.
   → Fig. 12

Installing the cover strip

1. Screw in the 2 brackets on the rails.
   → Fig. 13

2. Put the cover strip in place and tighten the screws once again so that the cover strip is lying flush with the worktop.
   → Fig. 14

3. Stick the 2 sealing strips onto the gap between the cover strip and the worktop.
   → Fig. 15

Documents / Resources

| BOSCH DSZ8WW1Y2 Kitchen Hoods [pdf] Instruction Manual
DSZ8WW1Y2, LZ28WWY12, LZ29WWY12, DSZ8WW1Y2 Kitchen Hoods, DSZ8WW1Y2, Kitchen Hoods, Hoods
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>