LUCKY8 OFF ROAD D5 Proud Rhino Power Panel Instruction Manual

May 15, 2024
LUCKY8 OFF ROAD

PROUD RHINO D5 POWER PANEL

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel -

D5 Proud Rhino Power Panel

Step One:
Remove the lower side panels

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - Remove the lower side
panels

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - panel

Grasp underneath the leading edge of the panel and quickly pull outward releasing (7) clips then gently pull forward to release the front locking tab.
Step Two:
Remove the vertical trim pieces

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - screws

Locate and remove (2) Torx T25 screws

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - Gently
pull

Gently pull the vertical trim piece in two steps as shown releasing (4) clips

Step Three:
Remove the upper trim panels

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - panel
outward

Gently pull the panel outward releasing (3) clips

Step Four:
Remove the rubber insert

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - holding

Note: there are (6) bottom tabs and (3) upper tabs holding the insert in place

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - bottom
tabs

Gently pull up to release the (6) bottom tabs

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - bottom
tabs1

Gently pull down to release the (3) upper tabs

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - bottom
tabs2

Slowly pull the rubber insert out and set aside (it will not be reused)

Step Five:
Remove the cigarette lighter housing

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - housing

Locate and remove (3) Torx T25 screws securing the cigarette lighter housing and set aside they will no longer be needed
Note: The upper hole will be used to secure the Proud Rhino Power Panel (shown later)

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - housing1

Once the screws are removed gently pull the cigarette lighter housing forward to remove

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - main
battery

Push the detent to release the electrical connection. There are three wires in the connector, either disassemble the connector or cut the wires completely.
(Note: before disassembling or cutting the wires disconnect the vehicles main battery to avoid any chance of an electrical short)

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - main
battery1

You will only need (2) of the (3) wires; the Black (ground) and the yellow/brown (+12v). The blue/white wire was for the cigarette lighters backlight and should be isolated away from the other two wires.

Step Six:
Install the Proud Rhino Power Panel

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - main
battery2

Insert the Power Panel into the space where the rubber insert was located. Line up the threaded hole on the Power Panel with the upper cigarette lighter hole.
The Proud Rhino Power Panel is pre-threaded to accept a 10-32 screw. I used (2) Stainless Button Head Cap Screws 10-32 x ½” along with (2) #8 Stainless Flat Washers to complete the installation
Step Eight:
Reinstall everything in the reverse order, reconnect the battery, start your vehicle, sit back and enjoy your new Proud Rhino Power Panel.

LUCKY8 OFF ROAD D5 Proud Rhino Power Panel - Power
PanelLUCKY8 OFF ROAD D5 Proud Rhino
Power Panel - Power Panel1

The nice thing about this Proud Rhino product sold at Lucky 8 Off Road Equipment is the quality and versatility. The panel comes with standard Carling switches so you have the option of purchasing MUD UK Switch Legends (sold @ Lucky 8) or I had switch covers from a previous build which are show here.

PROUD RHINO D5 POWER PANEL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals