YELLOW BLINDS Burton Flax Cordless Linen Fabric Window Treatment Installation Guide
- May 15, 2024
- YELLOW BLINDS
Table of Contents
- Installation
- Prepare necessary tools
- STEP 1: DETERMINE INSIDE/CEILING, FLUSH, WALL OR OUTSIDE MOUNT
- STEP 2: ATTACHING SUPPORT RODS
- STEP 3: MOUNTING THE SHADE
- STEP 5: HOW TO OPERATE
- CLEANING & CARE
- Ready-Made Blinds and Shades Warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
YELLOW BLINDS Burton Flax Cordless Linen Fabric Window Treatment
Installation Guide
Installation
Check Components
Roman Shade Components | Shade Width Up to 39 in | Shade Width 47 in and up |
---|
Mounting Bracket
| x2| x3
Screws
| x4| x6
Anchors
| x4| x6
Support Rod Screws
| x2| x2
Prepare necessary tools
Screw driver| | Measuring Tape|
---|---|---|---
Pencil| | Drill / Drill Bits|
Hammer| | Ladder|
STEP 1: DETERMINE INSIDE/CEILING, FLUSH, WALL OR OUTSIDE MOUNT
a. Inside/Ceiling or Flush Mount
(A minimum 1 inch depth is required or 2 inches depth for flush mounts.)
-
Position brackets approximately 2 inches from the ends of the headrail.
-
Mark the bracket locations upward through the holes with a pencil.
-
Use the screws and anchors in the top bracket holes to attach your brackets.
b. Wall or Outside Mount
(A minimum 1/2 inch flat wall space is necessary)
-
Position brackets approximately 2 inches from the ends of the headrail. If your shade had a third bracket provided, position middle brackets to align with pre-drilled holes in the headrail.
-
Mark the bracket locations through the rear holes with a pencil.
-
Use the screws and anchors in the rear bracket holes to attach your brackets.
STEP 2: ATTACHING SUPPORT RODS
Swing the support rods into the square brackets that are attached to the back
of the shade. Snap in place by pressing firmly sideways and install support
rod screws to lock into position.
STEP 3: MOUNTING THE SHADE
- Attach front lip of the headrail into the front lip of each mounting bracket.
- Rotate and push headrail back into the spring tab until it clicks into place.
STEP 5: HOW TO OPERATE
To lower your blinds, simply pull to the desired position and release.
To raise your blinds, push up to desired position and release.
CLEANING & CARE
Periodic cleaning is suggested. For best results, use a vacuum cleaner. For spot-removal use a mild fabric cleanser, suitable for polyester and follow the manufacturers directions.
Ready-Made Blinds and Shades Warranty
Limited One Year Warranty from the Date of Purchase
What is Covered:
All of our shades are warranted against manufacturer defects in materials or workmanship provided that. you are the original purchaser of the product, and the product was installed according to our instructions.
What is Not Covered:
-
Normal wear and tear
-
Consumer damages caused by accidents, alterations, abuse of the product, exposure to salt air,
misuse, or damages from pets or insects. -
Damages resulting from removal and reinstallation in the same or any other window or application, or failure to follow instructions, such as measurement, installation, cleaning, and maintenance.
-
Any products that, with the passage of time, has yellowing or cracking of plastic parts
-
Wrong measurements are not covered by the warranty and are not refundable
To report shipping damages:
If damage occurred during shipping, please call 1
866-999-6188 immediately and report
within 14 calendar days or else you may be denied for your damaged product
Obligations to the consumer:
The obligations of the seller are limited to the repair or replacements of
parts or products found to be defective. The seller will determine if the
product is defective or not and may replace the product. If the product is
found to have manufacture defects, we will repair or replace the product.
Colors do vary from lot to lot, and may not match original product exactly.
Discontinued items will be replaced with the most current product of the same
price.
Your Rights under State law:
This limited warranty gives you specific legal rights, and you may have other
rights, which vary from state to state
Contacting us:
If you believe your shade has a manufacturing defect, please call 1
866-999-6188.