ACEUP AWPE3500 Electric Pressure Washer Instruction Manual

ACEUP AWPE3500 Electric Pressure Washer

Product Information

Specifications:

• Model: AWP E3500, AWP E3800
• Pressure: High Pressure
• Double-insulated construction
• Usage: Pressure Cleaning

Product Usage Instructions

Important Safety Tips and Precautions:

• Always read the instructions before using the machine to reduce the risk of injury.
• Avoid pointing the gun at humans, animals, the machine body, power supplies, or any electrical appliances.
• Machine should not be left unattended while connected to portable mains.

General Safety Precautions:

• Avoid using the pressure cleaner in cold weather until all parts are checked and confirmed to be functioning properly.
• Avoid exposure to rain or damp locations to reduce the risk of electrical shock.
• Always wear safety goggles, safety glasses with side shields, and a face shield when operating the product.

Warning – Proper Use of the Pressure Cleaner:

• Do not place any body parts in the stream of water to avoid injury.
• To reduce the risk of injury from kickback, securely hold the spray lance with both hands when the machine is on.
• Failure to use in dry conditions and observe safe practices can result in electric shock.

Assembly Instructions:

• Follow the step-by-step assembly instructions provided in the manual.
• Ensure all parts are securely attached before operating the pressure cleaner.

Operating Instructions:

• Read and understand the owner’s manual before using the product.
• Avoid pointing the gun at any person or animal to prevent injury.
  Do not use damaged extension cords and do not pull on the cord to disconnect the product.

Clean-up and Storage:

• After use, turn off the machine and disconnect from power sources.
• Clean the pressure cleaner and store it in a dry place away from moisture.

Contents:

• Important Safety Tips and Precautions
• General Safety Precautions
• Warning – Proper Use of the Pressure Cleaner
• Assembly Instructions
• Operating Instructions
• Clean-up and Storage

Frequently Asked Questions (FAQ):

• Can I use the pressure cleaner in cold weather?
  Before starting the pressure cleaner in cold weather, check all parts and ensure they are in good working condition.

• What safety gear should I wear when operating the pressure cleaner?
  Always wear safety goggles, safety glasses with side shields, and a face shield to protect your eyes and face.

• Can I use an extension cord with the pressure cleaner?
  It is not recommended to use an extension cord with the pressure cleaner. If necessary, use only extension cords that meet specific requirements as outlined in the manual.

IMPORTANT SAFETY TIPS

• Never point the high-pressure nozzle at people or animals.
• Never drink alcohol or use drugs while operating the pressure cleaner.
• Never operate the pressure cleaner while standing in water.
• Never touch the electrical plug with wet hands.
• Never let electrical connections rest in water.
• Never operate pressure cleaner without the water tumed on.
• Never use hot water with this pressure cleaner.

IMPORTANT SAFETY PRECAUTIONS

WARNING: When using this product, basic precautions should always be followed, including the following:

1. Read all instructions before using the product. Save all safety instructions.
2. Do not operate the pressure cleaner when fatigued or under the influence of alcohol or drugs.
3. Risk of injection or injury – do not direct the high pressure water stream at any people or animals.
4. Do not allow children to operate the pressure cleaner at any time.
5. To reduce the risk of injury, close supervision is necessary when the pressure cleaner is used near children.
6. Know how to stop the unit and reduce pressure immediately. Be compietely familiar with the controls.
7. Stay alert – always be aware ofwhere you are directing the high pressure spray
8. Keep cleaning area clear of all people.
9. Keep good footing and balance at all times – do not overreach or stand on an unstable support.
10. The work area should have adequate drainage to reduce the possibility of a fall due to slippery surfaces.
11. Follow the maintenance instructions specified in the manual.
12. To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet hands.

GENERAL SAFETY PRECAUTIONS

1. Intended for outdoor household use only.
2. High-pressure hose can develop leaks from wear, abuse, Kinking etc. Do not use a damaged hose.
3. Do not use the pressure cleaner in areas near combustible materials, combustible fumes, or dust.
4. Some chemicals or detergents may be harmful if inhaled or ingested causing severe injury. Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions included with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
5. Before starting the pressure cleaner in cold weather, check all ofthe parts of the equipment and be sure that ice has not formed. Do not store the unit anywhere thatthe temperature will fall below 0° C (32° F).
6. DO NOT MAKE ANY MODIFICATIONS TO ANY OF THE COMPONENTS! Units with broken or missing parts, or without the protective housing or covers should NEVER be operated
7. Keep the high-pressure hose connected to the pressure cleaner and the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous, and may cause injury
8. Do not leave the pressure cleaner unattended while the power switch is ON.
9. Keepwater spray away from electrical wiring or fatal electric shock may result.

SYMBOLS

The labels on your tools and manual may show symbols. These represent important information about the product or instruction on its use.

SERVICING OF A DOUBLE-INSULATED APPLIANCE

In a double-insulated product, two systems of insulation are provided instead of grounding. No means of grounding is provided on a double-insulated product, norshould a means for grounding be added to the product. Servicing a double- insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double- insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. This symbol may also be marked on the product.

USE OF EXTENSION CORDS

Use ofan extension cord with this product is NOT RECOMMENDED. If you must use an extension cord, use only extension cords that are intended foroutdoor use. These cords are identified by a marking “ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES, STORE INDOORS WHILE NOT IN USE.” Use only extension cords having an electrical rating not less than the rating ofthe product. Examine extension cord before use. DO NOT USE DAMAGED EXTENSION CORDS! Do not pull on cordto disconnect from receptacle, always disconnect by pulling on plug. Keep cord away from heat and sharp edges. Always disconnect the extension cord fromthe receptacle before disconnecting the product from the extension cord.
WARNING – To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands.

• Do not use the appliance if a supply cord or important parts ofthe appliance are damaged, e.g. safety devices, high pressure hoses, trigger gun.
• If an extension cord is used, the plug and socket must be of watertight construction.
• WARNING: Inadequate extension cords can be dangerous
• Remove the plug from the socket-outlet during cleaning or maintenance and when replacing arts or converting the machine to anotherfunction.

PROPER USE OF THE PRESSURE CLEANER

THIS UNIT IS INTENDED FOR USE WITH COLD WATER ONLY! DO NOT USE HOT WATER IN THIS PRESSURE CLEANER.

1. Operate the pressure cleaner at no more than the fluid pressure rated forthe pressure cleaner. Never run the pressure cleaner without a water supply. Running the unit without a water supply will cause irreparable damage to the unit.
2. Make sure that the water supplyyou use for the pressure cleaner is not dirty, sandy, and does not hold any corrosive chemical products. Using a dirty water supply will compromise the long life of the pressure cleaner.
3. CAUTION – The pressure cleaner can be used for a variety of applications including washing cars, boats, patios, decks, garages etc. where high pressure is necessary to remove dirt and debris
4. High-pressure water flow can damage the work surface if not used properly! See the section titled “Operating Instructions” for more details. Always test the spray in an open area first.
5. NEVER move the unit by pulling on the high pressure hose. Use the handle provided on the top of the unit. Always hold the high pressure gun and wand with two hands. Keep one hand on the gun/trigger, while supporting the wand with the other hand (see diagram).
6. When dispensing detergent, the pressure cleaner applies detergent to the cleaning area at low pressure only. Once the detergent has been applied, spray the detergent off of the work area by using the adjustable nozzle.

Unpacking the Carton

After opening the carton, please remove all parts and check them against the following list of components that are included:

Product Overview

1. Inlet connector
2. Inlet hose not included)
3. Tap(notincluded)
4. Power cable
5. Gun holder
6. Inlet
7. Power cable Hook
8. Wrisel
9. Rocking handle
10. Machine handler
11. Reel wrieel
12. Start/Stop switch
13. Outlet
14. High pressure hose
15. Gun safety lock
16. Gun lance
17. Angle nozzle
18. Nozzle cleaner
19. Threaded Connection
    The accessories are subject to random objects. Reserve the right to change.

ASSEMBLY INSTRUCTION

• Step 1
  • Insertthe lance(C) intothe gun(E) . Push and turn the lance(C) clockwise ontothe gun (E) until hand tight to lock it in place. When the pieces are joined properly, you cannot separate the two components by pulling straightout on the gun (E). Insert the nozzle In the same manner. depending upon which attachment Is best sulted to the surface you are cleaning. Only one attachment can be Inserted Intothe gun at a time. All attachments must be inserted into the gun for proper use.

  * Insert the nozzle(D) into the lance(E), as quick-connect type, you just need push it onto lance(E) directly and powerful until hand tight to lock it in place. When the pieces are joined properly, you cannot separate the two components by pulling straight out on the lance(E). Insert the other nozzle In the same manner, depending upon which attachment is best suited to the surface you are cleaning. Only one attachment can be Inserted Into the lance(E) at a time. All attachments must be Inserted Into the lance (E) for proper use.

• Step 2
  Screw the washer handle tight to the main body as below fig. The screws will be packed together with the main body, pls kindly check and find it when unpacked .

• Step 3
  Attach the high pressure hose(F) tothe pressure cleaner water outlet. Insert and quick-connect it tight to avoid leakage.When the pieces are joined properly, you cannot separate the two components by pulling straight out from the water outlet. Push the “Button” according to the direction of arrow, then you can pull outthe high pressure hose.

• Step 4
  Attach the high pressure hose(F) to the gun(E). Insert and quick-connect it tight to avoid leakage. When the pieces are joined properly, you cannot separate the two components by pulling straight out from the gun(E). Push the hose lock button, then you can pull out high pressure hose.

• Step 5
  Insert the detergent nozzle(J) into the gun(E). Push and tum the detergent nozzle(J) clockwise onto the gun(E) until hand tight to lock it in place. When the pieces are joined properly, you cannot separate the two components by pulling straight out on the gun(E).

• Step 6
  Attach the hose connectorto pressure washer. Before attaching the connector to the male fitting, remove the plastic cap, which is inserted onto the male fitting on the pressure washer before shipping. This plastic cap can be discarded once removed. After both components have been installed, attach the garden hose with connector screw on the pressure washer. Connect the garden hose to the waterspout.

OPERATING INSTRUCTIONS

THIS UNIT IS INTENDED TO BE USED WITH COLD WATER ONLY! DO NOT USE HOT WATER IN THIS PRESSURE CLEANER!

Starting Up
After connecting the pressure cleaner to your cold water supply, proceed as follows:

• Make sure that the ON/OFF switch is in the OFF position.

• Connect the garden hose to the inlet fitting.

• Insertthe adjustable spray nozzle into the gun as per assembly step #1

• Install the handle to the machine main body, as per assembly step#2.

• Connectthe high pressure hose to the high pressure outlet fitting as per assembly step #3.

• Connect the high pressure hose to the gun, as per assembly step #4.

• Connect the gun to the specified detergent nozzle, as per assembly step #5.

• Open the water supply valve completely.

• Before turning the unit on, press the gun trigger to bleed all the remaining air out of the pump and hose.

• Start the pressure cleaner by turning the on/off switch to the on position and squeeze the trigger. REMINDER: Motor does not run continuously, only when the trigger is squeezed.
  WARNING – RISK OF INJECTION! Unit will start spraying when trigger is squeezed.

• When turning the unit off after use, high pressure still exists inside the hose and unit. Point the gun in a safe direction and discharge the excess pressure.

• NEVER direct the high pressure water stream at people or animals.

Automatic On/Off
The pressure cleaner is equipped with an automatic on/off switch. The pressure cleaner will only run when the power switch is in the ON position and the trigger on the gun is squeezed. When you release the triggerto stop spraying water through the gun, the motor on the pressure cleaner will automatically shut off. Simply squeeze the trigger again to resurne using the cleaner. To stop using the pressure cleaner, release the trigger and switch the unit to the OFF position. The unit should be tumed completely OFF while not in use or while unattended.

Bleeding The Gun
It is very importantto bleed the gun before using the pressure cleaner. Refer to the “Assembly Instructions” to assemble the pressure cleaner To bleed the gun, simply connect the garden hose to the pressure cleaner and squeeze the trigger BEFORE tuming the electncal supply on. This allows any air trapped inside the pressure cleaner and gun to be removed before using the unit. Continue holding trigger for approximately one minute to allow any excess air out of the unit. Water will flowthrough the gun at low pressure during this procedure. For more bleeding tips, see the section titled “Operating Instructions.”

Gun Safety Lock

This pressure cleaner is equipped with a gun trigger safety lock. When not using the pressure cleaner, use the safety lock to keep from accidentally engaging the high pressure spray.

Nozzle

• Select proper nozzle ,pull the collarand insert the nozzle, then put the collar to retum to place.

• Choose the best nozzle for the job.

• Waming:Please confirm the nozzle is pluged in position and the nozzle holder is returned to
  position before squeezing the trigger. Detail of Iritended use see items (1)(5)below;

  1. 0° nozzle,Red, Fine spot spray means delivering a high-pressure pencil-point jet stream,
     It is used to cut heavy dirt deposits In a small concentrated area. It is ideal for dissolving stubbom substances, like tar and grease spots on concrete, or for removing caked mud from equipment.
     It is also used to clean hard-to-reach arees including the facades of 2-stpry buildings or undersides of lawn mowers and tractors
     Note: Care should be taken when setting nozzle spray to avoid permanently gouging wood or damaging fragile surfaces.

  2. 15° nozzle, Yellow, for intense cleaning jobs on hard surfaces thatcan withstard the high-pressure Applicatioris include stripping paint, removing: oil steins, grease heavy mildew stalns, and rust fromsteel.

  3. 25° nozzle, Green, for cleaning hornesiding, brick patios, wood decks, driveways, sidewalks, cars or fumiture.

  4. 40° nozzle, White, for clearing iterns suchascars, trucks, boals, patio fumiture, or lawn equlpment.

  5. 75° nozzle, Black, for spraying foam.
     Warning: High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment or the appliance itself.
     Do not direct the jet against yourself or others in order to clean clothes or foot-wear.

Detergent Nozzle
The detergent nozzle will allow you to apply many forms of liquid detergent onto the work surface. Fill the container with detergent only. Do not put any water into the container. The pressure cleaner will mix water and detergent automatically. When finished applying the detergent to the work surface, insert the adjustable spray nozzle, and remove the detergent by using the high pressure spray.

USING DETERGENTS

THE PRESSURE CLEANER WILL DISPENSE DETERGENT AT LOW PRESSURE. USE THE ADJUSTABLE SPRAY NOZZLE TO RINSE CLEAN. BIODEGRADABLE DETERGENTS ARE SPECIFICALLY FORMULATED TO PROTECT THE ENVIRONMENT AND YOUR PRESSURE CLEANER. THESE
DETERGENTS WILL NOT CLOG THE FILTER AND WILL PROTECT THE INTERNAL PARTS OF THE PRESSURE CLEANER FOR A LONGER LIFE.

• Step 1
  Separate the nozzle from the detergent container by tuming the detergent reservoir counter clockwise and separating the two components

• Step 2
  Fillthe detergent container with approved detergent. Pour the detergent slowly into the reservoir using a funnel. Re-attach the two components by re- inserting the nozzle back onto the detergent reservoir and tuming clockwise.

CLEAN-UP AND STORAGE

Shutting Down the Pressure Cleaner
WHEN FINISHED USING THE PRESSURE CLEANER, FOLLOW THESE STEPS TO SHUT DOWN THE UNIT:

• Turn the pressure cleaner to the OFF position.
• Turn offthe water supply.
• Before disconnecting high-pressure hose connection, point the gun in a safe direction and discharge the high-pressure water.
• Disconnect high-pressure hose from the pressure cleaner and gun.
• Disconnect garden hose from the pressure cleaner.
• Remove quick coupler fitting from garden hose and attach to the nipple portion ofthe fitting installed on the pressure cleaner for storage.
• Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from inlet and outlet fittings.
• Remove Water Intake Filter and flush with waterto remove dirt or debns. Return filter once cleaned.
• Drain detergent reservoir and flush with running water.
• Wipe away any remaining water on all parts and fittings.
• Engage the gun safety lock.
• Store the pressure cleaner, parts, and accessories in an area with a temperature above 0° C (32° F).

Winterizing and Long-Term Storage
FOLLOW ALL OF THE ABOVE SHUT-DOWN PROCEDURES, ADDING THE FOLLOWING STEPS….

• After disconnecting the water supply, and before disconnecting the high-pressure hose, turn the pressure cleaner on for 2-3 seconds, until any remaining water in the pump exits.
  TURN UNIT OFF IMMEDIATELY.CONTINUED USE OF THE PRESSURE CLEANER WITHOUT WATER SUPPLY ATTACHED WILL CAUSE SEVERE DAMAGE TO THE UNIT!

• Always store the pressure cleaner, parts, and accessories in an area with a temperature above 0° C (32° F).
  WARNING: FAILURE TO COMPLY WITH THESE STORAGE INSTRUCTIONS WILL RESULT IN DAMAGE TO THE PUMP ASSEMBLY.

Maintenance

• This pressure cleaner is supplied with a closed lubrication system, so no addition ofoil is needed.
• Check al hoses and accessones for damage prior to use
• Check the inlet filter periodically for deposits. Clean this filter regularly for maximum performance.

CLEANING TIPS

WARNING: ALWAYS TEST THE SPRAY IN AN AREA FREE AND CLEAR OF PEOPLE AND OBJECTS BEFORE YOU SPRAY AT THE INTENDED CLEANING SURFACE.

Wood and Vinyl Decks
Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. For optimal results, reduce your work area to smaller sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure. DO NOT LET THE CLEANSER DRY. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan spray keeping the tip of the spray nozzle at least 6-9 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray. Caution: For softer woods, increase the distance from the cleaning area.

Cement Patios, Stone, and Brick
Rinse cleaning and surrounding area with fresh water. If using detergent, fillthe detergent reservoir and apply to the area being cleaned at low pressure. Rinse at high pressure using the fan spray in a sweeping motion keeping the tip ofthe spray nozzle at least 3-6 inches fromthe cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

Cars, Boats, and Motorcycles
Rinse cleaning and surrounding area with fresh water. If using detergent, fill the detergent resenvoir and apply to the area being cleaned at low pressure. To achieve the best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes, but do not let the detergent dry. Rinse at high pressure using the fan spray in a sweeping motion keeping the tip of the spray nozzle at least 8 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray. Wipe surface dry for a polished finish.

Barbecue Grills, Power Equipment, and Garden Tools
Rinse cleaning and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. Allow the detergent to rest on the surface for a few minutes, but do not let the detergent dry. Rinse at high pressure using the fan spray keeping the tip of the spray nozzle at least 1-3 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

TECHNICAL DATA

Level ofsound pressure measured according to ISO 3744:

• LpA (sound pressure) dB (A) 90.3
• Кра (sound pressure) dB (A) 3
• LwA sound power) dB (A) 105
• KwA (sound power) dB (A) 3
• Weightec root mean square acceleration value: < 2.65 m/s2

GUARANTEE

Refer to the enclosed guarantee conditions for the terms and conditions of guarantee.

ENVIRONMENT

Should your machine need replacement afler extended use, do not put it in the domestic waste but dispose of it in an environmentally safe way.

TROUBLE SHOOTING TIPS

• WHEN THE SWITCH IS IN THE “I” POSITION THE MACHINE WILL NOT START

  • PROBABLE CAUSE
  • Electrical socket is faulty
  • Voltage is inadequate
  • Power cord is not plugged in
  • SOLUTION
  • Check plug, socket, fuses
  • Check whether the voltage is adequate
  • Plug in power cord

• THE PUMP DOES NOT REACH ADEQUATE PRESSURE OR FLUCTUATES

  • PROBABLE CAUSE
  • Water inlet filter is clogged
  • Pump is drawing air
  • Suction valves are clogged/wom
  • Dia meter of garden hose too small
  • Water supply is restricted
  • Insufficient water supply
  • SOLUTION
  • Remove and clean filter
  • Tighten connections/bleed system
  • Clean or replace valves
  • Replace with ¾ inch garden hose
  • Check hose for kinks or leaks
  • Fully open water source

• THE PRESSURE CLEANER HAS OR WILL NOT MAINTAIN PRESSURE

  • PROBABLE CAUSE
    Excessive air in waterline and pump

  • SOLUTION
    Turn unit and water supply off/ Bleed system/Hold trigger down

• THE PRESSURE CLEANER MAKES EXCESSIVE NOISE

  • PROBABLE CAUSE

  • Intake is blocked

  • Valves are worn, dirty, or clogged

  • Filter is dirty

  • SOLUTION

  • Check the intake valves

  • Check, clean or replace valves

  • Check, clean, or replace filter

  • THE MOTOR STOPS RUNNING WHILE IN USE

  • PROBABLE CAUSE
    Net voltage lower than suggested

  • SOLUTION
    Check whether the voltage is adequate

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>