MULTICROSS 027.03D 3D Brave User Manual
- May 15, 2024
- MULTICROSS
Table of Contents
USER MANUAL
027.03D MULTICROSS 3D BRAVE GREEN
Manual in your language?
Check the back cover
OVERVIEW
CASE
- Horizontal laser exit
- Front vertical laser exit (V1)
- Side vertical laser exit (V2)
- On/Off/Transport security switch
- Battery compartment
- Tripod thread 1/4”
- Power socket
- Keypad
KEYPAD
A. H-button for horizontal lines / Power button
B. V-button for vertical lines
C. Receiver button
D. Power indicator
E. Receiver indicator
F. Warning indicator
TURNING TABLE OPTIONAL ACCESSORY
a. Rotation point
b. Fine tuning
c.Shifting plate
d. Tripod thread 5/8”
- Slide the device onto the turning table
- Manually rotate the laser to the desired position
- Using the fine tuning [b] the shifting plate [c] will move and brings the laser line is the exact position. (plumb stays in position)
QUICK START GUIDE
KEYPAD| NAME| FUNCTION|
---|---|---|---
A| H-button / Power button| Press| (De-)activate horizontal laser lines
| | Hold| Switch ON device whit pendulum locked (for manual slope)
B| V-button| Press| (De-)activate vertical laser lines
C| Receiver button| Press| (De-)activate the receiver mode (Pulse)
D| LED Power indicator| No| The device is switched OFF
| | Green| The device is switched ON
E| LED receiver indicator| No| Receiver mode OFF, detection with receiver is
not possible
| | Red| Receiver mode ON, laser line pulses, detection with receiver is
possible
F| Orange, flashing fast| Orange, flashing slow| Slope active (pendulum is
locked, laser not levelled)
| Orange, flashing fast| Out of self-levelling range
SAFETY
Please read the safety instructions is provided in the separate booklet
provided with the device.
LASER RADIATION – Class 2 Laser product. – Do not stare into beam
BATTERY
his laser can be used with the supplied battery (7.4V, 2200 mAh) or using the
supplied USB-C power adapter. The battery will charge when it is in the device
while the power adapter is connected.
The device can be used while charging.
FIRST TIME USAGE
Remove all protection foils.
Place the provided LI-ION battery in the device by opening the battery cover
[05]. Make sure the batteries are fully charged.
USE
- AUTO-LEVELLING
Slide the On/Off/Transport security switch [04] to the “ON” position. The
laser is switched on, the pendulum levelling mechanism is released, and the
instrument is able to level itself.
The laser can level itself in a range of approx. 3° in
every direction. This means the laser can show 100% horizontal or vertical
lines when placed on a sloped surface of approx. 3° maximum.
In case the laser is placed on a surface that exceeds the 3°, a levelled
horizontal or vertical laser line will no longer be possible.
The warning indicator [F] will flash fast and the laser lines will turn off.
Place the laser device on a flatter surface, within the levelling range of 3°
if possible. The laser will self level automatically when placed within its
levelling range.
SWITCHING ON/OFF LASER LINES
When switching on the device, all 3 laser diodes will be activated.
HORIZONTAL LASER LINES
To change the projected horizontal laser lines, press the H-button for
horizontal lines [A].
- Press the H-button [A] a first time to switch off the horizontal laser line (V1) [02].
- Press the H-button [A] a second time to switch on the horizontal laser line (V1) [02].
- …(these two previous steps will repeat)
NOTE
We advise to set the horizontal line on your working height, using a tripod.
VERTICAL LASER LINES
To change the projected vertical laser lines, press the V-button for vertical
lines [B].
- Press the V-button [B] a first time to switch off all verical laser lines.
- Press the V-button [B] a second time to switch on the front vertical laser line (V1) [02].
- Press the V-button [B] a third time to switch on the side vertical laser line (V2) [03].
- Press the V-button [B] a fourth time to switch on both vertical laser line (V1+V2) [02][03].
- … (these four previous steps will repeat)
NOTE
When both vertical lines are switched on, you can measure an exact angle of
90° or show a plumb line (imaginary line between the cross on the floor and
the cross on the ceiling)
SLOPE MODE
Slide the On/Off/Transport security switch [04] to “OFF” so the laser beams
are turned off and the transport lock is active (pendulum is blocked).
Hold the H-button / Power button [A] for approx.
3 seconds. All laser lines will switches on without loosen the transport
security (pendulum is still locked in position). The warning indicator [E]
flashes slow. This to warn you the laser is not levelled!
Hold the H-button / Power button [A] again for approx/ 3 seconds to shut down
the laser in slope mode.
MANUAL SLOPE
You can physically position the device at the desired slope by using an
inclined surface or a slope adapter (optional accessory).
NOTE
In slope mode, the laser lines no longer levelled automatically. A slow
flashing warning indicator [F] will remind you the pendulum is blocked and the
laser is not able to level.
RECEIVER MODE
Press the receiver button [C] to turn on the receiver mode (pulse). When this
mode is activated, the receiver indicator [E] will light up.
At this moment, laser lines can be picked up by a laser receiver.
Press the receiver button [C] again to turn off the receiver mode (pulse).
NOTE
All Futech laser will use 10Khz as frequency in receiver mode. Only receivers
that can detect laser lines at 10KHz are compatible.
TECHNICAL SPECIFICATIONS
| 027.3DG MULTICROSS 3D BRAVE GREEN
---|---
Visibility|
Accuracy| ± 2 mm / 10 m
Range with receiver| 2x 40 m
Levelling range| ± 3°
Levelling| Pendulum levelling
Slope fucntion| Manual (via pendulum lock)
Tripod thread| 1/4”
Laser wavelenght| 515 nm
Laser classifi cation| Class 2, < 1mW
Power supply| Li-Ion battery 7.4V, 2200mAh
Protection| IP54
Dimensions (l x w x h)| 116 x 82 x 120 mm
Weight| 0,400 kg
Operation temperature| -5°c ~ +40°c
DECLARATION OF CONFORMITY
Futech (Belgium) declares under its own responsibility that this device:
– 027.3DG, MULTICROSS 3D BRAVE GREEN is in conformity with the standards
EN IEC 61326-1:2021,
IEC 60825-1:2014
following the provisions of Directive(s) 2014/30/EU.
230331090855
Potential misprints are reserved. Images used are not strict. All features,
functionality and other product specifications are subject to change without
notice or obligation.
| Facebook
@futechtools
---|---
| LinkedIn
futechtools
| World Wide Web
futech-tools.com
| YouTube
@futechtools
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>