Leganza 6 Person 90 Jet 230V Hot Tub User Guide

June 4, 2024
Leganza

6 Person 90 Jet 230V Hot Tub
User Guide

IMPORTANT Failure to read the Owner’s Manual and follow its instructions may result in unsafe operation, permanent damage to your hot tub, and/or personal harm.

COMPONENT LEGEND

Leganza 6 Person 90 Jet 230V Hot Tub - COMPONENT
LEGEND

STEP 1: FILL IT UP!
Do not plug in or turn on the connected breaker before completely filling your hot tub with water.
Before you can start soaking, you’ve got to add some water. Here’s how to achieve the perfect water level.

  1. Remove the filter and insert the hose into the filter compartment.
  2. Turn on the water and wait.
  3. Fill until the water is 1” above the highest jet, but not more than 6” below the top of the spa. Replace the filter after filled.

HOT TUB TIP:
Remove the door panel to check inside the equipment compartment for water leaks while filling the tub. If there’s a leak or if anything doesn’t go according to plan, we’re here to help!

STEP 2: POWER IT UP!

Put the ‘hot’ in the ‘hot tub’ with electricity! Ahhh, there’s nothing better than a warm water massage!
110 Volt: Plug the GFCI cord into the designated wall outlet. In about 24 hours, you’ll be ready to soak!
220 Volt: Turn on the breaker in the spa subpanel after a licensed electrician installs power. In just 6-8 short hours, you’ll be relaxing in warm water.
HOT TUB TIP:
Your hot tub will automatically heat to 100°F at startup. Use the +/- buttons to adjust the temperature. After 5 seconds, the current temperature will appear, climbing each degree until it hits that perfect temp.

CUSTOMER SERVICE

888-772-4359
AHSService@WatkinsMFG.com

STEP 3: CLEAN IT UP!
Stay safe while hot tubbing! Follow these directions to protect yourself and your hot tub.

  1. Buy chemicals and test strips from your local hot tub or pool store to help sanitize your tub and balance your tub’s pH, total alkalinity, and calcium hardness.
  2. Get that jet pump going at high speed and leave the jets running for 15 minutes before adding in your chemicals.
  3. Break out the test strips to check your levels. Based on the results, add chemicals as needed until your water is balanced and safe to soak in. Are levels too high? Too low? Check your Owner’s Manual for the next steps.

HOT TUB TIP:
****Don’t know which button starts your jets?
Find one of the buttons below on your control panel!

FINALLY, RELAX IT UP!
Congratulations! Your tub is filled up, your water is balanced, and the temp is just right. Now comes the fun part. Step in, relax, and unwind!
HOT TUB TIP:
Your hot tub temperature maintains itself with a sensor, just like a refrigerator.
Keep your hot tub plugged in and turned on with the cover secured, so you can enjoy your hot tub whenever you’re ready!

HOT TUB TIP:
Don’t forget to shock your tub weekly!
Add your sanitizer of choice (bromine or chlorine – the granular kind) and potassium monopersulfate (MPS) shock, making sure that your high-speed pump is activated.
Run the jets for 15 minutes, with the cover off, to circulate the water and clean every inch of the tub.

RECOMMENDED RANGES:

Total Alkalinity: Between 80-120 PPM
Leganza 6 Person 90 Jet 230V Hot Tub - RANGES
Calcium Hardness: Between 50-150 PPM
Leganza 6 Person 90 Jet 230V Hot Tub - RANGES 2
Sanitize: Between 3-5 PPM
Leganza 6 Person 90 Jet 230V Hot Tub - RANGES 3
pH Level: Between 7.2 and 7.8
Leganza 6 Person 90 Jet 230V Hot Tub - RANGES 4
Parts Per Million

YOUR HOT TUB INFO
****Collect the following information and keep it in a safe place.
Date Purchased:
Purchased From:

Spa Model:___
Serial Number:____

© 2021 Watkins Wellness, PN 63593FR Rev. A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals