LTS LTWB-5AC-12 Wireless Bridge Owner’s Manual
- May 15, 2024
- LTS
Table of Contents
LTWB-5AC-12
Wireless Bridge
LTWB-5AC-12 Wireless Bridge
The wireless bridge can be applied in industries, such as wireless video security, railway, transportation, power and other industries, wireless video/data transmission, wireless coverage, carrier wireless backbone network construction, Wi-Fi wireless coverage, rural information construction, and wireless network coverage. The longdistance transmission of the device can guarantee multi-channel HD video transmission.
- All gigabit LAN ports
- TDMA supported
- Quick match through DIP switch
- Visualized topology management
- Up to 3 miles wireless transmission distance
Specification
| Model | LTWB-5AC-12 |
|---|---|
| Wireless Parameter | Max. Transmission Rate of Air Interface |
| Wireless Standard | IEEE 802.11/a/n/ac |
| Working Frequency Band | 5180 to 5240 MHz |
5260 to 5320 MHz (DFS)
5500 to 5700 MHz (DFS)
5745 to 5825 MHz
( Note: Available channel may vary with local regulations.)
Transmitting Power| 22 dBm( Note: Transmitting power may vary with local
regulations.)
Receiving Sensitivity| -58 ± 2 dBm@AC80 -MCS9; -84 ± 2 dBm@AC80 -MCS0
Antenna Gain| 9 dBi
Antenna Angle| Beamwidth [3dB] (35°± 5°)
Networking Mode| Point-to-Point, Point-to-Multipoints (less than 4 points
recommended)
Hardware Parameter| Port Numbers| 2 × Gigabit RJ45 ports
LED Indicator| Power indicator, LAN indicator, signal intensity indicator
Reset| Hardware resetting button
Power Supply| 12 VDC/1 A Passive PoE; 12 VDC, 1 A
Software Function| Application Function| TDMA, DFS, TPC
Channel Width| 20/40/80 MHz
Channel Selection| Auto/manual selection
Network Protocol| NTP (network time synchronization), IP Portal (auto search
for IP address), HTTPS (web management), SSH (debugging)
Security Mode| WPA2-PSK
Security Mechanism| Wireless network name hidden
Management Method| Web, NVMS V3
Upgrade| Web, NVMS V3
System Log| Syslog, control center information
General| Product Dimensions| 92 mm × 187 mm × 58 mm (3.62″ × 7.36″ ×
2.28″)
Package Dimensions| 132 mm × 228 mm × 91 mm (5.19″ × 8.97″ × 3.58″)
Net Weight| 0.307 kg (0.677 lb)
Gross Weight| 0.807 kg (1.779 lb)
Packing List| Wireless bridge × 1, power adapter (12 VDC, 1 A) × 1, 100 MB PoE
injector× 1, binding tape × 2, quick start guide × 1
Packing Method| Single unit packing
Working Temperature| -30°C to 70°C (-22°F to 158°F)
Working Humidity| 5% to 95% (no condensation)
Storage Temperature| -40°C to 85°C (-40°F to 185°F)
Storage Humidity| 5% to 95% (no condensation)
Installation Mode| Pole mounting
Max. Power Consumption| 4.5 W (for normal); 2.64 W~2.75 W (with 1 channel 2 M
stream IPC); 2.67 W~2.75 W (with 1 channel 4 M stream IPC); 2.75 W~2.9 W (with
1 channel 8 M stream IPC)
**Approval| EMC| FCC (47 CFR Part 15, Subpart B); CE-EMC (EN 55032:
2015,
EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011
+A1: 2014, EN 55035: 2017); IC (ICES-003: Issue 6); RCM (AS/NZS CISPR 32:
2015)
---|---|---
Safety| UL (UL 60950-1); CB (IEC 60950-1:2005, AMD1:2009,
AMD2:2013, IEC 62368-1: 2014 (Second Edition); CE-LVD (EN 60950-1: 2006 + A11:
2009 +A1: 2010+A12: 2011+A2: 2013, EN 62368-1: 2014+A11: 2017)
Chemistry| CE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC)
No.1907/2006)
Radio| EN 301 893; EN 300 440; EN 62311; EN 301 489-3; EN 301 489-17; FCC
Part 15.247; FCC Part 15.407; FCC 2.1091
Interface/Button| Description**
---|---
CPE/AP DIP Switch| Switch up or down to set the device as AP or CPE.
SSID| 4-character SSID to realize 16 kinds of matching ways by switching up or
down. The CPE will connect to the AP when its SSID matches the AP’s
PoE/LAN1| The 10/100/1000 Mbps adaptive RJ45 port, also can be used as a PoE
port.
LAN2| The 10/100/1000 Mbps adaptive RJ45 port.
Reset| Long press for 4 sec to restore to factory settings.
DC 12V| If the PoE injector is not used for powering on the device, you can
use the attached power adapter to connect the device to socket.