Tuzio W3202 Avento Towel Warmer Installation Guide
- May 15, 2024
- TUZIO
Table of Contents
Tuzio W3202 Avento Towel Warmer
Specifications
Model #| Description| Finish| Weight (lb)| Element Output (W)| Size (BTU)| WxH
(mm)| WxH (Inches)| Metal Type
---|---|---|---|---|---|---|---|---
W3202 / W3203 / W3204 / W3205 / W3206 / W3208| AVENTO TOWEL WARMER| | | | | |
|
Product Usage Instructions
Step 1: Rough-in Requirements
- The incoming power feed should go to a deep single-gang electrical box for the controller.
- Connect a power feed from the controller box to a single gang electrical box for the towel warmer.
- Ensure wall studs or plywood backing are in place at bracket locations.
Step 2: Installation Instructions
Installation Instructions (see figure 1)
- Check all items have been received. You should have received a towel warmer, hardwire kit, programmable controller, and mounting bracket kit. Read all instructions before continuing.
- Fix wall supports “B” including collar “A” to the wall using the screws provided and in locations as shown in figure 2.
- Screw the threaded pin “C”, into the threaded bushing “D” on the back of the towel warmer.
- Hang and adjust the towel warmer using set screws “E” to lock pin “C” in the wall bracket “B”. Ensure the towel warmer is firmly and safely fixed.
Step 3: Hardwire Connection
Hardwire Connection (see figure 4)
Do not connect the towel warmer to the power supply until all instructions have been read and installation is carried out by them. The heating element is 150W, 300W or 450W 110V. The element conforms to UL standards and the unit to CSA standards (File ref: 229718). Ensure the CSA label is visible. TURN OFF THE POWER SUPPLY BEFORE PROCEEDING.
- Feed the electrical cord located at the bottom of the towel warmer first through the round tube “G” and then through the cover plate “F”.
- Complete all electrical connections as shown in figure 3.
- Fit tube “G” over the towel warmer element sleeve until it meets the hexagonal chrome collar.
- Push cover plate “F” onto the tube.
- Screw the cover plate to the electric box with the enclosed screws. Adjust where necessary.
Technical Drawing
Warning : In case of damage or failure of the towel warmer the unit should be returned to the manufacturer or their distributor. The warranty of 2 years on the heating element and limited lifetime on the towel warmer frame is NOT VALID in case of improper use or installation. Do not hang the towel warmer upside down. The product is designed for use within Canada and the United States only.
Heating Element Specifications: 150 watt / 300 watt / 450 watt, 12″ long / 18”
long / 23” long, 110 volt, 60 Htz, IP55 cord, ULC approved
Material Specifications: Mild Steel – Din 2394 Quality – ST 34-2 KB /
Stainless Steel – Din 17457 Quality – 1.4301
Warranties:
- Towel Warmer Frame: Limited lifetime warranty. Refer to www.icobath.com for full warranty coverage details.
- Heating Element: 2 years
- Programmable Controller: 2 years
- Fixings: Screws, and Allen Key (if needed) are included.
- Heating Element Location: Right-hand vertical tube unless specified otherwise.
- Care & Maintenance: A periodic wash using warm water and a soft cloth will retain the high-quality finish of your towel warmer for many years to come. ON NO ACCOUNT should any household bleaches, detergents, abrasive polishes, steel wool, or other cleaning agents be used on this item.
FAQs
- Q: What should I do in case of towel warmer failure?
- A: In case of damage or failure, return the unit to the manufacturer or their distributor.
- Q: What is the warranty on the product?
- A: The warranty is 2 years on the heating element and a limited lifetime on the towel warmer frame, provided there is no improper use or installation.
- Q: Can the product be used outside of Canada and the United States?
- A: The product is designed for use within Canada and the United States only.