Liberty L3NVR4POE NVR Network Video Recorder User Guide

Liberty L3NVR4POE NVR Network Video Recorder

Precautions

Fully understand this document before using this device , and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WA RN I NG| It alerts you to moderate dangers which , if not avoided , may cause minor or moderate injuries.
---|---
C A UT I ON| It alerts you about risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
N O TE| It provides additional information.

WARNING

• Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
• Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
• Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
• If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
• When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from th is device.
• If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
• Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth in to slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
• Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
• Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
• Keep the device away from moist, dusty, extremely hot or cold places.
• If the device is installed outdoors, take insect- and moisture proof measures to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.

Special Announcement

• All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
• The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
• This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
• This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE
For more information, please refer to website.

Supplier’s Declaration of Conformity

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information Unique Identifier : L3NVR4POE

Responsible Party – U.S. Contact lnformation : Liberty Wire & Cable, Inc.
1490 Garden of the Gods Rd, Ste F Colorado Springs, CO 80907 855.388.7422

Warranty: The manufacturer warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of three (3) years from the original invoice date.

Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.

Table 1-1 Packing list

Device Structure

Device Ports

NOTE

Different device may have different ports and multi-head cable, please refer to the actual product.
Front panel description of device refer to table 2-1.

Table 2-1 Front panel description

P o rt N a me| De sc r i p t ion
---|---
PWR Indicator| When the NVR is operating, the PWR indicator is steady on .When the NVR is shut down, the PWR indicator is turned off.
HOD Indicator| Hard disk status indicator This indicator flashes when data is transmitted.
POE Indicator| POE network status indicator This indicator flashes when data is transmitted.
KB/MOUSE| Supports connection to an USS mouse or keyboard
BACKUP| Supports connection to an USS flash drive or USS removable hard disk.

Rear panel description of device, please refer to table 2-2.

Table 2-2 Rear panel description

HDMI
Alarm 1/0| Alarm input/Alarm output
DC48V| Connected to an external power adapter
| Power switch
USB| USB 2.0 port

Device Dimensions

NOTE

Different device may have different dimensions, please refer to the actual product.

Device Installation

Take the following steps to install hard disk :

Step 1 Remove the screws for fixing the cover and take down the cover.
Step 2 Take out the screws and mount two of them to the screw holes, as shown in figure 3-1.

NOTE
Just screw the screws about 1 to 2 turns, instead of tightening.

Step 3 Route the screws through the cucurbit holes on the base, push the hard disk to the appropriate position, as shown in figure 3-2.

Step 4 Turn the device over, and mount another two screws to the holes as shown in figure 3-3. Then Fastenal screws.

Step 5 Insert the hard disk data cable and power cable, then put on the upper cover and fasten the fixing screws.

Device Operation

Startup

Before starting NVR, ensure that the NVR is connected to a power supply properly and a monitor is connected to the HDMI or VGA interface of the NVR correctly. After starting the NVR, there is a login window located in the center, as shown in figure 4-1.

CAUTION

In some environments, if the power supply is abnormal, the NVR may not work properly. In severe cases, the NVR may be damaged. In these environments, you are advised to use regulated power supply.

NOTE
User needs to create a new password to activate the device, when logging in at first time.
User can also set pattern unlock to quickly login.Set security questions to recovery password.
Change the language at logging in interface.

Topology of the NVR

NVR with POE ports can access IIP cameras immediately when plug IP cameras in to NVR’s POE ports. Then the NVR will assign an IP address for each camera automatically. The topology refer to figure 4-3.

Power off

Enter the path Main Menu >System > Maintenance > Shutdown to power off the NVR.

NOTE

Before replacing the hard disk, the power must be turned off.

Quick Configuration

Plug in power to access the NVR user page, the wizard window would show at first time, user can configure quickly or close immediately. The details of configure please refer to main menu. Use mouse to right-click any where of the main interface to access the main menu. Main menu comprises Channel, Record, Alarm , Network and System settings, as shown in figure 5-1.

Channel

Channel settings contain Camera, Encode, Sensor Setting, OSD, Privacy Zone, ROI, Microphone.

• Camera: user can add cameras automatically by clicking Click to Add , and add manually by clicking add. Tick cameras then click Delete to delete cameras. User can batch update software.
  

• Sensor Setting: set the sensor parameter of channels’ cameras.

• OSD / Privacy Zone/ ROI : set on live video screen.

• Microphone: adjust and set the microphone of channels.

• All these settings can be copied to other channels by clicking copy button.

Record

Record settings contain Record Schedule, Disk, Storage, Disk Calculation, SMART and Disk Detection.

Set record schedule and storage strategic. user can calculate the disk using time at Disk calculation interface.

Enter SMART interface to view the state of disks. Disk detection can detect the disks.

Alarm

Alarm settings contain General , Motion detection, Video loss, Intelligent analysis, Alarm in, Abnormal alarm, Alarm out as shown in figure 5-2

General : enable or disable alarm and set duration time of alarm.

• Motion Detection : enable th is function, if detection the motion actions, it will alarm.
  • Event actions : contain buzzer, alarm out, push message to App, pop-up message to monitor, send E-mail and post recording( after enabling, choose the recording time from drop list.)
  • Area : set motion detection area. Press left button and drag the cursor to add a detection area ,and double-click an area to delete it.
  • Schedule: set schedule to enable or disable motion detection alarm. There are three methods to set, click the double arrows button to choose all day .The second, click and drag the cursor to select periods. The third, click one by one.
• Video Loss , Intelligent Analysis are same settings as motion detection.
• Alarm In: settings for 1/0 alarming. Abnormal Alarm can tick disk error, IP conflict, network disconnected.

Network

Network settings contain Network, 802.1X, DONS, E-mail, Port Mapping, P2P, IP Filter and SNMP as shown in figure 5-3.

• Network,802.1X, DONS, and SNMP interface to set network parameters.

• E-mail: set E-mails for sending and receiving alarm messages and password retrieva l message.

• Port Mapping: set the ports for remote accessing.
  P2P: add NVR into device list of App by accessing the QR code.

• IP Filter : settings for creating black list or white list.

System

System settings contain Information, Genera l, User, Security Center, Auto Sequence, Logs, Maintenance and Auto Restart, as shown in Figure 5-4.

• General: include system, date and time , time zone, DST.
• User: add user and set advance setting(auto login, password double authentication, boot wizard).
• Security Center: modify the password, pattern unlock, secure Email, Secure question.
• Auto Sequence: settings for sequencing view of the channels.
• Logs: shows operating and alarm log, user can export logs if an USB disk is plugged in.
• Maintenance: include shutdown, reboot, exit system, reset, import configuration , export config uration and update.
• Auto Restart: enable this function to make device restart periodically.

Live Video

Live video page is showed after starting the NVR by default, as shown in figure 5-5.

Mobile Client

Search for “Liberty View• in App Store or Google Play to download and install the mobile client. Use the App to scan the QR code on the back board of NVR, or in P2P settings page in NVR user interface. Then input the password of the NVR to add the NVR into the device list of the App. User can manage the device through mobile client.

Web Accessing

The NVR also can be accessed in a Web browser. Open a web browser like IE and enter the IP address of device (DHCP is on by default) in the address box, and press Enter. The login page is displayed as shown in figure 7-1.

NOTE

The user name and password are same as the UI interface.

CUSTOMER SUPPORT

Liberty Liberty Wire & Cable, Inc. 1490 Garden of the Gods Rd, Ste F Colorado Springs, CO 80907 – 855.388.7422 – www.libertyonline.com

References

• Liberty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>