LEDIARY Boho Ceiling Fans with Lights 20 Inch Flush Mount Ceiling Fan User Manual

LEDIARY Boho Ceiling Fans with Lights 20 Inch Flush Mount Ceiling Fan

INTRODUCTION

WARNING!!! To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your user’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning the unit, switch off the power at the service panel and lock the service panel to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.
3. Be cautious around the fan and blades when clearing, repairing, or working near the fan. Always turn off the power to the ceiling fan before performing any servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. This appliance is not intended for use by young children or individuals with disabilities without supervision. Young children should be supervised to ensure they do not play with the appliance.
6. Before installing your ceiling fan, refer to the section on the proper method of wiring your fan. If you feel that you do not have enough wiring knowledge or experience, it is recommended to have your fan installed by a licensed electrician.

Before Installation

• This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan.
  • NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing contact us.

Accessories

Check to see that you have received the following parts:

Package Contents

Check to see that you have received the following parts

Energy Saving Usage

• Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.

Choosing the Appropriate Mounting Location

• Ceiling fans should be installed or mounted in the middle of the room and positioned at least 7 feet above the floor and 18 inches away from the walls.
• If the ceiling height allows, it is recommended to install the fan 7~9 feet above the floor to achieve optimal airflow.

Turn Off When Not in the Room

• If the room is unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

• Summer Season: Use the ceiling fan in the counterclockwise direction.
  • The airflow created by the ceiling fan produces a wind-chill effect, making you feel cooler.
  • Select a fan speed that provides a comfortable breeze; lower speeds consume less energy.
• Winter Season: Reverse the motor and operate the ceiling fan at a low speed in the clockwise direction.
  • This produces a gentle updraft, which pushes the warm air near the ceiling down into the occupied space.
  • Remember to adjust your thermostat when using your ceiling fan. This simple step can lead to additional energy and cost savings.

Electrical and Structural Requirements

• Your new ceiling fan will require a grounded electrical supply line of AC 110-130V/60Hz and a 15 Amp circuit. According to electrical codes, it is necessary to use a fan-rated outlet box to support the additional weight and motion associated with a ceiling fan. A fan-rated box will be clearly labelled as such and is typically designed to support ceiling fans weighing up to 70 pounds.
• Fan-rated outlet boxes are available in various ratings and designs. It is essential to ensure that the rating of your ceiling fan outlet box meets the requirements for the specific ceiling fan you are installing. Please refer to the figures below for different structural configurations that can be used for mounting the outlet box.

Low-profile use (Figure 1)

• A 1/2-deep pancake box is meant to be screwed to a joist or block It’s used if one cable is coming into the box. It is also available in a saddle-mount configuration.

Deep-profile use (Figure 2)

• A 2-1/4″ deep box can be attached to a block between joists and is roomy enough to handle more than one cable.

Brace use (Fiqure 3)

• Paired with a deep box, this hanger is meant to span between two joists and takes the place of wooden blocking.
• If your fan is to replace an existing light fixture, turn the power off at the main fuse box and remove the existing light fixture.

WARNING

• To ensure safety and prevent potential electrical shock, it is not sufficient to simply turn off the wall switch. Before wiring, make sure to turn off the electricity at the main fuse box.
• All wiring should be done by national and local electrical codes.
• Additionally, it is important to properly ground the ceiling fan as a precautionary measure against possible electrical shock.
• Following these guidelines will help ensure the safe installation and operation of your ceiling fan.

WARNING

• Do not use a variable (rheostat) wall controller or dimmer switch to operate this fan.
• Doing so can cause damage to the ceiling fan’s remote control unit. It is recommended to only use the provided remote control.

Installation

• Turn off the electric circuit at the main fuse or circuit breaker box.
• Loosen the four canopy screws(don’t take off) and then twist counter-clockwise to remove the ceiling plate.
• The mounting bracket must be securely fastened to a structural ceiling member.
• Use wood screws to fix the bracket for a wooden or false ceiling.
• Tighten the light bulb by rotating it clockwise.
• Use the safety rope(pre-installed) to hang the lamp to the ceiling plate.
• Wiring: To facilitate wiring, use a safety rope to hang the lamp body. Connect the”Neutral wire” (white wire) from the ceiling to the white wire. Connect the “Live wire” (black wire) from the ceiling to the black wire. Connect the “Ground wire” (green or yellow/green or bare) from the ceiling to the green wire.
• Align the grooves on the canopy with the screws on the bracket, and then push the fixture upwards.
• Rotate the canopy counterclockwise and tighten the four screws with a screwdriver.
• Finish installation. Turn on the electric power at the main fuse or circuit breaker box.

Operate Your Ceiling Fan

• IMPORTANT: Using a full-range dimmer switch to control fan speed will damage the fan. To reduce the risk of fire or electrical shock, do not use a full-range dimmer switch to control the fan speed. (Figure 1).
• Only control light on/off via wall fan switch.
• Restore electrical power to the outlet box by turning the electricity on at the main fuse box. (Figure 2).

Installation Recommended

• Room Size:
• Room Height:

Remote Control

Wall Plate Installation

• Attach the wall plate using the two screws provided.

Troubleshooting

Contact Us

Customer Service:

• 30-Days Full Refund Guarantee
  • If you are not completely satisfied or the item isn’t what you expected, just tell us within 30 days.
  • We will give you a full refund unconditionally.
• Quick Response within 12 Hours
  • You can contact us without hesitation at any time of the day, and we will reply to you within 12 hours.
  • (It would be appreciated if you could provide us with a video or pictures, if available)
• Friendly Reminder
  • It’s better to contact us than to leave a negative shopping experience.
  • Nothing is more important than your satisfaction, and we will do our best to serve you.
• 2-year Warranty
  • We will send you brand-new items for free or provide a full refund if any quality problems occur within 2 years from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>