JUNG BT..1002 Push Button 1 Gang Battery Powered Instruction Manual

BT..1002 Push Button 1 Gang Battery Powered
Instruction Manual

Operating instructions

BT..1002 Push Button 1 Gang Battery Powered

JUNG HOME push-button 1-gang, battery-powered Art. no. BT..1001
JUNG HOME push-button 2-gang, battery-powered Art. no. BT..1002

Safety instructions

This device or its accessories are supplied with batteries in the form of button cells.
DANGER! Batteries can be swallowed. This can lead directly to death by suffocation.
Dangerous substances may cause severe internal burns leading to death within 2 hours.
Keep new and used batteries away from children.
Do not use devices if the battery compartment does not close securely and keep away from children.
If you suspect that a battery has been swallowed or is in any orifice of the body, seek immediate medical attention.
WARNING! Improper handling of batteries can result in explosion, fire or chemical burn due to leakage.
Do not heat or throw batteries into fire.
Do not reverse polarity, short-circuit or recharge batteries.
Do not deform or disassemble batteries.
Replace batteries only with an identical or equivalent type.
Remove empty batteries immediately and dispose of in an environmentally friendly manner.
Remove empty batteries immediately and dispose of in an environmentally friendly manner. Do not throw batteries into household waste. Consult your local authorities about environmentally friendly disposal.  According to statutory provisions, the customers are obligated to return used batteries.
Read the instructions in full, observe them and keep them for future reference.

Device components

(1) Base plate
(2) Fastening screws for the base plate
(3) Design frame
(4) Push-button module with battery compartment on rear side
(5) Fastening screws for push-button module
(6) Rocker
(7) Light guide (status LED)
LED indication during operation (display goes out after 5 seconds)

Green| If the output is switched on, the venetian blind, shutter and awning move
---|---
Orange| If the output is switched off, the venetian blind, shutter and awning are stationary
Red| Disabling function active, e. g. continuously ON/OFF
Flashing green/red| Device update is being performed
Slow flashing green| Push-button found in configuration mode
Slow triple red flashing, after pressing button| Low battery charge level
White on a few seconds, then off| Battery charge level is measured (only after ex- change of battery)

*Colour adjustable

Intended use

• Operation, e.g. of venetian blinds, shutters, awnings, lighting or fans
• Wireless connection to devices from the JUNG HOME system
• Mounting on appliance box with dimensions according to DIN 49073
• Screw fastening on walls or adhesive mounting on smooth surfaces

Product characteristics

• Commissioning using JUNG HOME app on mobile end device (smartphone or tablet) via Bluetooth
• Operation of top, bottom and full surface with up to two linked functions per rocker
• Using buttons to operate the actuator when in use or the wirelessly linked JUNG HOME actuator
• Using buttons to control central functions or call up scenes
• Multi-colour status display
• Actuator state feedback via status LED
• Message of battery status via LED and app
• Disabling of local operation
• Bluetooth SIG Mesh for fully encrypted wireless communication
• Updating via JUNG HOME app
• Using buttons to trigger disabling function and restraint

Operation

All settings and operations can be configured individually using the JUNG HOME app.
Configuration in the JUNG HOME app: The default setting with the “rocker” operating concept is described in the table.

on at top, bottom of with full surface alternately
Dimming1| Switch on at top, bottom of with full surface to switch- on brightness / switch off alternately| Top: dim brighter / bottom: dim darker
Move venetian blind / shutter / awning2| Stop or adjust the slats| Top: move up / bottom: move down
Heating1| Increase the target temperature at the top by 0.5 °C / Decrease the target tem- perature at the top by 0.5°C| –
Operating scenes1| Call up scene at top or bot- tom| Call up scene at top or bot- tom
Operating an area (group)1/2| Depending on the unit, as described for switching, dimming, venetian blinds and heating| Depending on the unit, as described for switching, dimming, venetian blinds and heating
Disabling function (lock-out protection, restraint)1| –| Top: activate / bottom: deactivate
Changing the colour temperature (with DALI insert)| | Top: increase colour temperature / bottom:
decrease colour temperature

1. Brief push-button action < 0.4 s < long push-button action
2. Brief push-button action < 1 s < long push-button action

Configuration in the JUNG HOME app: “button” operating concept

off
Dimming1| Alternately switch on / switch off switch-on brightness| Alternately dim brighter / dim darker
Move venetian blind / shutter / awning2| Stop or adjust the slats| Alternately move up / move down
Heating1| –| –
Operating scenes1| Recalling scenes| Recalling scenes
Operating an area (group)1/2| Depending on the unit, as described for switching, dimming, venetian blinds and heating| Depending on the unit, as described for switching, dimming, venetian blinds and heating
Disabling function (lock-out protection, restraint)1| –| –
Changing the colour tem- perature (with DALI insert)| –| Alternately increase colour temperature / decrease col- our temperature

1. Brief push-button action < 0.4 s < long push-button action
2. Brief push-button action < 1 s < long push-button action

Mounting

The communication of the JUNG HOME devices and linked mobile end devices is carried out in wireless mode within the range of the Bluetooth Mesh network.
Wireless signals can be affected in their range through:
– Number, thickness, position of ceilings, walls and other objects
– Material type of these objects
– High-frequency interfering signals
Observe the following fitting instructions to maximise the range:
– Plan the positions and number of JUNG HOME devices to keep the number of ceilings and walls between two devices as low as possible
– If JUNG HOME devices are installed on both sides of a solid wall, they should be positioned as close as possible to each other on the opposite sides of the wall. This keeps the attenuation of the wireless signal  through the wall as low as possible
– When planning, observe that the number of building materials and objects that attenuate the wireless signal strongly (e. g. concrete, glass, metal, insulated walls, water tanks, pipelines, mirrors, book cabinets,  storage rooms and refrigerators) on the connection line between JUNG HOME devices is as low as possible
– Keep a distance of at least 1 m from devices that emit high-frequency signals (e. g. microwave, motors) or run with wireless signals at 2.4 GHz (e.g. WLAN router, baby monitor, IP cameras, wireless loudspeakers etc.)

DANGER!
Electrical shock on contact with live parts in the installation environment.
Electric shocks can be fatal.
When mounting in a multiple combination, disconnect 230 V devices. For this, switch off all corresponding circuit breakers, secure against being switched on again and check that there is no voltage.
Prior to mounting, insert battery (see chapter “Commissioning”).

• Screw or glue the base plate (1) to an even surface. The TOP/OBEN label has to be at the top.
• Attach design-frame (3) to the base plate.
• Fasten the push-button module (4) to the base plate with the supplied screws (5).
• Snap on the rocker (6) (see figure 1) and (see figure 2).

Information on gluing mounting
The substrate must be flat and free of dust and grease.

• Remove the rear, unpunched film of the enclosed adhesive pad.
• Align the adhesive pad, stick it to the surface and smooth it out. Remove air bubbles.
• Remove the two inner segments of the front film.
• Align the base plate to the external punching and stick it on.
  In the case of multiple combinations, cut off the abutting sides using a ruler and a cutter. (see figure 3).

Commissioning

Inserting the battery
Observe the safety instructions for the batteries. Keep contacts of batteries and device free of grease.

• With the device mounted, carefully remove the rocker (6) from the push-button module (4) (see figure 1), (see figure 2) and unscrew the push-button module (4).
• Apply battery to the positive contact on the side of the battery holder. Observe polarity: the positive pole of the battery must be at the top.
• Press gently on battery to snap it in.
• Mount the push-button module (4) on the base plate and snap on the rocker (6).

Commissioning with app

Prerequisite: the JUNG HOME device has not yet been made a participant in a Bluetooth Mesh network; otherwise reset the device to factory defaults.
If a Bluetooth Mesh network (project) does not yet exist, start by creating a new project for the first JUNG HOME device in the JUNG HOME app.
If a Bluetooth Mesh network already exists, the project file for this network must be opened in order to pair the new device.
This battery-powered JUNG HOME device always requires a mains-supplied JUNG HOME device as a so-called “Friend node”. The mains-supplied device must be within range (typ. 30 m) of this device and added to the BT-Mesh network before the battery-powered device.
After inserting the battery, the device is automatically in pairing mode for 2 minutes.

• Activate pairing mode manually:
  Press the left button over entire surface for longer than 4 seconds.
  The status LED flashes slowly in blue. Pairing mode is active for two minutes.

• Start the JUNG HOME app.
  The app shows all devices in pairing mode.

• Select a device in the app.
  To identify the selected device, its status LED flashes more quickly in blue.

• Add the device to the project.
  The status LED lights up in blue for five seconds to confirm that pairing was successful.
  If the status LED flashes red very fast, pairing has failed and needs to be retried.
  The JUNG HOME app can then be used to link devices wirelessly and configure the parameters and operation (see list of functions and parameters).
  Once the commissioning of the JUNG HOME project has been completed, hand over the project file to the customer.

Besides basic commissioning, the JUNG HOME app enables device updates and convenient operation of further individual configuration options:
– Link: A button, binary input or motion sensor can be controlled by linking it to a load (e. g. dimmer, socket, switching output, shutter, etc.). Several loads can be controlled together by linking them to an area or  scene.
– Area: Different loads (e. g. dimmer, socket, switching output, shutter, etc.) can be grouped in an area to allow them to be controlled together.
– Scene: Different loads (e. g. dimmer, socket, switching output, shutter, etc.) can be grouped in a scene so that, by calling up a scene, each load assumes the load status stored in the scene.
Resetting the device to the factory setting
If local operation is disabled, resetting to the default setting can only be performed within 2 minutes after removing the battery for at least 10 seconds and reinserting the battery.
If the device has already been added to a project with the JUNG HOME app, it can be reset also to the default setting in one step with the “Delete device” function from the app.
If the device cannot be reset to the default settings with the app or the app is not at hand:

• Press the left button over its entire surface for longer than 20 seconds until the status LED quickly flashes red.
• Release the button and press it briefly once again within 10 seconds.
  The status LED flashes in red more slowly for approx. five seconds. The device has been reset to the default setting.
  After resetting the device to the default setting, it must be removed from the JUNG HOME app provided it has not already been deleted from the app.

Dismantling

The rockers can be dismantled using a dismantling wedge or a screwdriver.
The recesses are intended for a blade width of up to 4 mm.

Technical data

List of functions and parameters

The JUNG HOME app can be used to configure all functions of the JUNG HOME device and its behaviour in the Bluetooth Mesh project for the respective individual  purposes.
All devices created in the JUNG HOME app can be used independently and set separately.
To reach the configuration mode:

• Select the battery-powered push-button in the app.
• Press any button on the device in order to activate the configuration mode.

operation of the button at the top or button applies to the same load, same area or same disabling function.
Operation at the top or bottom usually leads to directly opposite reactions. (E. g. light on/off, brighter/darker, move up/ down)
Button: Operation of the button at the top or bottom applies to different loads, areas or scenes. When controlling loads or areas, renewed operation of the same pressure point will lead to opposite reactions (e. g. light on/off, brighter/darker, up/ stop/down).
Behaviour of the status LED when switched on or moving| Colour selection Default setting: green| LED colour and brightness: when load is switched on, venetian blind / shutter / awning moves.
Behaviour of the status LED when switched off or stationary| Colour selection Default setting: orange| LED colour and brightness when a load is switched off or a venetian blind / shutter / awning is stationary.
Operating lock| No lock, factory reset lock, operating lock Default setting: no lock| Factory reset lock: prevents resetting on the device and hence the removal from a project and pairing again by unauthorised persons. After the mains voltage  returns, the factory reset lock is deactivated for two minutes.
Operating lock: prevents normal operation on the device and hence the
load from being controlled. This lock can be used, for example, to restrict manual access temporarily.
Operation via the app remains possible. The operating lock cannot be deactivated on the device.

** Available by update in the future: You can find notes on updates and dates at www.jung.de/JUNGHOME

Accessories

Conformity

Albrecht Jung GmbH & Co. KG hereby declares that the radio system type art. no. BT..1001 and BT..1002 meets the directive 2014/53/EU. You can find the full article number on the device. The complete text of the  EU Declaration of Conformity is available under the Internet address: www.jung.de/ce

Warranty

The warranty is provided by the specialist trade in accordance with statutory requirements.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Shilshole
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
kundencenter@jung.de

ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Shilshole
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
kundencenter@jung.de
www.jung.de
22.09.2023
32405713 J0082405713
Product image non-binding

References

• JUNG - Switches and systems
• JUNG - Konformitätserklärung
• JUNG - JUNG HOME New Items

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>