SMART BATH Ultra NOVA Bidet Seat Owner’s Manual

SMART BATH Ultra NOVA Bidet Seat

Features

Please confirm the model you purchased first, and then check the corresponding function. The model and specification can be found on the nameplate at the rear of the machine.

Warnings and precautions

• Do not kink the  water hose
• Do not get the unit wet
• Unplug before cleaning
• Only use natural cleaners on the  unit
• Use with GFCI outlet only
• If an extension cord is needed use a 14 or 12 gauge
• This unit is only intended for use as described in this manual
• Do not use it if the unit is damaged

Parts

Parts list

Installation

Size requirements of bidet seat

• Distance from the water tank to the front of the toilet: 19.9” – 21” (505-535mm).
• Distance from mounting holes to the back edge of the toilet bowl: >2.75” ( 70mm).
• Spacing between two mounting holes: 4.6” – 7.2” (118-182mm).
• Distance from mounting hole to water tank: >1.2” (30mm).

Preparation before installation

Before installing the bidet seat:

• Remove the existing toilet seat and turn off the Water Supply Valve
• Flush the toilet and hold down the flush lever or button for 5 to 10 seconds.
• Place a sponge, rag, or bucket under the toilet water inlet.
• Disconnect the toilet’s Water Supply Hose from the toilet’s Water Inlet.

Install the Mounting Plate

• Push the Rubber Sleeve into the Mounting Hole of the Toilet.
• Place the Mounting Plate over the
• Mounting Holes in the Toilet and align it using the Cardboard
• Installation Guide.
• Place Locking Brackets over
• Mounting Holes.
• Slide Bolts through the Locking
• Bracket and into the Rubber
• Sleeves.
• Tighten Bolts.

Note
For uneven ceramic, add a 2mm thick pad at the rear end of the Mounting Plate.

Secure Ultra NOVA Seat

Align the bottom of the Seat with the Mounting plate, and push toward the Toilet Tank. When you hear the “click” sound, it indicates that it is locked in place.

Installation (Auto-Flush)
Install the external automatic flushing unit (Only for Ultra NOVA +)

Ander Tan Chich Alinder died

1. Turn off the power and water.
2. Remove the Toilet Tank Cover
3. Measure the outer diameter and height of the top of the Top Flush Cylinder. The diameter should be between 2½in and 3⅛in and the height should be above ¾in otherwise the Automatic Flushing
4. The module is not usable.
5. Find the appropriate-sized collar. The collar should be able to fit around the flush cylinder but its ends should not be able to touch each other.
6. Secure the collar to the flushing module by sliding it sideways with the screw holes on the collar facing up, as shown below. (You should hear a click)

Installation and fixation of flushing module

1. Place the Automatic Flushing Module into the top of the fittings as shown in the figure.
2. Make sure the Push Rod is aligned with the Flush Button. If the Push Rod cannot be pressed the
3. Flush the Button, and insert the Adjusting Block into the Push Rod.
4. Tighten the Wing Bolt to secure then tighten 4 Clamp Screws.
5. Secure the power cord at the screw position with a tie (If there is a groove in the top of the water tank, pass the wire through the groove).
6. Turn on the water source, connect the power supply, and test the manual and automatic flushing functions.
7. Close the water tank cover.

Connect all water supply parts

• Screw T-Connector onto the toilet.
• Screw the Toilet Supply Hose onto the bottom of the T-Connector.
• Screw the Water Filter onto the side of the T-Connector
• Screw one side of the Ultra-NOVA Supply Hose onto the filter and the other side to Ultra-NOVA Water Inlet.
• Turn on the Water supply shutoff.
• Check all connections for leaks.

Connect power

Caution

• The outlet must have GFCI (Ground-fault circuit interrupter).
• The outlet must be on a 15+ AMP dedicated circuit.
• The cord is limited to 4 feet by law.
• If an extension cord is used, it must be 14 gauge or larger.

Remote Control installation

Install Batteries

• Remove the Battery Door from the back of the remote by pressing on the door and sliding away from the remote.
• Insert 2 AAA Batteries and close the Battery Door.

Secure Wall Mount

• Sticker Installation method
• Remove the Adhesive Sticker on the back of the Wall_ Mount (and Guide if desired).
• Adhere the Wall Mount (and Guide) to the wall in the desired position.

Screw Installation method

1. Place the Wall Mount on the wall in the desired location and mark the locations of screws on the wall through the holes on the Wall Mount.
2. Remove the Wall Mount and drill holes in the marked locations.
3. Insert Expansion Tubes into the wall.
4. Place Wall Mount (and Guide if desired) on the wall and thread the Screws into the Expansion Tubes in the holes on the Wall Mount.

Place Remote in Wall Mount
(Use of the Guide is optional, but many people find it helpful to find features on the top of the remote easily while seated.)

Testing Before Use

1. Check power supply is securely connected to the wall outlet.
2. Activate the seat Skin Sensor by placing a hand or wet rag on the seat where indicated. (If hand or wet rag doesn’t work place bare bottom on the seat).
3. Press a wash button on the remote place a hand or cup over the nozzle as it comes out and wait until the wash begins.
4. Press Stop or remove the hand/rag from the Skin Sensor.SUCCESS!!! Your Ultra-NOVA is ready for use.

Operation

Side Controls

• Turn backward to start a Rear Wash.
• Turn forward to start the Front Wash
• Long press (2 seconds) to start the Enema Wash.
• Once a wash has started:
• Turn the knob forward to increase pressure and backward to reduce pressure.
• Press in on Knob to stop Wash.
• When stopped, press Knob to start Dry.

Water Temperature Button

• Short press the button to switch the water temperature.
• Long press during the wash to switch the nozzle from oscillation to stationary and back.
• Seat Temperature Button
• Short press to switch the seat temperature.
• Long press during the wash to switch the nozzle position. (positions cycle 1,2,3,2, 1,2,3…)

Remote Control button layout

Cleaning

Nozzle Cleaning
Press the “nozzle cleaning” button on the remote and the nozzle will automatically come out. Use cleaner and a soft cloth or soft-bristled brush to clean the nozzle. When done cleaning, pres Stop button and nozzle will go back into the seat.

External Cleaning
Clean the product with a soft cloth and natural cleaners. Do not use strong chemicals on the seat as they can damage the anti-bacterial coating on the unit.

Clean the filter screen
If you feel that the water flow is less than original during normal use, clean the Filter Screen. To clean the Filter Screen, turn off the water supply, flush the toilet, and disconnect the Supply Hose from the side of the seat. Remove Filter Screen from the Water Inlet and scrub it with a soft bristled brush. After cleaning reassemble and turn on the water supply.

Remove the seat to clean the toilet
If you need to access the underside of the seat for cleaning, turn off the water and power first. Then push the release button on the right side (while facing the toilet) and pull the seat forward. The seat can be reinstalled by sliding it back into the mounting plate until it clicks into place.

Troubleshooting

CAUTION
If leaking, immediately shut off the water supply and unplug the unit!

for power and plug seat in to wall outlet.
No water| Check water supply shutoff valve| Open if closed
 | Is the supply hose kinked| Adjust the hose to unkink it
 | Are you covering the seat sensor with skin to activate it?| Move your body to fully cover skin sensor
Water pressure low| Is water pressure setting low| Press Pressure + button on remote
 | Check filter| Replace filter every 6 months
Water temperature low| Is the water temperature set to low| Press Water Temp button to adjust temp
Seat temperature low| Is the seat temperature set to low| Press Seat Temp button to adjust temp
Air temperature low| Is the air temperature set to low| Press Air Temp button to adjust temp
Wash stops running| Has it run for more than 90 seconds| Not a malfunction (cycle runs for 90 sec)
 | Has it run less than 90 seconds| Move your body to fully cover skin sensor
Dry stops running| Has it run for more than 3 minutes| Not a malfunction (cycle runs for 3 min)
Remote control not responding| Has it run less than 3 minutes| Move your body to fully cover skin sensor
Water connection leaking| Is the connection lose| Tighten the connection
 | If the connection missing a rubber washer| Replace the rubber washer
Flashing red light| Flashes red once: seat temp sensor alert| Sensor open or short circuit seat will beep and stop heating
 | Flashes red twice: air temp sensor alert| Sensor open or short circuit seat will beep and stop heating
 | Flashes red three times: Water temp sensor alert| Water temp above 113°F (After 3 beeps it returns to normal).

Troubleshooting / Warranty
For more Troubleshooting or to view the warranty for this product, scan this QR code or go to: https://NovaBidet.com/Warranty/

Technical Specifications

Model

Technical

parameters

|

Ultra-NOVA

|

Ultra-NOVA+

---|---|---
Power type|

AC 120V~ 60Hz

Rated power

| Max 1220W = 10.1Amps

(with inlet water temperature of 60°F and water temperature set to maximum)

Power cord length

|

4 feet

Warm water heating type|

Instant heating

Water temperature| The temperature adjustment range is about 86°F – 102°F

Safety devices

| Flow monitoring sensor, water temperature sensor, temperature control switch, temperature fuse.
Air temperature| Adjustable temperature range (room temperature – 131°F)

Drying heating power

|

200W

Seat surface temperature

|

Adjustable temperature range (room temperature – 104°F)

Seat heating power|

40W

Water supply pressure| 22psi – 105psi
Environment temperature| 38°F – 104°F

Product size

|

L505xW375xH93mm

L19.9in x W14.75in x H3.66in

Product net weight

|

4.2kg 9.25lbs

|

4.4kg 11lbs

This device complies with Part 15 of the FCC rules.

References

• Warranty

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>